{RAY}[DEVELOPMENT] - CM9.1 - FreeXperia Project

Search This thread

sameq

Member
Aug 23, 2011
27
2
I have a problem rom runs smooth for 1min but then it becomes a little choppy and than it runs smooth again. I think its a kernel issue.
 

Griffee

Senior Member
Apr 30, 2012
86
8
Podolsk
Very-very-very nice ROM.
Few bugs're still here:
- WiFi works only with predective WAP and fails with AUTO WPA/WPA2
- video recording stills the camera but not the system
- block/unblock device turns the brighness to default
- most annoying problem is volume doring the call (time to time).

For the brightness problem I use solution I found on the 4PDA forum:

system/etc/hw_config.sh

should be

LMU AS3676 Configuration
dev=/sys/devices/i2c-0/0-0040/leds/
echo 0,0,0,0,0,0,0 > $dev/lcd-backlight/als/curve

Now it's OK.

Battery life is not amaizing but reeeeeel good.
 
Last edited:
  • Like
Reactions: duxxyuk and Srkineo

Srkineo

Senior Member
Sep 24, 2010
318
78
Geel
Very-very-very nice ROM.
Few bugs're still here:
- WiFi works only with predective WAP and fails with AUTO WPA/WPA2
- video recording stills the camera but not the system
- block/unblock device turns the brighness to default
- most annoying problem is volume doring the call (time to time).

For the brightness problem I use solution I found on the 4PDA forum:

system/etc/hw_config.sh

should be

LMU AS3676 Configuration
dev=/sys/devices/i2c-0/0-0040/leds/
echo 0,0,0,0,0,0,0 > $dev/lcd-backlight/als/curve

Now it's OK.

Battery life is not amaizing but reeeeeel good.

That is one hell of a first ever post! +1thank for you^^

used this trick to fix brightness issue in my new AOKP rom
 

duxxyuk

Senior Member
Jun 28, 2010
273
76
Lyon
Redmi Note 9 Pro
Google Pixel 7a
That basically disactivates the Ambient Light Sensor and all automatic routines. It works but would it not be better to use the Ambient Light Sensor ?

to activate brightness adjustement Echo 3,2,2,0 as shown below :

LMU AS3676 Configuration
dev=/sys/devices/i2c-0/0-0040/leds/
echo 3,2,2,0 > $dev/lcd-backlight/als/curve
 

Griffee

Senior Member
Apr 30, 2012
86
8
Podolsk
That basically disactivates the Ambient Light Sensor and all automatic routines. It works but would it not be better to use the Ambient Light Sensor ?

to activate brightness adjustement Echo 3,2,2,0 as shown below :

LMU AS3676 Configuration
dev=/sys/devices/i2c-0/0-0040/leds/
echo 3,2,2,0 > $dev/lcd-backlight/als/curve

Would it work in all-auto mode?
Reason I used all theros was using manually set brightness all the time (because every device blocking canceled brightness settings).

Still having problem with call volume. It's not DSP problem as I thougt before. volume is normal/low in 50/50 cases.

---------- Post added at 01:40 PM ---------- Previous post was at 12:43 PM ----------

Tested new wariant of configuration.
Nope, I still can't set brightness manually.
But now it seems like brightness auto-level works.
 
  • Like
Reactions: duxxyuk

Srkineo

Senior Member
Sep 24, 2010
318
78
Geel
Would it work in all-auto mode?
Reason I used all theros was using manually set brightness all the time (because every device blocking canceled brightness settings).

Still having problem with call volume. It's not DSP problem as I thougt before. volume is normal/low in 50/50 cases.

---------- Post added at 01:40 PM ---------- Previous post was at 12:43 PM ----------

Tested new wariant of configuration.
Nope, I still can't set brightness manually.
But now it seems like brightness auto-level works.

when you use the vol + (till max) and then press vol- & vol+ again.. doesnt this give you near or 100% volume incall?
 

Mvdbeld

Member
Jan 31, 2011
8
0
Can't install

I can't install the latest version.

I can flash the kernel and get into CWN but when I try to flash .zip I get

"E:Error in /sdcard/FXP119_update-cm-9.0.0-RC0-urushi-UNOFFICIAL-signed.zip
(Status 7)
Installation aborted"

Any suggestions?
 

amodeos

Senior Member
Dec 31, 2011
148
35
surabaya
I can't install the latest version.

I can flash the kernel and get into CWN but when I try to flash .zip I get

"E:Error in /sdcard/FXP119_update-cm-9.0.0-RC0-urushi-UNOFFICIAL-signed.zip
(Status 7)
Installation aborted"

Any suggestions?

Download again...bad files uve downloaded

---------- Post added at 11:04 PM ---------- Previous post was at 11:02 PM ----------

Come on free xperia. We need a theme, i cannt understand what is theme chooser and where to find it and how to use it. Any one will help give the file and explanation.
 

frol8vl

Senior Member
Apr 21, 2012
60
32
found a brightness fix

mediafire.com/?usy001jlh5yrar8
patch from aokp rom by Srkineo
works fine by me:D
 

Mvdbeld

Member
Jan 31, 2011
8
0
Love this ROM clean and fast! Allthough not stable enough for day to day use. Since installing it last night got 2 random reboots (wiped erverything before installing).
 

Griffee

Senior Member
Apr 30, 2012
86
8
Podolsk
Love this ROM clean and fast! Allthough not stable enough for day to day use. Since installing it last night got 2 random reboots (wiped erverything before installing).
That's strange. I have no any reboots. And this ROM is the stabiliest of choise between Sony ICS, MIUI an CM.

Trick with VOL+ - + for low call volume seems to work:rolleyes:
 

Mvdbeld

Member
Jan 31, 2011
8
0
That's strange. I have no any reboots. And this ROM is the stabiliest of choise between Sony ICS, MIUI an CM.

Trick with VOL+ - + for low call volume seems to work:rolleyes:

That's strange indeed, which baseband do you have? I have used the .64 provided in the topic start. Do you have the .70 from stock ICS?

I would love to use this rom all the time but with random reboots it's a no-go for now.
 

Top Liked Posts