acejavelin
Inactive Recognized Contributor
Yes, it should... Read the other Soff thread in this section about rumrunner.
Sent from my Nexus 4 using Tapatalk
Yes, it should... Read the other Soff thread in this section about rumrunner.
Sent from my Nexus 4 using Tapatalk
thanks so much for the help i managed to get this out on 2 of my friends rezounds and put 4.3 on them for the time being since 4.4 is still tweaky thanks for all the helpCurrent rumrunner universal, 0.5.0 I think... Just make sure ADB is enabled and root is functioning.
Sent from my Nexus 4 using Tapatalk
thanks so much for the help i managed to get this out on 2 of my friends rezounds and put 4.3 on them for the time being since 4.4 is still tweaky thanks for all the help
Can you can give some details on how you achieved s-off? I've followed every guide I could find with zero luck. Thanks.
Can you can give some details on how you achieved s-off? I've followed every guide I could find with zero luck. Thanks.
Please remove links...windows control bear for anyone looking for it. I used it on a 32 bit xp machine so i don't know if its 64 bit compatible and what not.
Prerequisites said:Prerequisites
In order to use JuopunutBear you must meet the following pre-requisites:
Be unlocked using the HTCdev bootloader unlock
Be rooted (have superuser and/or an unsecured boot image installed)
Have a spare microSD card, or to have backed up all contents of your SDcard
Have fastboot and adb drivers installed and working (windows)
Have usb debugging enabled
Have a legth of insulated wire of sufficient length to join the contact points for your device. See images and videos for device specific information.
Instructions said:Instructions
(Optional) Perform a full backup and replace your sdcard with one that you are willing to wipe.
Ensure that your battery is fully charged.
Choose the correct download for your device and operating system
Extract the zip file to a new directory
Verify the MD5 checksum for your download
Read and/or watch the video for the device specific information for your device
Run controlbear as admin(windows) or root or using sudo on linux
Follow the on-screen instructions from ControlBear
Do not press any of the buttons on the phone during the process.
After doing the “wire-trick” yor phone will reboot. The sequence of the reboot may vary somewhat from that you see in the videos as these were taken during various stages of development.
If you see the following message from ControlBear after doing the wire trick:
ErrorMsg: Still sober.
This means that you have been unsuccessful in implementing the wire-trick. Run ControlBear again.
The usual casue for this is that you failed to perform 2 clean contacts or mistimed the wire trick.
Your phone will reboot several times during the process, this is normal. ControlBear will tell you when it has finished whether sucessfully or not.
Wire Trick said:Wire Trick
The “wire trick” is an essential part of the JuopunutBear S-OFF procedure.
When instructed to do so by the program you must perform the “wire trick” which is done as follows.
Obtain an insulated wire of appropriate length and gauge
Insert one end of the wire into the hole where pin 1 is indicated in the picture below, ensuring that a firm contact it made with the metal contact at the bottom of the hole
Briefly touch to other end of the wire to the contact marked GND in the picture below.
Wait approximately 1.75 seconds and then again touch the wire to the marked GND.
Allow the program to continue.
Note: it may take several attempts of running the program in order to obtain the correct timing for the wire trick.
The contact points for the “wire trick” are shown in the picture below.
Fix for external SD is as follows:
- Install busybox
- adb shell busybox fdisk /dev/block/mmcblk1
- type o
- type w
- adb shell busybox fdisk /dev/block/mmcblk1
- type n
- select primary, then 1
- chose default sizes
- type w
- adb shell busybox mkfs.vfat /dev/block/mmcblk1p1
For those of you having problems with internal storage, my apologies. We accidentally included the GB hboot.
Download this:
http://dl.dropbox.com/u/14779955/jb_hboot.zip MD5: b05336c08f709bf0a909205bcb95b951
Put the phone in fastboot mode, then run the follwoing commands:
Code:fastboot oem rebootRUU fastboot flash zip jb_hboot.zip fastboot reboot
Ignore the green bar.