Hello,
This is my first post so I'm sorry of I put it in the wrong forum.
I have a Samsung galaxy note 3 SM-N900T (T-Mobile US). It was fresh out of the box.
I followed the tutorial on this site for rooting my specific model, and it got to the rebooting phase and "crashed".
It said:
RECOVERY BOOTING....
RECOVERY IS NOT SEANDROID ENFORCING
Set Warranty Bit : recovery
[/COLOR]about 1:45 seconds later, much longer than the guy in the video said, Odin finally said pass, with a build time of 2:10.
it does not go past that on its own.
The Odin message box is:
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CF-Auto-Root-hltetmo-hltetmo-smn900t.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> recovery.img
<ID:0/006> NAND Write Start!!
<ID:0/006> cache.img.ext4
<ID:0/006> RQT_CLOSE !!
<ID:0/006> RES OK !!
<ID:0/006> Removed!!
<ID:0/006> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
I can trick it into rebooting by unplugging and removing the battery, then booting into modification mode and clicking cancel.
Please help,
Gatt427
(And I did look all over the internet for the answer, and I couldn't find it anywhere)
This is my first post so I'm sorry of I put it in the wrong forum.
I have a Samsung galaxy note 3 SM-N900T (T-Mobile US). It was fresh out of the box.
I followed the tutorial on this site for rooting my specific model, and it got to the rebooting phase and "crashed".
It said:
RECOVERY BOOTING....
RECOVERY IS NOT SEANDROID ENFORCING
Set Warranty Bit : recovery
[/COLOR]about 1:45 seconds later, much longer than the guy in the video said, Odin finally said pass, with a build time of 2:10.
it does not go past that on its own.
The Odin message box is:
<ID:0/006> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CF-Auto-Root-hltetmo-hltetmo-smn900t.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/006> Odin v.3 engine (ID:6)..
<ID:0/006> File analysis..
<ID:0/006> SetupConnection..
<ID:0/006> Initialzation..
<ID:0/006> Get PIT for mapping..
<ID:0/006> Firmware update start..
<ID:0/006> recovery.img
<ID:0/006> NAND Write Start!!
<ID:0/006> cache.img.ext4
<ID:0/006> RQT_CLOSE !!
<ID:0/006> RES OK !!
<ID:0/006> Removed!!
<ID:0/006> Remain Port .... 0
<OSM> All threads completed. (succeed 1 / failed 0)
I can trick it into rebooting by unplugging and removing the battery, then booting into modification mode and clicking cancel.
Please help,
Gatt427
(And I did look all over the internet for the answer, and I couldn't find it anywhere)