Teclast X98 3G - 9.7" Retina 22nm Intel x64 Bay Trail Android tablet

Search This thread
By:
Advanced…
A

avich

Member
Oct 16, 2010
19
9
GTA
I could not find this tablet mentioned anywhere on XDA, so I've decided to create this thread for sharing impressions and useful information between owners and anyone interested.

x983g_zt_01.jpg


Manufacturer's page:
http://www.teclast.com/en/zt/x983g/


Specifications:
  • CPU: Intel Bay Trail-T 3735D 64bit, 22nm, 1.3(turbo 1.83)GHz
  • RAM: 2GB (DDR3L)
  • ROM: 32GB eMMC Flash
  • Display: 9.7 inch IPS 2048x1536
  • Camera: 2MP front / 5MP back (AF)
  • Radio: 802.11b/g/n, GSM+WCDMA, GPS, BT 4.0, WiDi
  • Connectivity: mkHDMI, mkUSB/OTG, mkSDXC
  • Battery: 8500mAh

MSRP: 1299CNY (approximately $210US).

First impressions
Fast, responsive, light, crisp and bright
Several Chinese apps. Some of them installing other Chinese apps. (removed/disabled, except for tUI and TeclastAutoUpdater)
No Apps drawer. no widgets - Apple-like UI. (Apex Launcher installed)
Overall feeling of money well spent :D

Current problems
I've found two things that I don't like about the tablet:
First, the speakers. I can't complain about sound - there's some bass, highs are clear, overall quality is good. But it eludes me why would someone place two speakers on the same side?
Second, and hopefully, temporary one, is the battery meter. From 0% it goes to 100% in about 20 minutes (BTW, the tablet pulls 2A out of the bundled PSU), says "charging 100%", for few hours more the current is still 2A, then 1.5A for some time, then 1A (somewhere here its starts to say "Charged"), and after 8 hours, when the current was 0.2A, I've disconnected the cord. "Bleep! Connect the charger! 10%" :eek: After an hour of use, I turned it of, then on... 77%! Went down to 8% after an hour more, then to 7% in another hour... :silly: A firmware update is definitely needed here. BTW, in 2 days I own the thing, I've had 2 updates, so the manufacturer's developers are doing something.

--- Update 2014-08-01

I've got the POWER!

The bad news are - (1) technical support does not answer emails, at least in my experience.. Probably because of language difficulties, maybe they have some other reasons. (2) replacement batteries are hard to find - on ali express I found only one seller who claims his batteries are 12Ah. The good news is - I did not need all of that. Finally, I've decided to open the thing up and check all accessible connection points.

Disassembly
You'll need a sharp tool (there are special plastic tools, but I used regular small knife to start, and a plastic one from ikea to widen and crack on the initial opening). Back cover is snapped on over the screen base on small latches, and all you need to do is slit the groove that goes around the screen a little, then go on unlatching until it comes apart. The groove is just around the screen, between two plastic parts, not around the metal cover.
All I needed to do was tracking the battery wire, lifting black tape, and re-plugging the wire in its place. Full battery power is now restored. Feeling are mixed -- :D or :( ?
 
Last edited:
  • Like
Reactions: jclu52, marek7400 and Valerio191
G

garryweil

Member
Aug 27, 2010
18
1
Portland
thanks for review

I have been looking to buy this tablet, where did you buy it from?
Thanks
 
Last edited by a moderator:
J

jhnchristopher

New member
May 11, 2014
2
0
Thanks for the review

avich said:
I could not find this tablet mentioned anywhere on XDA, so I've decided to create this thread for sharing impressions and useful information between owners and anyone interested.




Specifications:
  • CPU: Intel Bay Trail-T 3735D 64bit, 22nm, 1.3(turbo 1.83)GHz
  • RAM: 2GB (DDR3L)
  • ROM: 32GB eMMC Flash
  • Display: 9.7 inch IPS 2048x1536
  • Camera: 2MP front / 5MP back (AF)
  • Radio: 802.11b/g/n, GSM+WCDMA, GPS, BT 4.0, WiDi
  • Connectivity: mkHDMI, mkUSB/OTG, mkSDXC
  • Battery: 8500mAh

MSRP: 1299CNY (approximately $210US).

First impressions
Fast, responsive, light, crisp and bright
Several Chinese apps. Some of them installing other Chinese apps. (removed/disabled, except for tUI and TeclastAutoUpdater)
No Apps drawer. no widgets - Apple-like UI. (Apex Launcher installed)
Overall feeling of money well spent :D

Current problems
I've found two things that I don't like about the tablet:
First, the speakers. I can't complain about sound - there's some bass, highs are clear, overall quality is good. But it eludes me why would someone place two speakers on the same side?
Second, and hopefully, temporary one, is the battery meter. From 0% it goes to 100% in about 20 minutes (BTW, the tablet pulls 2A out of the bundled PSU), says "charging 100%", for few hours more the current is still 2A, then 1.5A for some time, then 1A (somewhere here its starts to say "Charged"), and after 8 hours, when the current was 0.2A, I've disconnected the cord. "Bleep! Connect the charger! 10%" :eek: After an hour of use, I turned it of, then on... 77%! Went down to 8% after an hour more, then to 7% in another hour... :silly: A firmware update is definitely needed here. BTW, in 2 days I own the thing, I've had 2 updates, so the manufacturer's developers are doing something.
Click to expand...
Click to collapse

Thanks so much for the review. I have been looking at this tablet and decided to purchase. I ordered from Ali express I think from the same seller you did (qh store) when I get it I'll let you know if I have the same battery issues.
 
L

lala206

Member
Apr 6, 2011
11
0
sensors??

Hi, Im considering about this tablet but there is a small question that I wanna know before purchasing which is how many sensors this device has, does it has e compass and gyroscope as well as gravity sensors? Would you mind checking it for me?
Thanks in advance!
 
A

avich

Member
Oct 16, 2010
19
9
GTA
lala206 said:
Hi, Im considering about this tablet but there is a small question that I wanna know before purchasing which is how many sensors this device has, does it has e compass and gyroscope as well as gravity sensors? Would you mind checking it for me?
Thanks in advance!
Click to expand...
Click to collapse

I am attaching AnTuTu test results, the last one says there is no G-Sensor, or compass, only Acceleration and Light sensors. However my seller indicated that there is gravity sensor, so there is a possibility (I hope) that it will appear after some magical firmware update. ;)
 

Attachments

  • Screenshot_2014-05-08-19-03-31.png
    Screenshot_2014-05-08-19-03-31.png
    153.5 KB · Views: 3,540
  • Screenshot_2014-05-08-19-03-56.png
    Screenshot_2014-05-08-19-03-56.png
    190.8 KB · Views: 2,454
  • Screenshot_2014-05-08-19-04-21.png
    Screenshot_2014-05-08-19-04-21.png
    167.8 KB · Views: 2,366
  • Screenshot_2014-05-08-19-04-43.png
    Screenshot_2014-05-08-19-04-43.png
    202.1 KB · Views: 1,670
  • Like
Reactions: jclu52
BobBro

BobBro

Senior Member
Nov 23, 2011
157
60
tPad :)

They call it a tPad as a takeoff of the iPad :) I have had mine now for almost 3 weeks with very little trouble. I have not noticed the battery thing but I will keep an eye out for it. Yeah a bit strange about the speakers but what are you going to do. I have had 2 updates so far also. You can get Windows 8.1 on it now but it is a bit of a pain from what I can see to install from the factory website and doing a Google translate. Here is the link for the x98 forum. http://bbs.teclast.com/forum.php?mod=forumdisplay&fid=48 I think there is a new way to install Windows coming on the 15th. For the money ( I paid 1149 RMB-about $185 USD on Taobao when it first came out) I think you can't beat it. Great speed, great screen, 3G and I think it will be able to dual boot soon. Hope they get 4.4 on it soon :cool:
 
  • Like
Reactions: jclu52
D

Davidencio

New member
May 14, 2014
4
0
Hdmi

I'm looking for a tablet and this gives me good vibes HDMI its important for mi could somebody guarantee me that if this tablet has this port?
And another question, when W8.1 comes up officially, does it has a dual boot or we can only use an OS?
 
L

lessismore8848

New member
Sep 29, 2012
2
1
Nice review!

jhnchristopher said:
Thanks so much for the review. I have been looking at this tablet and decided to purchase. I ordered from Ali express I think from the same seller you did (qh store) when I get it I'll let you know if I have the same battery issues.
Click to expand...
Click to collapse

Thanks for a lovely review :good: I too found this tablet absolutely fast and smooth but with few glitches as you mentioned like akward speaker positioning and battery drainage. Battery issues will be fixed soon hopefully. I used VRoot chinese version to root. Waiting for windows 8.1 update!
 
  • Like
Reactions: jclu52
S

Sparh4wk

Senior Member
Nov 26, 2012
133
9
anyone who have this tablet can tell me about glass? is there some kind of protection like gorilla glass etc, or is easily to scretch it like Onda V975m? Im choosing my tablet now, but dont wanna waste my money..
 
L

lala206

Member
Apr 6, 2011
11
0
thank you

avich said:
I am attaching AnTuTu test results, the last one says there is no G-Sensor, or compass, only Acceleration and Light sensors. However my seller indicated that there is gravity sensor, so there is a possibility (I hope) that it will appear after some magical firmware update. ;)
Click to expand...
Click to collapse

Thank you very much! Finally, it lacks so many sensors. Im a bit disappointed, but actually maybe I still go for it because of Windown 8.1 full
 
J

jhnchristopher

New member
May 11, 2014
2
0
do google apps work?

Can anyone confirm If Google apps work? Google maps {turn by turn directions}, contact sync and other apps? Thanks in advance.
 
E

eteles

Senior Member
Aug 20, 2012
668
151
Hi guys!! I'm thinking of replacing my V975M for this the teclast X98... What do you guys think? What is Antutu X score for this one? Not Antutu... Where to buy it? Thanks!
 
rasoooli

rasoooli

Senior Member
Jul 22, 2010
260
57
eteles said:
Hi guys!! I'm thinking of replacing my V975M for this the teclast X98... What do you guys think? What is Antutu X score for this one? Not Antutu... Where to buy it? Thanks!
Click to expand...
Click to collapse

If you dont need GPS & 3G

Best Choice is Onda V975I
Becuse Onda is The best company in firmware support

For example Huawei Never released any new Firmware For MediaPad 10 FHD ( good hardware )
But
Onda every month release New version of android for their product

.
 
Last edited:
E

eteles

Senior Member
Aug 20, 2012
668
151
rasoooli said:
If you dont need GPS & 3G

Best Choice is Onda V975I
Becuse Onda is The best company in firmware support

For example Huawei Never released any new Firmware For MediaPad 10 FHD ( good hardware )
But
Onda every month release New version of android for their product .
Click to expand...
Click to collapse

Dude, I have the Onda V975M and let me tell you something about Onda... Their firmware SUCK... It's so much bugged that they have to release several updates... But the worse thing is that the bugs keep coming back every other update and you feel that nothing has really improved...

Another thing is that they are liers... They cheat at Antutu... They claim the CPU runs at 2.0Ghz (for the V975M) but the frequency is NEVER used by the system, except for cheating at Antutu benchmark...

They don't release source code, so you can't unlock the frequencies on kernel or have code modification for building better custom roms, or for the community to fix their mess...

The only reason they release so many updates is that they launch the product so early that their first ROMs leave the tab quite unusable, with system lag, rebooting, WiFi and sd card disconnection when tab sleeps... having to reboot tab to reconnect WiFi every time it sleeps and much more terrible bugs...

Not to mention the update procedure, that has 50% chance of hard bricking your tab... another thing: it doesn't have download mode and Sd card booting doesn't work after bricking...
 
Last edited:
  • Like
Reactions: ozerec88 and brownsmell
M

mohamad_skiller

Senior Member
Nov 30, 2013
63
17
QQQ

hi i want to buy this tablet but i have several question can any one help me if he have this tablet or know this question ?
1- can you tell me How long does it take the battery use on wifi and 3g connect with 50%brightness ?
2-can you tell me How long does it take the battery use on 3d gaming ?
3-can you tell m eHow long does it take the battery use on play back fhd movies ?

***How long does it take to fully charge the batteries?

4-whats your observation about battery life in this tablet ?

5-can i make a gsm phone call with tablet(2g) ?

6-can you tell me problems do you have with tablet (cons)?

7-do you recommend i will buying this tablet ?

thank you very much if you will answer my question
 
H

harpdoc

Senior Member
Aug 1, 2008
171
18
I found a review that said that this processor is not compatible with many 3d games, and wouldn't load 4 of 10 3d games that they tried. Can any of you that own this tablet confirm or refute this?
 
X

xclub_101

Senior Member
Oct 15, 2012
1,252
358
Samsung Galaxy S23 Ultra
harpdoc said:
I found a review that said that this processor is not compatible with many 3d games, and wouldn't load 4 of 10 3d games that they tried. Can any of you that own this tablet confirm or refute this?
Click to expand...
Click to collapse

That is very likely true for the moment - many games come with binary optimized code for ARMv7 32-bit architecture, while this one is Intel x64 and just started to appear on low-cost devices. But I would expect things to get (much) better in a few months. I also think there might be a possibility that gaming could be a lot better with some games under the (extra-cost) Windows OS.
 
You must log in or register to reply here.

Similar threads

Hendrickson
Onda v919 Air 3G Dual Boot 9.7" 2048x1536 px - Z3736F - 3G - Android/Windows
Replies
645
Views
239K
A
adepoyu
uncleabubear
  • Poll
CHUWI Hi9 Air 64GB MT6797 X20 Deca Core 10.1 Inch 2K Screen Android 8 Dual 4G Tablet
Replies
2K
Views
328K
G
Gumka1977
CoopZor
Finally Ipad smoothness : Onda V975M Quad Core 2.0GHz 9.7 Inch Retina Screen
Replies
687
Views
243K
G
grole
oeriel
Teclast X70R - C7F9 - Tablet - Android 5.1.1 - Intel SoFIA Atom X3-C3230
Replies
172
Views
110K
A
adexmont
T
Android TV x86
Replies
1K
Views
537K
Peter12205
Peter12205

Top Liked Posts

24 Hours All time
  • There are no posts matching your filters.
  • 12
    Logseman
    Logseman
    KitKat update guide (HKC1 ONLY)

    So let me do the tutorial real quick. This is a translation from this tutorial: http://hispatablets.com/teclast-x98/tutorial-para-instalar-kitkat-teclast-x98-hkc1-t1790.html

    Requirements:

    Steps:
    1. Installl Drivers
    First of all, let's install the necessary files. Install in the following order:
    1. iSocUSB-Driver-Setup
    2. IntelAndroidDrvSetup
    3. ManufacturingFlashToolSetup
    Once those three are installed, copy the CUSTOM_CONFIG.INI file in the folder where you've installed Manufacturing Flash Tool. The default path is C:/Program Files[(X86) if you have a 64-bit machine]/Intel/Manufacturing Flash Tool.

    Unzip the big firmware file (KK-HKC1.zip) and check for a file called flash.xml.

    2. Extracting VID/PID
    We open Manufacturing Flash Tool, we click on File-Settings, and the following appears:

    Manuf1_zpsf4bd57b4.png


    We have to input the VID and PID values for our device so MFT recognizes it. We'll have to put it in Flash mode and Droidboot mode so we get the 2 VID and 2 PID values necessary. We get the reading of the VID and PID values from the Device Manager in the following fashion:

    2.1 Extract VID and PID from Flash Mode (SOC Devices)
    1. Turn device off
    2. Hold both volume buttons AND the power button until the Teclast logo appears
    3. Connect the tablet with the MicroUSB cable
    4. Once connected, go to Control Panel-Device Manager
    5. Seek the Intel Android Phone category, just over Intel SOC. Expand it and right-click on Android ADB-Interface. Click on Properties
    6. In the Properties Menu, click on the Details tab (third one) and then on the scrollable list. Check Hardware ID.
    7. You'll see two alphanumeric codes, one for VID and the other for PID. Take note of them,
    8. Unplug the USB cable and leave the tablet alone for a bit. It'll turn off on its own.

    2.2 Extract VID and PID from Droidboot (Android Devices)
    1. Turn device off
    2. Hold both the Volume+ AND the power button until the Teclast logo appears, and then the Droidboot screen (similar to Fastboot)
    3. Connect the tablet with the MicroUSB cable
    4. Once connected, go to Control Panel-Device Manager
    5. Seek the Intel Android Phone category, just over Intel SOC. Expand it and right-click on Android ADB-Interface. Click on Properties
    6. In the Properties Menu, click on the Details tab (third one) and then on the scrollable list. Check Hardware ID.
    7. You'll see two alphanumeric codes, one for VID and the other for PID. Take note of them,
    8. Unplug the USB cable.
    9. Browse with the volume buttons until you get to the Power Off option. Confirm with the Power button and the tablet will turn off

    Once we have the VID and PID values, we input them on the Manufacturing Flash Tool in this specific way:

    Manuf2_zpsc2770f2b.png


    In my case, the values were:
    Soc Devices: VID 8087, PID 0A65
    Android Devices: VID 8087, PID 09EF

    3. Installing the firmware

    Now we have MFT open, so we close the Settings menu with "OK" so the VID/PID values are confirmed. Now the good part comes: installing the firmware. We click on File-Open and we browse for the folder with the unzipped firmware. Look for the flash.xml file and select it,

    It's time to put the device on flash mode. With the device turned off, we hold both volume buttons and the power button until the Teclast logo appears. Connect the tablet right after that and let it be. As you see from my log, the flashing takes at least 8 minutes, so be patient and FOR THE LOVE OF ALL WHAT'S HOLY DON'T DISCONNECT THE TABLET WHILE IT'S FLASHING. It'll do everything on its own, including the reboot.

    4. Fixing the audio

    If we stop there, we'll notice quickly that there's no sound input (mic won't work) or output (no sounds come from the speakers). We need to inject a couple of files.

    1. Download Audio_Update.zip and unzip it
    2. Turn on the tablet and activate ADB debugging mode in the settings
    3. Open the folder where you've unzipped it and open a shell (command window)
    4. Plug the tablet to your computer
    5. Run the following commands:
      Code: 
      [B]adb devices[/B]
[this is so we check that the tablet is correctly seen by the computer, it should say "BayTrail something"]
[B]fpt-setup.bat[/B]
[ignore the error that comes out]
[B]update.bat[/B]

    Once you've ran the three you'll be prompted to press a key. The tablet will be rebooted and you'll get to say "OK Google" in peace.
    __________________________________________________________________________________________

    And that's it. Enjoy the chucklet!

    Thanks have to be given to leroys who provided the firmware. Also dukito from HispaTablets provided the driver files that I link in the Mega folder. I hope you enjoy it, Remember that no success is guaranteed and that any result is your and only your responsibility. Which is fine.
    View
    6
    mihaiolimpiu
    mihaiolimpiu
    TECLAST X98 3G, Allview Viva/Impera i10G Windows - Final version! Fully tested!

    TECLAST X98 3G, Allview Viva/Impera i10G
    ATTENTION READ CAREFULLY:
    THIS IS NOT THE SAME TABLET as Teclast x98 AIR 3G, don't use any BIOS'es or roms from the AIR, AIR II. It has a different processor! Flashing a wrong bios will brick your tablet!
    x983g_zt_01.jpg

    Manufacturer's page:
    http://www.teclast.com/en/zt/x983g/

    Technical characteristics:
    • Screen size: 9.7 inches
    • Screen type: IPS (Retina Display)
    • Screen resolution: 2048 * 1536 (4:3)
    • Processor: Intel Bay Trail 64 Z3735D 1.83 Ghz
    • Memory: 2 GB DDR3L
    • Internal memory: 32 GB EMMC
    • Operating system: Android 4.2
    • Camera: 2mp front, backside 5mp
    • Support for WCDMA, Wi-Fi (IEEE 802.11 b/g/n)
    • GPS navigation + A-GPS
    • Bluetooth, WIDI
    • SIM card slot
    • Micro USB port
    • 3.5 mm headphone jack
    • memory card support TF CARD 64 GB (tested with SanDisk card)
    • OTG
    • Built-in dual speakers and microphone
    • Battery: 8500mAh
    • Size: 239.5 mm (d) x 180.5 mm (w) x 8.6 mm (H)
    • Weight: 602g
    Google Drive with all necessary files for Android/Windows conversion! These are not the latest version but will do the job!

    Configure your system for correct installation:
    Install Intel drivers (From Teclast › Drivers_Tools)
    Please install the drivers on your PC in the following order:
    iSocUSB-Driver-Setup-1.0.4.exe
    IntelAndroidDrvSetup1.5.0.exe
    (In the case you are still using Windows XP Please install NetFramework_3.5_full.exe).

    How configure software installation:
    Install Intel Manufacturing Flash Tool.
    I could be necessary to copy a custom CUSTOM_CONFIG.INI file to the program installation folder, please see your manufacturer instructions for updating your tablet. I'm not going to be very specific as I have a Allview Viva I10G, and it could be different....
    Go to C:\Program Files\Intel\Manufacturing Flash Tool.
    Start Manufacturing Flash Tool.exe
    Go to: “File”->“Settings”->“General properties”->“SOC devices”->“VID”-> insert 8087 and into “PID” -> insert 0A65 -> “OK”
    Software update: “File”->”Open” select flash.xml file from update folder.
    Switch the tablet OFF and while holding the "VOL +" and "VOL-" click "Power". When the tablet stops at the manufacturer logo, connect the tablet to the PC.
    DO NOT DISCONNECT THE TABLET WHILE FLASHING!

    If it's not working reinstall Android Drivers or check Hardware manager the Android Device that appears in "Flash Mode" has the same VID-PID as instructed above. If they are different, try to use the ones that are used. This is not quite clear, needs more work!

    SIMPLEST WAY TO INSTALL WINDOWS from Android/ROOT ANDROID/FLASH BIOS/CONFIGURE WINDOWS USB!
    Go to Google Drive with all necessary files for Android/Windows conversion! and download Toolbox.rar. Unrar it to your folder of choice and run it by starting as Administrator 1_Toolbox.bat!
    This utility shows you how to enable developer mode, and also checks if the drivers are installed... If not it will install them for you!

    Now run in this order, following all instructions:
    ToolBOX Teclast x98_3G

    a) Download files, which needs for install WINDOWS.
    This option downloads a Windows 8.1 ISO for our tablets and places the files in the ToolBox folder.

    b) Prepare Windows boot USB-Drive.
    Pretty self explanatory, you need a 4GB+ FAT 32 USB disk. It will format the disk and inject the previously downloaded files in the USB drive.

    c) Install "update.zip".
    Maybe if you have a factory TECLAST ROM you should do it? I don't know what it does?
    I never installed it, but I tested on a ALLVIEW VIVA I10G and the process is somewhat different! I've installed the Android files using intel MFT. :(

    d) Flash a firmware to Tablet-PC. (FastBOOT)
    It should install latest Teclast Android ROM 116, THAT IS NEEDED TO HAVE A FULLY FUNCTIONAL TOUCH in Windows. If you skip this step Windows will work OK, but you won't have a functional touchscreen whatever you do!
    If You are already on Teclast 116, you can skip this step!

    If it doesn't flash properly the first time you try (like me on a ALLVIEW VIVA I10G) skip this step, install Allview Android rom back into the tablet, install windows without touch support by skipping step c and d, then convert back by flashing a TECLAST ANDROID BIOS and a proper TECLAST android 116 rom, then repeat the process from a to f!
    To flash Android/Windows Bios at will use fptw_NEW.zip.

    e) Install ROOT and BUSYBOX (Android).
    Gain root, required for flashing BIOS!

    f) Flash BIOS to Tablet-PC.
    This will flash original teclast windows bios to the tablet.
    ATTENTION: AFTER SUCCESSFUL BIOS FLASH, HOLD POWER FOR AT LEAST 10 SECONDS TO SHUTDOWN THE TABLET! This will minimize the chances of getting a brick!

    Install Windows 8.1 on Tablet

    1. connect the USB hub to the Tablet, it connect the keyboard and the bootable USB flash drive you created earlier using TOOLBOX.
    2. turn on your Tablet and press Delete several times.
    3. In the window that appears, go to category select BIOS Save & Exit
    4737773.jpg


    4. In the category Boot Override, select to Boot USB flash drive
    Then Save and exit!

    5. install Windows 8.1 if everything was done correctly, will start automatically.
    4737774.jpg

    6. After the advent of "Operation Successful", immediately unplug the USB flash drive.
    4737775.jpg

    7. turn off the Tablet by long pressing Power.
    8. turn on the tablet.


    Congrats! You have successfully installed Windows 8.1!

    After successful installation install every driver from drova.zip manually. Right click on every .inf and select install.
    EDIT: After windows 10 November update:
    Complete ALLVIEW Impera i10G (Teclast x98 3G) Official windows 10 driver package that fixes touch problems can be obtained here!




    After windows install, now what? Quick fixes, driver updates, longer lasting battery...
    1. First step will be to upgrade to windows 10, it's newer, works really well, and you will get some updated drivers out of it! Don't forget to insert your license number prior to upgrading so you can take advantage of the free upgrade from Microsoft ;)

    2. Install Wi-Fi Fix. Teclast WIFI Optimization tool, I have it installed but I don't really know if it makes a difference. It's for x98 Air 3G. After I've installed it and ONDA 911 my WiFI is 100% stable. It could be the BIOS or this program, I don't know, but it works.

    3. Update your bios:
    Teclast BIOS11.09.2014 is recommended or latest 911 version (found it at last, all bios-es HERE). Teclast BIOS 28.08.2014 has a touchscreen bug that crashes the touch drivers with 5+ touch points! Onda 911 works sometimes better but you need to sacrifice 3G and GPS, everything else is stable including touch and wireless.

    4. BATTERY DRAIN FIX UNDER WINDOWS (thanks to vpx)
    The main problem is very old (year 2006) driver of "Intel SD Host Controller", they are 3 in Device manager. Only thing what you need is update driver.
    • start Computer Management (hold My Computer and select Manage)
    • select Device management
    • find SD Controllers, if you click on it, there are 3 "Intel SD Host Controller"s
    • hold on every one controller, select "Update Driver", select driver from computer, and there is another option "SDA Standard Compliant SD Host Controller", install driver, confirm restart of computer after last update install.
    • reboot

    5. UPDATED WIRELESS AND BLUETOOTH DRIVERS (thanks to Hendrickson)
    If you have problems with wireless when using Bluetooth at the same time it was so damn slow, you can use updated Bluetooth and Wireless drivers attached to this post ( Air_3G_Updated_WLAN_and_BT_drivers.zip).
    These drivers were discovered November 4th from Dell site and seems to have fixed the issue.

    6. FIX Bluetooth only works only in settings page. Disable "Allow the computer to put this device to sleep" in power management page. (24.05.2016, new drivers don't need this fix)

    7. Install Comneon Modem driver. Use compatibility mode to install the driver, it's not visible in the METRO interface, but you can use the modem as a dial up modem. I never use it, I know it works. tough...

    8. Lower Video card preallocated ram. The tablet has 2 Gb of ram and by default 512 Mb are already allocated to the video card. I use 128/256 for the preallocated video RAM, as the card can still go up to 512 if needed. This setting lets Windows use up to 1.9 Gb ram wich is more than enough for a fluid experience. You can change this is the bios, look for preallocated vram (or something like that).

    9. DON'T CHANGE ANYTHING ELSE IN THE BIOS. The settings range from nonworking to doing something totally different. It's better to leave them alone there is nothing too interesting there and messing with the USB settings could make the USB port fail (remember it's the only port, your only recovery if something fails).

    10. Disable fast boot and related settings in bios, this removes the Teclast logo on boot to an American Megatrends one (BIOS POST SCREEN) wich is more pleasant to the eye than those Chinese characters! Speedwise, I haven't noticed any difference!

    11. Update Kionix Rotation Sensor and Sensor Fusion - 2015 1.28.3. Try to backup your Orientation registry setting first.

    12. Delete recovery partition: Only if you installed Windows 10, you can safely delete Windows 8 recovery partition. It's best to use the Disk Manager tool included in windows as it allows you to delete recovery partition and also resize the system partition. You win ~500 mb ? on the system drive by deleting the unused recovery partition. You can't go back to windows 8 if you do this. You can also delete windows 8 backup files (it gets deleted automatically after 30 days?)! Windows 10 recreates this partition at every major update so it's not a good tip!

    13. Clean windows WinSxS folder after using WINDOWS UPDATE (thanks to jcespi2005)
    Follow these instructions to clean WinSxS folder.

    14. Fix touchscreen is sluggish, high system interrupts bug.
    BUG IS CAUSED BY A WINDOWS SETTING, Windows 10 Fast Startup. To disable it follow this tutorial! or just run the attached bat file as administrator!
    This was tested with the IMPERA drivers!
    The driver is not perfectly compatible with our tablets, and sometimes portions of the screen just don't work. To also fixor at least minimize the issue turn off power saving for I2C HID device.
    attachment.php



    Known Problems/bugs

    • Front camera is very good for skype and communication programs, only the photos have a violet hue. I found out that this is a problem with some camera modules only!
    • Back Camera is too dark and autofocus doesn't work With the latest drivers and windows 10 1511 camera is fixed!
    • 3G modem can be used only as a ON DEMAND connection as the drivers are for windows 7. Metro interface doesn't recognize the modem at all.
      I think this is caused by an incomplete flash procedure, Checked my bios against an Impera Bios and on mine, intel TXE version was missing, but on Impera was version 00.05.00.00 and 01.00.02.1060. You just need to use a flash with complete information, that info can be extracted from first Allview Viva i10G update.
    • Touch is problematic. ?! With the latest drivers and Disabling Windows fast startup touch is fixed 99%!

    This "Tutorial" was compiled in my free time, take it as it is, it worked for me, I've inspired from 4PDA thread and want to thank those guys for their great help, from techtablets and from the x98 Air thread here on XDA (that is pretty similar hardware).

    Converting back to android (simple version, don't have time to make a complete tutorial):
    Just flash the latest Teclast Android Bios and install latest Teclast Rom. Easy as pie!
    NEVER INSTAL ALLVIEW VIVA BIOS if you're converting to Android, it bricks the tablet 100% of the time! On my tablet when converting from Android, I was forced to use only Teclast 116 ROM, as Allview Viva's Rom has the touch Inversed!
    Teclast's 116 Rom Works great it has a problem with not working sound after Android Conversion! To fix this, Download the First Allview Viva Rom update, and somewhere in the upgrade files there is a 4.2.bin file... It's a bios file, just flash it and everything will work great!


    24.06.2016: Hi guys, this is my last update to this thread, I upgraded to an Teclast X98 Plus 3G.
    Try to read the original 4PDA post first, but using the toolbox is pretty easy!
    View
    5
    C
    crazedone
    Rooting 4.4.2 KitKat

    SuperSU doesn't work too well, or the way I did it didn't work (i.e. You could get root prompts, but SuperSU app would be in an endless wait when you opened it to manage your apps, which was bad). So I decided to try Clockworkmod (Koush's) Superuser app, and it works nicely. I blundered my way through it, but the following should be a nice distilled version.

    Prerequisites:
    • A computer with the necessary drivers
    • Developer mode enabled and ADB enabled

    1) Download APK of Koush's (Clockworkmod) Superuser (Zip file)
    2) Locate x86 su binary and extract
    3) Enable ADB over USB in developer's options
    4) Install CWM Superuser from playstore but don't open it just yet

    5) Here we will prepare a partially rooted system
    Code: 
    # Remount /system as RW
adb root
adb remount
adb shell
mount -o rw,remount /system
exit
    Code: 
    # Get the su binary across
adb push su /system/xbin/
adb shell
chmod 6755 /system/xbin/su
ln -s /system/xbin/su /system/bin/su
exit

    Code: 
    adb reboot

    Code: 
    # Temporary root
adb root
adb remount
adb shell
mount -o rw,remount /system
su --daemon

    6) We have a temporary rooted system, install Stericson Busybox from playstore
    7) Install busybox without smart install, you should get a superuser prompt

    8) We will imitate a (SuperSU) rooted system by using ES file manager to make the following files:
    [/system/etc/.installed_su_daemon]
    Code: 
    1

    [/system/etc/install-recovery.sh]
    Code: 
    #!/system/bin/sh
/system/xbin/su --daemon &
/system/etc/install-recovery-2.sh

    <ADB Root Shell>
    Code: 
    chmod 666 /system/etc/.installed_su_daemon
chmod 755 /system/etc/install-recovery.sh

    Get term-init.sh from: http://xdaforums.com/showpost.php?p=32716412&postcount=2
    Thanks to Ryuinferno!

    9) Enable init.d support, upload term-init.sh to sdcard
    Code: 
    adb push term-init.sh /sdcard/
    or download from the link and then from adb
    <ADB Root Shell>
    Code: 
    sh /sdcard/term-init.sh

    10) To make su load its daemon every boot, we will need some init.d scripts
    [/system/etc/init.d/99SuperuserDaemon]
    Code: 
    #!/system/bin/sh
/system/xbin/su --daemon &

    11) That should be it! Reboot and make sure init.d works in /data/Test.log
    <ADB Root Shell>
    Code: 
    exit
adb reboot
    View
    3
    A
    avich
    I could not find this tablet mentioned anywhere on XDA, so I've decided to create this thread for sharing impressions and useful information between owners and anyone interested.

    x983g_zt_01.jpg


    Manufacturer's page:
    http://www.teclast.com/en/zt/x983g/


    Specifications:
    • CPU: Intel Bay Trail-T 3735D 64bit, 22nm, 1.3(turbo 1.83)GHz
    • RAM: 2GB (DDR3L)
    • ROM: 32GB eMMC Flash
    • Display: 9.7 inch IPS 2048x1536
    • Camera: 2MP front / 5MP back (AF)
    • Radio: 802.11b/g/n, GSM+WCDMA, GPS, BT 4.0, WiDi
    • Connectivity: mkHDMI, mkUSB/OTG, mkSDXC
    • Battery: 8500mAh

    MSRP: 1299CNY (approximately $210US).

    First impressions
    Fast, responsive, light, crisp and bright
    Several Chinese apps. Some of them installing other Chinese apps. (removed/disabled, except for tUI and TeclastAutoUpdater)
    No Apps drawer. no widgets - Apple-like UI. (Apex Launcher installed)
    Overall feeling of money well spent :D

    Current problems
    I've found two things that I don't like about the tablet:
    First, the speakers. I can't complain about sound - there's some bass, highs are clear, overall quality is good. But it eludes me why would someone place two speakers on the same side?
    Second, and hopefully, temporary one, is the battery meter. From 0% it goes to 100% in about 20 minutes (BTW, the tablet pulls 2A out of the bundled PSU), says "charging 100%", for few hours more the current is still 2A, then 1.5A for some time, then 1A (somewhere here its starts to say "Charged"), and after 8 hours, when the current was 0.2A, I've disconnected the cord. "Bleep! Connect the charger! 10%" :eek: After an hour of use, I turned it of, then on... 77%! Went down to 8% after an hour more, then to 7% in another hour... :silly: A firmware update is definitely needed here. BTW, in 2 days I own the thing, I've had 2 updates, so the manufacturer's developers are doing something.

    --- Update 2014-08-01

    I've got the POWER!

    The bad news are - (1) technical support does not answer emails, at least in my experience.. Probably because of language difficulties, maybe they have some other reasons. (2) replacement batteries are hard to find - on ali express I found only one seller who claims his batteries are 12Ah. The good news is - I did not need all of that. Finally, I've decided to open the thing up and check all accessible connection points.

    Disassembly
    You'll need a sharp tool (there are special plastic tools, but I used regular small knife to start, and a plastic one from ikea to widen and crack on the initial opening). Back cover is snapped on over the screen base on small latches, and all you need to do is slit the groove that goes around the screen a little, then go on unlatching until it comes apart. The groove is just around the screen, between two plastic parts, not around the metal cover.
    All I needed to do was tracking the battery wire, lifting black tape, and re-plugging the wire in its place. Full battery power is now restored. Feeling are mixed -- :D or :( ?
    View
    2
    Flash-A-Holic
    Flash-A-Holic
    [Guide] Teclast X98 3G - Dual Boot Windows/Android X86 [Marshmallow/KitKat]

    INFO
    I'm not the original developer of these builds. These builds are based on Android-x86 Open Source Project. All the credits goes to the original developers! I just slightly modded them and added couple fixes. Also I'm not responsible for bricked devices etc.

    HOW TO INSTALL ANDROID X86?
    This is not the only way to install Android x86 but probably the easiet way.
    Requirements:
    How to install:
    1. Install Android x86 4.4-r3 EFI to FAT32 partition using Android-x86 Installer UEFI Version. (If you have 8Gb FAT32 partition then you can select 3.5Gb for "Data size")
    2. After installation copy and replace "kernel", "initrd", "ramdisk" and "system" from Android x86 build (MM, CM13 or KK (links below)) to just created "AndroidOS" folder (in FAT32 partition). Then delete system.sfs from "AndroidOS" folder.
    How to reboot to Android from Windows 10:
    1. Open Settings, and click on the Update & security icon.
    2. Click on Recovery on the left side, and click on Restart now under Advanced startup on the right side.
    3. Select "Use a device"
    4. Select "Android-OS"
    5. Now your tablet will reboot to Android (You do not need to press any button anymore!)
    You can also use a shortcut which leads you to the step 3. Select "Use a device" directly. You can download Advanced_Startup_shortcut.zip from HERE. TIP: You can also change the shortcut icon. Just download ico-file (for example THIS) and then:
    1. Unzip Advanced_Startup_shortcut.zip and place the shotcut to desktop
    2. Right click shotcut and click properties
    3. Select change icon
    4. Browse to the ico-file and select it
    5. Done

    MARSHMALLOW 6.0.1

    DOWNLOAD

    KNOWN ISSUES
    Not working:
    • 3G
    • bluetooth
    • both cameras
    • sd-card reader
    • battery indicator (shows always 100%)
    • deep sleep is not working
    Bugs:
    • Touch will not work sometimes, reboot will fix it
    • Google Play Services has an error notification but Google Play Store etc. are working
      • Just enable all permission from Settings/Apps/Google Play Services
      • If you want to get rid of that notification then disable Google Play Music notifications from Settings/Apps/Google Play Music

    SOURCE

    XDA:DevDB Information
    Android x86 6.0.1 Marshmallow, Teclast X98 3G

    Contributors
    MikeR1029
    ROM OS Version: 6.0.1 Marshmallow
    ROM Kernel: Linux 4.4.10

    Version Information
    Status: Testing

    CyanogenMod 13 [Marshmallow]

    DOWNLOAD

    KNOWN ISSUES
    Not working:
    • 3G
    • bluetooth
    • both cameras
    • sd-card reader
    • accelometer
    • battery indicator (shows always 100%)
    • deep sleep is not working
    Bugs:
    • Touch will not work sometimes, reboot will fix it
    • Messenger app thinks that memory is full (false alarm)
    Others:
    • No GAPPS

    SOURCE

    XDA:DevDB Information
    Android x86 CyanogenMod 13, Teclast X98 3G

    Contributors
    Jyer
    ROM OS Version: 6.0.1 Marshmallow
    ROM Kernel: Linux 4.4.8

    Version Information
    Status: Beta

    KitKat 4.4.4

    DOWNLOAD

    KNOWN ISSUES
    Not working:
    • 3G
    • bluetooth
    • both cameras
    • volume buttons
    • deep sleep is not working
    Bugs:
    • Touch will not work sometimes, reboot will fix it
    • Accelometer is upside down. (You can use Rotation Control untill it is fixed).

    SOURCE

    XDA:DevDB Information
    Android x86 KitKat 4.4.4, Teclast X98 3G

    Contributors
    Ganper316
    ROM OS Version: 4.4.4 KitKat
    ROM Kernel: Linux 4.0.8

    Version Information
    Status: Beta

    Created 2016-05-22
    Last Updated 2016-05-24
    View

New posts