I have set the max speed to 1400 MHz, and by mistake I have set it to load this values on start.
Now I'm into a bootloop. Is there any way of restore the maximum speed to 1000 MHz.
Any help will be appreciated.
Try to flash another kernel!
I have set the max speed to 1400 MHz, and by mistake I have set it to load this values on start.
Now I'm into a bootloop. Is there any way of restore the maximum speed to 1000 MHz.
Any help will be appreciated.
New google apps !
http://goo.im/gapps/gapps-ics-20120429-signed.zip
Sent from my Nexus S using Tapatalk 2
Was CM9 your first ICS ROM? This is pretty typical for ICS unfortunately. If you have an old efs backup (as close as possible to when you got the phone) you can replace the files (and set the right permissions) and it should stop doing that. ICS doesn't play with efs as nice as GB did. There's another thread all about efs shenanigans; I don't have the link off hand.
Sent from my Nexus (IC)S
Here you go: http://xdaforums.com/showthread.php?p=17587351
Note: when you get to the step where it mentions ".nv_data.bin"; on the NS there's no '.' in front, so just "nv_data.bin"
Otherwise see thread for more info.
Sent from my Nexus (IC)S
ok, i'll read the topic.
CM9 wasn't my first ICS, infact before flash CM9 i flashed official ICS 4.0.3 for getting the latest bootloader/radio.
and i haven't specified before, but my IMEI isn't corrupted or changed to 00xxx
Settings for SetCPU if you need a performance and battery balance. Im using CM9 v7, Matr1x v19 cfs, latest gapps. Using a custom launcher with around 30 apps installed (all games and browsers..etc facebook, viber, angry birds...etc). wifi, 2g/3g on, deep idle off. Im at 50% right now with light use and thats awesome. 12 hrs already.
Main: 1000max 200min lulzactive, default values for governor and voltages.
Profile:
Screen off: 800max 200min interactivex Priority 60
Charging Any: 1460max 1200min performance Priority 50
Battery <20% 400max 200min interactivex Priority 40
Battery <50% 800max 200min interactivex Priority 30
You may want to stay away from using 100mhz during screen-off or screen-on states for three reasons 1) It seems 100 mhz uses more power than 200 mhz. According to tests, 100 mhz accounted to 1 W / GHz and 200 mhz to 0.7 W / GHz, when both the cores were online. 2) 200 mhz can finish same task faster compared 100 mhz and thus hit deep idle soon. 3) 200 mhz is the 'sweet spot' of frequency in SGS II. ie, the frequency used in the calculations based on the optimal energy to run (Ex: In Milestone it's 550 MHz). So , 'energetically efficient' frequency for our CPU is 200 mhz.
http://xdaforums.com/showthread.php?t=1369817
Anyone else have their preferred settings? Do put in mind that all phones are different and none are the same. This may work verywell for me but it may be completely different for you. Use Safemode in SetCPU help page http://www.setcpu.com/documentation.html#safe_mode. Also make a nandroid back up. I highly encourage you to play around with these settings to get the best out of your phone. BUT ONLY IF you do a nandroid back up and untick set on boot. Oh and there is no way you can really fck this up (mind the language) if you have nandroid backup, untick set on boot, safemode via SetCPU Page. If you get bootloops on a unstable frequency/voltage, just reflash your rom via recovery.
Safe Mode
If you're trying out new CPU speeds on an overclocked kernel or trying out new voltage settings, it's always a good idea to uncheck the Set on Boot checkboxes in the corresponding menus before doing so. This way, your phone will not boot loop if you get stuck on an unstable CPU frequency or voltage. To be safe, you can extract a Safe Mode update.zip to your SD card in the Main tab. Access the menu here, and press Safe Mode Instructions to do this. Flash the setcpu_safemode_toggle.zip file in recovery mode as a normal update.zip to recover if SetCPU causes your device to boot loop. Flash the zip again to toggle safe mode off. Alternatively, you can make a file called setcpu_safemode with no extension and place it on your SD card or internal storage, /data, or /data/local to active safe mode.
If you didn't get a chance to extract the safe mode zip, download the safe mode update.zip here. Flash it in recovery mode just like any other update.zip.
http://www.setcpu.com/documentation.html#safe_mode
Then your EFS is fine don't touch it!
Unless your IMEI goes to 00xxx ignore anything in the log, it doesn't matter
Sent from my ice cream powered Nexus S
yesyes, this is the rule,
but i'm curious and want to know more ....
Is this a common issue?
Blue signal bar on Wi-Fi
Gray signal bar on 3G
It started four or five days ago. I tried reflashing gapps, ROM, both or just one but I still get gray bar when on data. Is it my network provider ?
When on data, sync doesn't seem to work perfectly like push from Gmail. Last ROM I flashed and currently using is nightly 20120427 and 20120429 gapps
Thanks for the quick responseBE sure you're not using any 3th part data limiter as firewalls, etc. The grey color says data is connected, but somehow limited (protocols, address, ips etc)
Sent from my Nexus S using XDA
Is this a common issue?
Blue signal bar on Wi-Fi
Gray signal bar on 3G
It started four or five days ago. I tried reflashing gapps, ROM, both or just one but I still get gray bar when on data. Is it my network provider ?
When on data, sync doesn't seem to work perfectly like push from Gmail. Last ROM I flashed and currently using is nightly 20120427 and 20120429 gapps
#include <std_disclaimer.h>
/*
* Your warranty is now void.
*
* I am not responsible for bricked devices, dead SD cards,
* thermonuclear war, or you getting fired because the alarm app failed. Please
* do some research if you have any concerns about features included in this ROM
* before flashing it! YOU are choosing to make these modifications, and if
* you point the finger at me for messing up your device, I will laugh at you.
*/
Old Version: V6 patch 0Night Builds can be found here: http://get.cm/?device=crespo ChangeLog: http://cm-nightlies.appspot.com/?device=crespo
NEW on alfa 14:ROM: http://bit.ly/CM9Alfa14
GAPPS: http://download.clockworkmod.com/test/gapps-ics-20111128.zip
Those files are not compatible with Alfa 15 and up
I flashed nightly 0520 and noticed there wasn't any Facebook sync/errors out. Anyone else notice that? Just curious.
Also, kalim, where's 8.0?