[ROM][4.3][OFFICIAL] CM10.2 port for Photon Q

Search This thread

Skrilax_CZ

Inactive Recognized Developer
Dec 20, 2009
1,240
2,398
This is a CM10.2 (Jelly Bean, Android 4.3) firmware for Photon Q. It's not a official CyanogenMod, not supported by the CM team.

Credits: razrqcom-dev-team (epinter, Hashcode, dhacker29, nadlabak, Skrilax_CZ): Photon Q support is by nadlabak and Skrilax_CZ. And of course, CyanogenMod Team.

Disclaimer

Code:
#include <std_disclaimer.h>
/*
 * Your warranty is now void.
 *
 * I am not responsible for bricked devices, dead SD cards,
 * thermonuclear war, or you getting fired because the alarm app failed. Please
 * do some research if you have any concerns about features included in this ROM
 * before flashing it! YOU are choosing to make these modifications, and if
 * you point the finger at me for messing up your device, I will laugh at you.

cm10.2-xda.png


Installation

The proprietary files come from stock JB firmware! It is necessary to flash stock JB first to flash CM10.2!!!

Unlocked bootloader required!!!

1) Download the build and gapps.
2) Boot into recovery
3) Backup your firmware + data !!!
4) Flash CM10.2 (install zip ...)
5) Flash gapps (install zip ...)
6) Wipe data / cache (factory reset)
7) Reboot & Enjoy

To update, just download newer CM10.2 zip file and install it from recovery.

Working

QWERTY keyboard (with multipress)
GSM: Call, SMS, MMS, Mobile Data
CDMA / LTE: Call, SMS, MMS, Mobile Data, 4G
Wifi (network scan may take a long time)
Wifi tethering
USB tethering
Camera (front, back)
Video Camera
HW acceleration
GPS / Glonass
Rotation / Sensors
Torch
NFC
Bluetooth
HDMI (incl. audio)

Not Working

Reading contacts from simcard

Minor Issues

Sometimes back virtual button has wrong icon as if virtual keyboard was out.

Changelog

See http://skrilax.droid-developers.org/cm10.2nightly/razrqcom/changelog.php.

Official builds

Note

The following features are not present in official builds:

- multipress (works only in some apps)
- cardock hack
- 4 key navigation bar setup improvements (being reworked, but still included)
- ability to use SD Card as primary storage

Download

See http://download.cyanogenmod.org/?device=xt897 (GSM) and http://download.cyanogenmod.org/?device=xt897c (CDMA)

Source

See CyanogenMod wiki.

My builds

Download

Nightly builds: http://skrilax.droid-developers.org/cm10.2nightly/razrqcom/
Google apps: http://goo.im/gapps/gapps-jb-20130813-signed.zip

Source

Github: https://github.com/razrqcom-dev-team

Build steps:

Code:
mkdir cm
cd cm
repo init -u git://github.com/razrqcom-dev-team/android.git -b cm-10.2
repo sync
vendor/cm/get-prebuilts

For GSM:
Code:
. build/envsetup.sh && brunch xt897

For CDMA:
Code:
. build/envsetup.sh && brunch xt897c

Notes

1) Any QPST / SPC related things should be done on stock firmware.
2) If you want to ged rid of the "unlocked BL logo", download: http://skrilax.droid-developers.org/xt897/stock_logo.zip, unpack it, reboot the phone to fastboot open command line in the folder and type "moto-fastboot flash logo stocklogo_swapped.bin" to get stock boot logo.
3) If there is a filesystem check it will take a while to get past the CM bootanimation
 
Last edited:

gtownswagga

Senior Member
Oct 27, 2010
72
18
Heads up everyone. You will lose Root Access and have to reroot when installing 4.3 Other than that everything is going good so far. You can root with MotoFail2Go zip tho.
 
Last edited:

hfase

Senior Member
Jan 11, 2013
104
40
hfase.com
First build is up (for GSM, CDMA in a couple of minutes). I havent' tested myself yet, but people for RAZR HD say it's just as useable as CM10.1.

Hey, umm, I feel weird asking but did you need to do anything different to build the source than CM-10.1?
When building mine stops (with errors) at either Focal or Alsa, with "make -i -k" I can't get it to make a flashable zip only the IMG's.
If nothing different, what Java and GCC version are you using?


((As I have said in other posts though, I build from source to save bandwidth, learn, and maybe contribute. :cool: Not to re-brand anybodys hard work.))
 
  • Like
Reactions: Die Bruine

Skrilax_CZ

Inactive Recognized Developer
Dec 20, 2009
1,240
2,398
Hey, umm, I feel weird asking but did you need to do anything different to build the source than CM-10.1?
When building mine stops (with errors) at either Focal or Alsa, with "make -i -k" I can't get it to make a flashable zip only the IMG's.
If nothing different, what Java and GCC version are you using?


((As I have said in other posts though, I build from source to save bandwidth, learn, and maybe contribute. :cool: Not to re-brand anybodys hard work.))
Just this. See http://review.cyanogenmod.org/#/c/46875/ .
 
  • Like
Reactions: hfase

antonyfirst

Senior Member
Jun 15, 2012
193
13
39
Milan
Hey Skrillax, thanks!

Unfortunately, with me, It stays at the boot screen forever.
I have no idea what I should do to make it work.
 

Skrilax_CZ

Inactive Recognized Developer
Dec 20, 2009
1,240
2,398
Well it seems to be a long filesystem check. Give it 4 - 5 minutes first. I'm still on 4.2.2.
 

antonyfirst

Senior Member
Jun 15, 2012
193
13
39
Milan
Hello again: I reached the welcome screen, finally. Unfortunately, there has been a chain of force-closes (never-ending). Should I start it all over or is it better to wait for a few more days?

Thanks again, mate.
 

Skrilax_CZ

Inactive Recognized Developer
Dec 20, 2009
1,240
2,398
I myself will wait until they start rolling nightlies for CM10.2 (at least Nexus 4).
 

pujdo1

Senior Member
Aug 26, 2011
179
10
i am on the nightly from 03.08.2013 cm10.2 gsm version and it is running stable. only 1 force close after first boot and the finishing of the configuration (like languag setup, google acc. etc), this force close is from the clock but only this one time. this was the only fc until now.
the wifi/data/mobile phone connection seems good too.
 

pujdo1

Senior Member
Aug 26, 2011
179
10
How do you you get root back ?

MotoFail2Go zip just hangs
adb phone offline
updating SDK.
got, the allow new computer RSA.
get the files pushed over
then ran-as not found
tried clean install no joy.

how to get root back:

1. Settings --> About Phone --> Tap 7 times on Build-Number. now you should have the deeloper options back.
2. Settings --> Developer options --> Root-Access. select here "Apps & ADB
3. activate USB Debugging.
4. Reboot, finish now you should have root again.
 
  • Like
Reactions: rbeavers

hfase

Senior Member
Jan 11, 2013
104
40
hfase.com
I noticed there are two identical clock apk's included in the systems apps. :/


DeskClock.apk & DeskClockGoogle.apk
 

rebretz000

Senior Member
Jul 11, 2012
1,507
604
Magrathea
When I check my battery uses it shows WiFi on constantly even though I have it turned off.
Anyone else or just me?

Sent from my XT926 using Tapatalk 2
 

Top Liked Posts

  • There are no posts matching your filters.
  • 19
    This is a CM10.2 (Jelly Bean, Android 4.3) firmware for Photon Q. It's not a official CyanogenMod, not supported by the CM team.

    Credits: razrqcom-dev-team (epinter, Hashcode, dhacker29, nadlabak, Skrilax_CZ): Photon Q support is by nadlabak and Skrilax_CZ. And of course, CyanogenMod Team.

    Disclaimer

    Code:
    #include <std_disclaimer.h>
    /*
     * Your warranty is now void.
     *
     * I am not responsible for bricked devices, dead SD cards,
     * thermonuclear war, or you getting fired because the alarm app failed. Please
     * do some research if you have any concerns about features included in this ROM
     * before flashing it! YOU are choosing to make these modifications, and if
     * you point the finger at me for messing up your device, I will laugh at you.

    cm10.2-xda.png


    Installation

    The proprietary files come from stock JB firmware! It is necessary to flash stock JB first to flash CM10.2!!!

    Unlocked bootloader required!!!

    1) Download the build and gapps.
    2) Boot into recovery
    3) Backup your firmware + data !!!
    4) Flash CM10.2 (install zip ...)
    5) Flash gapps (install zip ...)
    6) Wipe data / cache (factory reset)
    7) Reboot & Enjoy

    To update, just download newer CM10.2 zip file and install it from recovery.

    Working

    QWERTY keyboard (with multipress)
    GSM: Call, SMS, MMS, Mobile Data
    CDMA / LTE: Call, SMS, MMS, Mobile Data, 4G
    Wifi (network scan may take a long time)
    Wifi tethering
    USB tethering
    Camera (front, back)
    Video Camera
    HW acceleration
    GPS / Glonass
    Rotation / Sensors
    Torch
    NFC
    Bluetooth
    HDMI (incl. audio)

    Not Working

    Reading contacts from simcard

    Minor Issues

    Sometimes back virtual button has wrong icon as if virtual keyboard was out.

    Changelog

    See http://skrilax.droid-developers.org/cm10.2nightly/razrqcom/changelog.php.

    Official builds

    Note

    The following features are not present in official builds:

    - multipress (works only in some apps)
    - cardock hack
    - 4 key navigation bar setup improvements (being reworked, but still included)
    - ability to use SD Card as primary storage

    Download

    See http://download.cyanogenmod.org/?device=xt897 (GSM) and http://download.cyanogenmod.org/?device=xt897c (CDMA)

    Source

    See CyanogenMod wiki.

    My builds

    Download

    Nightly builds: http://skrilax.droid-developers.org/cm10.2nightly/razrqcom/
    Google apps: http://goo.im/gapps/gapps-jb-20130813-signed.zip

    Source

    Github: https://github.com/razrqcom-dev-team

    Build steps:

    Code:
    mkdir cm
    cd cm
    repo init -u git://github.com/razrqcom-dev-team/android.git -b cm-10.2
    repo sync
    vendor/cm/get-prebuilts

    For GSM:
    Code:
    . build/envsetup.sh && brunch xt897

    For CDMA:
    Code:
    . build/envsetup.sh && brunch xt897c

    Notes

    1) Any QPST / SPC related things should be done on stock firmware.
    2) If you want to ged rid of the "unlocked BL logo", download: http://skrilax.droid-developers.org/xt897/stock_logo.zip, unpack it, reboot the phone to fastboot open command line in the folder and type "moto-fastboot flash logo stocklogo_swapped.bin" to get stock boot logo.
    3) If there is a filesystem check it will take a while to get past the CM bootanimation
    7
    First build is up (for GSM, CDMA in a couple of minutes). I havent' tested myself yet, but people for RAZR HD say it's just as useable as CM10.1.
    6
    Fixed, nightlies rolling again.
    4
    Dhacker and kabaldan fixed the display problems (hanging, etc.) in today's build. kabaldan additionally made a proper patch for audio routing for cardock.
    4
    Official builds are now rolling for cm-10.2, but I'm just too lazy now to expand the first post. :p