This sucks! I seem to have over volted a little to much....
Does anybody have a fix for this?
You'll have to go down to your local shop and put it in a press
[KERNEL] Siyah - JELLYBEAN - ICS [v4.3.3] "One kernel to rule them all!"
- Thread starter ktoonsez
- Start date
You'll have to go down to your local shop and put it in a press
I don't undervolt. I am overvolting. Some time the battery needs a little extra umph to get the CPUs up to speed. Don't be afraid to mess around with your phone. Just take it slow. Hell. I was messing around with 5mV at a time. Just don't get greedy.
Dual boots and mic swaps! =/
Awesome kernel, appreciate the work guys.
Question, I am dual booting AOKP and the new ATT LD3 leak as my secondary. So before I clone LD3 as secondary, is there a mic swap that I can use that wont affect my AOKP build? If I would've flashed the no mic swap kernel, then to my logic, when I flashed the mic swap kernal after restoring my backup, it would have overrode (sp?) it anyways, am I right?
Sounds confusing I know, but the worst case scenario would be to use speakerphone and try to use AOKP as a DD.
P.S.- I tried searching for the phone.apk that was released when the first ICS builds started to show up, but that was a no go. Would that help in my case? If I flashed that apk then flashed the kernel with mic swap with AOKP, would it stick?
Thanks in advance!
---------- Post added at 10:33 AM ---------- Previous post was at 10:31 AM ----------
If it's too complicated, it's ok. I'm not *****in, just wondering if there is a way.
Awesome kernel, appreciate the work guys.
Question, I am dual booting AOKP and the new ATT LD3 leak as my secondary. So before I clone LD3 as secondary, is there a mic swap that I can use that wont affect my AOKP build? If I would've flashed the no mic swap kernel, then to my logic, when I flashed the mic swap kernal after restoring my backup, it would have overrode (sp?) it anyways, am I right?
Sounds confusing I know, but the worst case scenario would be to use speakerphone and try to use AOKP as a DD.
P.S.- I tried searching for the phone.apk that was released when the first ICS builds started to show up, but that was a no go. Would that help in my case? If I flashed that apk then flashed the kernel with mic swap with AOKP, would it stick?
Thanks in advance!
---------- Post added at 10:33 AM ---------- Previous post was at 10:31 AM ----------
If it's too complicated, it's ok. I'm not *****in, just wondering if there is a way.
You cannot dual boot a mic swapped ROM + a non mic swapped ROM.
Both ROM's have to use the same mic setup.
Both ROM's have to use the same mic setup.
Yes they are going to conflict, there is only 1 kernel for both ROM's. You need a modded phone.apk for one of them so they both need the same "swapage".
Damn, that was quick! Haha I appreciate the reply bro. It's no biggie. The only reason I'm using LD3 is for Samsung Media Hub
How do I forgot my Internal SD Card? I'm running Siyah and when I go to mounts and storage and try to mount /sdcard it tells me can't mount.
I have everything important backed up on my external sd.
EDIT: Nevermind, instead of doing it through siyah recovery i just did it through the storage option in settings. Seemed to do the job fine. Thanks anyway.
I have everything important backed up on my external sd.
EDIT: Nevermind, instead of doing it through siyah recovery i just did it through the storage option in settings. Seemed to do the job fine. Thanks anyway.
Last edited:
Slow speeds? Try a different modem. Check apn settings. Toggle airplane mode. You're not being very descriptive which is making me want to bash my face into a brick wall.
Sent from my SGH-I777 using Tapatalk 2
After reading your previous posts do a full wipe. If that doesn't work go get a new iPhone and send me your sgs2
Sent from my SGH-I777 using Tapatalk 2
I hope your face is okay.
Thought you all would like to know...been running 3.1 with omega 9 with no problems...actually runs better than entropys with omega
Sent from my SGH-I777 using XDA
Sent from my SGH-I777 using XDA
Had a really odd issue. I updated my psychomantis foxhound rom with the v. 3.1rc2 and right after flashing I rebooted the recovery and my screen went nuts. My phone had a ****load load of black and white lines all over the place. What I had to do was hold the power and volume down/up bottons to get it to reboot and after the reboot everything seems fine. But that was the strangest lock up I've ever seen! The screen of my phone looked like a tv broadcasting static. Thought for sure my phone was shot when I seen that happen. Luckily it wasn't.
I have seen that a few times too. It seems to be when you flash Siyah on top of another kernel, what I did was touch the screen anywhere and it rebooted on its own just fine.
Yeah its really odd and my phones screen looked like the TV from the movie poltergeist lol they're here
One thing though I was already running a siyah kernel just updated to the newest one.
Last edited:
Yeah its really odd and my phones screen looked like the TV from the movie poltergeist lol they're here
One thing though I was already running a siyah kernel just updated to the newest one.
Not if you flashed a ROM (foxhound) before siyah, that would have flashed a kernel and then you went on top of it. Thats what triggers it for some reason.
I wants RC4 now....
Patience young grasshopper.
Sent from my SGH-I777 using Tapatalk 2
Hi ktoon,
I hope the logs helped fix the freeze bug. I'm looking forward to your next update
Thanks!
Sent from myphone.
I hope the logs helped fix the freeze bug. I'm looking forward to your next update
Thanks!
Sent from myphone.
I have a question regarding Overclocking with this kernel on task's AOKP. AOKP has a built in Performance Overclocker in ROM Control. Can I use that to set the Max CPU and have it set on boot? Or do I need to use SetCPU to OC?
Also, in AOKP, there is an option for Fast Charge in the performance settings. I know that it will only work if the kernel supports it, does this kernel support it? If so, what exactly does fast charge do? Are there any negative effects?
BTW: I have been running RC2 on AOKP build31(now32) for 2 days and I have not experienced a freeze or random reboot.
Also, in AOKP, there is an option for Fast Charge in the performance settings. I know that it will only work if the kernel supports it, does this kernel support it? If so, what exactly does fast charge do? Are there any negative effects?
BTW: I have been running RC2 on AOKP build31(now32) for 2 days and I have not experienced a freeze or random reboot.
Last edited:
Fast Charge: I don't think anyone here uses it. Since your phone cannot charge any faster than 650ma, I am guessing it just increases the USB charging to that (dangerous) and turns off any data.
I myself use the build in ROM Control for clocks/volts, works great. I don't notice any slowness with 1000Mhz.
Similar threads
Top Liked Posts
-
There are no posts matching your filters.
-
340The wait is over, Siyah v4 for the I777 is finally here!
Full credit of course goes to Gokhanmoral. Go thank him for creating this great fully customizable kernel RIGHT NOW!!!
This kernel is built from Gokhanmoral's Sources
with some tweeks to make everything run smoothly on our I777's
Click "Thanks" if you like what you see or donate with my link.
Install Instructions
1. Wipe cache
2. Wipe dalvik
3. If you are already on a previous version of Siyah, "Reset ExTweaks profiles" (its under "Kernel specific options")
4. Flash the kernel
5. Reboot and enjoy
It wont hurt your phone at all if you go with the wrong one and only takes a minute to flash the other.
Change Log and Dual-boot ROM instructions in Post #2. READ THE ENTIRE POST #2 BEFORE DOING ANYTHING WITH THE DUAL-BOOT!!!
KEY FEATURES
ROMS VERIFIED WORKING
Here is a link to my sources for those that couldn't find it :good:
https://github.com/ktoonsez/siyahkernel3
DON'T FLASH ANY FILES FROM THE LINK BELOW, JUST FOR CHANGELOG INFO AND CREDIT!!!584.1beta5 Change Log
■Fix permissions issue causing crashing on bott with certain Sammy ROM's
4.1beta4 Change Log
■Linux 3.0.40
■CWM-Based Touch Recovery v6.0.1.1
■fixed led timeout not being saved
■new GPU frequency steps: 54, 108, 133, 160, 266, 330, 400, 440, 520MHz (Removed in beta4)
■added one more GPU step, we now have 4 GPU steps with 108, 160, 266, 330MHz defaults. (Removed in beta4)
■added ntt docomo gps support again (ntt-docomo users can use their previous scripts to get gps working)
■fixed movfilter not being changed with kmemhelper (should fix touch sensitivity problems)
■removed 25MHz and 50MHz CPU steps
■fixed led activity on brightness change
■ExTweaks settings will be reset because of GPU changes. if you revert back to a previous version make sure you reset ExTweaks settings manually.
■update beta1 -> beta4: fixed gamma shift not working in ExTweaks. removed all gpu modifications to make sure we have no problems with other parts. some users (including me) experienced no problems with new gpu steps whereas some users had kernel panics when the screen is off. Consider v4.1beta4 as 4.0.2 with linux 3.0.40 and cwm-based recovery 6.0.1.1.
3.5 Change Log
■bluetooth: support for 4.0.4 stock ROMs
■Whole butt load of merges from Tungstwenty
3.4.4 Change Log
■pegasusq fixes and tweaks
■added cfs tweaks settings to ExTweaks (samsung default, linux kernel default and thunderbolt script defaults)
■added Tungstwenty’s implementation that let’s us see deleted wakelock details (optional in ExTweaks)
■cherry-picked some wifi changes/fixes from cm9 repo
■added mdnie negative effect toggle to ExTweaks (by Tungstwenty)
■and some other tiny changes…
■Linux 3.0.36
■removed some potentially unsafe changes which might be the reason of some users having problems with the latest release.
■added ntt device gps support back. removed exfat related mess. added Entropy512′s patch to prevent multicast packets for added headphone amplification setting to extweaks (named it soundgasm). fixed data statistics and some other changes in config and sources…
3.4.3 Change Log
■Linux 3.0.36
■Several USB fixes
■NFSv4 issues addressed
■Fix overlapping static i/o mappings
3.4.2 Change Log
■Linux 3.0.35
Dual-Boot instructions and Notes
If you want to have another ROM as secondary ROM, follow these steps:
1.Make a nandroid backup of your existing ROM
2.wipe everything and install the other ROM
3.Boot the ROM and make customizations. Don’t forget to reflash SiyahKernel if the ROM flashes another kernel.
4.Use CWM Touch Recovery to clone your rom as secondary rom.
5.Restore nandroid backup
6.To boot from the secondary ROM, either press the HOME key or the VOLUME DOWN key when prompted.
Some notes about dualbooting:
■If you do not make any cloning you won’t be prompted to boot the second ROM.
■you may need to reflash this kernel after a nandroid restore if your nandroid backup is created with another kernel.
■you won’t be able to use mass storage mode for /sdcard in second rom because we have our data and cache partitions on /sdcard. only external sdcard will be mounted if you are using mass_storage mode. mtp should work fine for sdcard.
■once again, you won’t be able to flash any CWM flashable zip to second ROM.
More good information on dual-boot
http://xdaforums.com/showpost.php?p=24724563&postcount=329628OP Updated:
Download v3.2.7.2 - CWM Flashable
IF YOU CAN'T DOWNLOAD THE FILES, USE "REQUEST DESKTOP SITE" OPTION IN YOUR BROWSER!
IF YOU DON'T KNOW HOW TO "REQUEST DESKTOP SITE" GO AWAY, U HAVE NO BUSINESS FLASHING ANYTHING, LET ALONE A KERNEL!
WITH mic swap (use this one if you are using a ROM directly from the I9100 forum, AOKP or CM9)
http://www.mediafire.com/?4ac2u03hg2gg26x
WITHOUT mic swap (use this one if you are using a ROM from OUR I777 forum like UCPLCx or anything based on these)
http://www.mediafire.com/?lx2x9adlgbja7ih25OP Updated
Change Log 4.3.1
1. Status 7 should be gone
2. wakelock: use single threaded workqueueus
3. Lots of "linux/audit" patches
4. Lots of block pathes/updates
5. A butt-load of PM / Sleep mods
6. wireless driver to 1.28.11.9 from Korean S3 BIG TNX to GM (For JB-MALI user)
7. Merged in Linux 3.0.45 and .46 stuff
8. And Im spent
