Yup it does... Booted just fine too... I'm not going to ask... On the positive side it only took me one try
Congrats
Yup it does... Booted just fine too... I'm not going to ask... On the positive side it only took me one try
For those having the issue in windows with the keyboard not recognized while getting the external card working.
Type: adb shell
then go through the rest of the commands. Those with SU already have busybox installed most likely, especially if on custom roms. Anyway, that worked for me. When going directly to busybox fdisk, I had the same keyboard issues.
I keep getting
/data/local/Juopunutbear not found
Press enter to exit
now all i need is someone to reupload the stock gb ruu cause i have the crappy ics leak radios and i just wanna be stock as i can be.
I had run into pretty much every problem you can seem to get into with this S-Off method. I recommend having a micro sd card reader. Sound like you need to format your SD then try again.
EDIT: Anyone working on a detailed tutorial for S-Off? Thinking of writing one up that's a bit more descriptive then what was provided to us.
Sent from my Htc Rezound
Follow me on twitter @lmrtech
EDIT: Anyone working on a detailed tutorial for S-Off? Thinking of writing one up that's a bit more descriptive then what was provided to us.
Sent from my Htc Rezound
Follow me on twitter @lmrtech
Same thing happened to me. After I got S-Off I just had to reinstall a RUU and it worked fine again, no amount of formatting would work otherwise. Hope this helps.
Yes - I still had mine from a bit back and I'm glad I did.
Here's some versions that may help for now: http://www.scottsroms.com/downloads.php?do=cat&id=11
anyone wanna try and help me out with this quick? I was stuck on 'waiting device' for a long time. After searching someone said to pull battery, boot into rom, and run control again. I did this, but cannot boot into my ROM. Any help is appreciated
What kind of wire can I use? Can I cut an old power cord up???
Sent from my ADR6425LVW using Tapatalk 2
Any wire will work. I used some old headphones. Just make sure you're getting good contact with the points
Sent from my ADR6425LVW using Tapatalk 2
Paper clip with electrical tape?
Sent from my ADR6425LVW using Tapatalk 2
You will have to flash the kernel or boot.img again
Sent from my ADR6425LVW using Tapatalk 2
Prerequisites said:Prerequisites
In order to use JuopunutBear you must meet the following pre-requisites:
Be unlocked using the HTCdev bootloader unlock
Be rooted (have superuser and/or an unsecured boot image installed)
Have a spare microSD card, or to have backed up all contents of your SDcard
Have fastboot and adb drivers installed and working (windows)
Have usb debugging enabled
Have a legth of insulated wire of sufficient length to join the contact points for your device. See images and videos for device specific information.
Instructions said:Instructions
(Optional) Perform a full backup and replace your sdcard with one that you are willing to wipe.
Ensure that your battery is fully charged.
Choose the correct download for your device and operating system
Extract the zip file to a new directory
Verify the MD5 checksum for your download
Read and/or watch the video for the device specific information for your device
Run controlbear as admin(windows) or root or using sudo on linux
Follow the on-screen instructions from ControlBear
Do not press any of the buttons on the phone during the process.
After doing the “wire-trick” yor phone will reboot. The sequence of the reboot may vary somewhat from that you see in the videos as these were taken during various stages of development.
If you see the following message from ControlBear after doing the wire trick:
ErrorMsg: Still sober.
This means that you have been unsuccessful in implementing the wire-trick. Run ControlBear again.
The usual casue for this is that you failed to perform 2 clean contacts or mistimed the wire trick.
Your phone will reboot several times during the process, this is normal. ControlBear will tell you when it has finished whether sucessfully or not.
Wire Trick said:Wire Trick
The “wire trick” is an essential part of the JuopunutBear S-OFF procedure.
When instructed to do so by the program you must perform the “wire trick” which is done as follows.
Obtain an insulated wire of appropriate length and gauge
Insert one end of the wire into the hole where pin 1 is indicated in the picture below, ensuring that a firm contact it made with the metal contact at the bottom of the hole
Briefly touch to other end of the wire to the contact marked GND in the picture below.
Wait approximately 1.75 seconds and then again touch the wire to the marked GND.
Allow the program to continue.
Note: it may take several attempts of running the program in order to obtain the correct timing for the wire trick.
The contact points for the “wire trick” are shown in the picture below.
Fix for external SD is as follows:
- Install busybox
- adb shell busybox fdisk /dev/block/mmcblk1
- type o
- type w
- adb shell busybox fdisk /dev/block/mmcblk1
- type n
- select primary, then 1
- chose default sizes
- type w
- adb shell busybox mkfs.vfat /dev/block/mmcblk1p1
For those of you having problems with internal storage, my apologies. We accidentally included the GB hboot.
Download this:
http://dl.dropbox.com/u/14779955/jb_hboot.zip MD5: b05336c08f709bf0a909205bcb95b951
Put the phone in fastboot mode, then run the follwoing commands:
Code:fastboot oem rebootRUU fastboot flash zip jb_hboot.zip fastboot reboot
Ignore the green bar.