I am holding the buttons before plugging in and Im holding while plugged in, I still get the error..
[RECOVERY][APP] 4-28 One-Click NvFlasher ClockWorkMod Touch 5.8.1.3/5.0.2.0/4.0.1.5
- Thread starter TGA_Gunnman
- Start date
-
- Tags
- development
I am holding the buttons before plugging in and Im holding while plugged in, I still get the error..
Don't unplug the usb cable until after it is done flashing....it should say something was successful and hit any key to close promt....hit the key and then you can unplug the usb cable right away our wait a minute or two then unplug it
Sent from my G2X
Sent from my G2X
===============================================================
One Click ClockWorkMod Recovery Flash for T-Mobile G2x
===============================================================
===============================================================
Nvflash started
USB device not found============================================================
===
===============================================================
*****Once nvflash has completed successfully then hit any key to close.*****
****If any step failed then repeat the process****
Press any key to continue . . .
This is the exact message I get and Im holding the volume buttons in prior to plugging in and I get this message while still holding the buttons in and the battery is removed.
One Click ClockWorkMod Recovery Flash for T-Mobile G2x
===============================================================
===============================================================
Nvflash started
USB device not found============================================================
===
===============================================================
*****Once nvflash has completed successfully then hit any key to close.*****
****If any step failed then repeat the process****
Press any key to continue . . .
This is the exact message I get and Im holding the volume buttons in prior to plugging in and I get this message while still holding the buttons in and the battery is removed.
Time for a trip to tmobile for an exchange. Just tell them it locked up, you rebooted it and its in a boot loop. What happened to get it in boot loop? What did you do?
Sent from my T-Mobile G2x
I tried to flash a theme with rom manager and then it went into a bootloop..
I dont think its finding your device because there is something wrong with your bootloader. So the apx driver is not installing to a device. What does device managet say when you connect yhe phone holding buttons. Do you see the device under usb section. Nvidia apx device?
Sent from my T-Mobile G2x
Sent from my T-Mobile G2x
'NVIDIA USB Boot-recovery driver for mobile devices'.
I see this when I hold the volume buttons and plug in my phone without the battery installed..
I really appreciate your help..
Thats correct driver. And at that point you push to flash and nadda. What recovery are you choosing? Try test2
Sent from my T-Mobile G2x
Sent from my T-Mobile G2x
hey i did all the steps correctly and everything seemed like it all went well but when i tried to get into ClockWorkMod Recovery by pressing the volume down and power button till i saw the orange android but all that came up was a box with an arrow and this wiped my whole phone what happend here?
@TGA_Gunnman
literally just woke up and it hit me,
why don't you hard-code it flash a file named "recovery-image.img" and in the OP provide links to all of the available recovery images (test2, stock, 3.0.2.7) and edit instructions to download the recovery image they want to NVFlash, rename to "recovery-image.img", place in the NVFlash folder, fire up the program, click on a button named "Use NVFlash to flash recovery-image.img"
That way you have to update the program a LOT less and it becomes more versatile to flash alternate recoveries
Let me know what you think brah
literally just woke up and it hit me,
why don't you hard-code it flash a file named "recovery-image.img" and in the OP provide links to all of the available recovery images (test2, stock, 3.0.2.7) and edit instructions to download the recovery image they want to NVFlash, rename to "recovery-image.img", place in the NVFlash folder, fire up the program, click on a button named "Use NVFlash to flash recovery-image.img"
That way you have to update the program a LOT less and it becomes more versatile to flash alternate recoveries
Let me know what you think brah
Trying to understand something.. a learning moment.
When rooting, there is the LGDriver.. and then there is a separate driver for flashing cwm.. Rooting and flashing are not both compatible w/ one driver or the other?
Let's say I recover using the stock recovery or my own nandroid backup.. either way, I will still be rooted after the recovery? Then I just have to repeat your process, with the driver that is already setup.
So if I'm understanding this correctly, the only time the LGDriver would come back into play is if I restored a backup and then needed to unroot the phone?
When rooting, there is the LGDriver.. and then there is a separate driver for flashing cwm.. Rooting and flashing are not both compatible w/ one driver or the other?
Let's say I recover using the stock recovery or my own nandroid backup.. either way, I will still be rooted after the recovery? Then I just have to repeat your process, with the driver that is already setup.
So if I'm understanding this correctly, the only time the LGDriver would come back into play is if I restored a backup and then needed to unroot the phone?
Similar threads
Top Liked Posts
-
There are no posts matching your filters.
-
268
Procedure:
If you came here first, go here and read the getting started before flashing this recovery: GETTING STARTED GUIDEhttp://xdaforums.com/showthread.php?t=1060715
This process consists of 2 steps.
1. Install the windows driver.
2. Flash the Recovery using the OneClick App.
*** You will need to have .Net Framework 2.0 or above installed. ***
_________________________________________________________________________________________________
VIDEO:
- You can watch a Video provided for us by the UnLockr for a walk-through of how to use the One-Click ClockworkMod Recovery Flasher. (Thanks Dave!)
Click on The UnLockr Image to watch the video:(Video is no longer relevant pertaining to entering recovery from boot. And the buttons you can click.)
_____________________________________________________________________________________________________________________________________________
One-Click ClockworkMod Recovery NvFlasher
****Warning I am not responsible if you brick your phone!****
Instructions:
Nvidia NvFlash APX Driver
- Unlike a lot of Android phones out there the Nvidia Tegra2 chipset require additional drivers in Windows to support low level flashing.
Install APX Windows driver from APX folder.
(Windows x86 and x64 O/S Drivers):
****If you are running VmWare kill it.****
- Remove the battery.
- Plug in your USB cable to your PC.
- Hold Volume Up and Volume Down at the same time keeping them held down.
- Plug in the USB cable to your phone. (Keep the buttons held until Windows detects a new APX device.)
- Open Device Manager in Windows and you should see "APX Device" listed with an error icon.
- Right click on the APX device.
- Select 'Update driver software'.
- Select 'Browse my computer...'.
- Select 'Let me pick...'.
- Select 'Have disk'.
- Browse to directory you extracted the *driver* software to: One-Click-G2x-recovery-flasher-04-28-12\APX.
- Accept any warnings, including the big red alert (you may need to disable UAC).
- Now in Device Manager under 'USB Controllers' you should have an 'NVIDIA USB Boot-recovery driver for mobile devices'.
- If not, uninstall the driver, reboot, rinse and repeat.
Flash ClockworkMod Recovery
- Remove the battery.
- Goto NvFlash directory and Double Click "OneClickRecoveryFlasher.exe".
- Make sure the USB cable is unplugged from your phone.
- Hold Volume Up and Volume Down at the same time keeping them held down. (Keep them held until you see the "S/W Upgrade" screen on your phone after you complete step7!).
- Plug in the USB cable to your phone.
- Click the "Flash CWM" button of your choosing. If you own a External SD card I suggest to choose version 5.0.2.0. This gives you Internal and External SD Support for ROM flashing but has External SD Nandroid Backup Support Only! If you do not own a External SD Card choose version 4.0.1.5 what has full Internal SD support for flashing ROMS and Nandroid backup.
- You should see it send a bunch of files to the device and the phone screen should say "S/W Upgrade - Please wait while upgrading...". Once the files are sent and the program is finished running in the command window, you can just pull the USB cord while it still says "S/W Upgrade - Please wait while upgrading...".
- Put the battery back in and you can now boot into Recovery. (see below..)
Booting into ClockworkMod Recovery
- Power off your phone.
- Hold Vol Down + Power.
- Keep holding them, as soon as you see a "Blue LG Graphic" logo let go of the buttons.
Restore LG G2x Stock Recovery
- Flash Stock recovery only when you want to send your phone in to T-Mobile. Otherwise do not flash Stock recovery. Stay on ClockworkMod Recovery.
- Remove the battery.
- Goto NvFlash directory and Double Click "OneClickRecoveryFlasher.exe".
- Make sure the USB cable is unplugged from your phone.
- Hold Volume Up and Volume Down at the same time keeping them held down. (Keep them held until you see the "S/W Upgrade" screen on your phone after you complete step7!).
- Plug in the USB cable to your phone.
- Click the "Flash Stock" button.
- You should see it send a bunch of files to the device and the phone screen should say "S/W Upgrade - Please wait while upgrading...". Once the files are sent and the program is finished running in the command window, you can just pull the USB cord while it still says "S/W Upgrade - Please wait while upgrading...".
- Put the battery back and you are done.
654ClockworkMod Version 4.0.0.2 is now apart of One-Click-App. I had to do a quick piecemeal on my laptop since i am out of town looking for a house, buying a house and moving. Don't worry about the file versions in the dir. It is 4.0.0.2, I tested it.
Feel free to flash right on top of existing versions.
Sry for the delay.
Have fun! - You can watch a Video provided for us by the UnLockr for a walk-through of how to use the One-Click ClockworkMod Recovery Flasher. (Thanks Dave!)
