[NookHD/HD+] CM10.2 updated 01/18

Search This thread

verygreen

Senior Member
Feb 13, 2011
1,305
2,637
TN
linuxhacker.ru
CM10.2 for emmc is now part of nightlies not anymore, grab it for Nook HD+ or Nook HD
Also below are binary builds for SDCARD install for Nook HD+ only.
The last unofficial builds for emmc install while cm-10.2.1 is being finlized:
Nook HD+: cm-10.2-20140118-UNOFFICIAL-ovation-emmc.zip
Nook HD : cm-10.2-20140117-UNOFFICIAL-hummingbird-emmc.zip

Install instructions for SDCARD are the same as for cm10.1 sdcard, except you'll need newer gapps and a cm10.2 binary drop.
Install instructions for internal storage are the same as for cm10.1 emmc, except you'll need newer gapps and a cm10.2 binary drop.

The initial port is courtesy of @Hashcode

Latest binary SDCARD drop: cm-10.2-20140118-UNOFFICIAL-ovation-sdcard.zip

There are probably tons of issues, as this have seen only very little testing so far.

Known problems:
- Kindle app forcecloses sometimes.
- Location access does not work (workaround turn wifi off, then on).

Changelog (for sdcard builds only):
2014/01/18 - cm-10.2-20140118-UNOFFICIAL-ovation-sdcard.zip
- Fixed 1080p video playback on Nook HD+
2014/01/17 - cm-10.2-20140117-UNOFFICIAL-ovation-sdcard.zip
- Caught up with cm11 fixes: headset mic fix, bt tethering for some people, reenabled Trim.
2013/10/31 - cm-10.2-20131031-UNOFFICIAL-ovation-sdcard.zip
- Enabled a bunch of usb lte and usb network cards
2013/09/23 - cm-10.2-20130923-UNOFFICIAL-ovation-sdcard.zip
- Updated wifi drivers to R5.SP5.01
2013/09/03 - cm-10.2-20130903-UNOFFICIAL-ovation-sdcard.zip
- decreased max heap size due to braindead kindle app.
2013/09/01 - cm-10.2-20130901-UNOFFICIAL-ovation-sdcard.zip
- fixed filedescriptor leak in sensors HAL, hopefully putting an end to soft reboots
2013/08/30 - cm-10.2-20130830-UNOFFICIAL-ovation-sdcard.zip
- Experimental layer sizing changes to improve general smoothness
2013/08/22 - cm-10.2-20130822-UNOFFICIAL-ovation-sdcard.zip
- Some reorganization of overlays.
- Proper setup of present hardware buttons
2013/08/15 - cm-10.2-20130815-UNOFFICIAL-ovation-sdcard.zip
- Disabled FSTRIM support in ext4 while investigations are pending
- Enabled recovery quirk for Sandisk ultra 16G cards
2013/08/13 - cm-10.2-20130813-UNOFFICIAL-ovation-sdcard.zip
- Fixed mounting of internal storage
- Fixed reboot to recovery
- USB quicksettings restored
- wifi sleep fix (from upstream)
- Dalvik vm settings adjustments
2013/08/02 - cm-10.2-20130802-UNOFFICIAL-ovation-sdcard.zip
- Initial release
 
Last edited:

Sherip

Senior Member
Jan 26, 2012
299
51
Known problems:
- TBD

In general this is running great for me! Very smooth and speedy, and no spontaneous reboots so far.

One exception is the current free version of Titanium Backup. I can't seem to restore with it (getting parse errors). Their change log indicates recent changes for 4.3, but I guess they need more.

Sent from my Nook HD+ running CM 10.2 from SD
 

dmullens

Senior Member
Dec 23, 2011
106
17
This may be a dumb question, but where do I get the 4.3 gapps?

Sent from my Nook HD+ using Tapatalk 2
 

SteveCoops

Senior Member
Jun 12, 2008
65
7
While we are sorting out mainline CM merge issues, I thought you guys might be interested in playing a bit with CM10.2.

Install instructions are the same as for cm10.1, except you'll need newer gapps and a binary drop from this post.

The port is courtesy of @Hashcode

Latest binary drop: cm-10.2-20130802-UNOFFICIAL-ovation-sdcard.zip

There are probably tons of issues, as this have seen only very little testing so far.

Also this does not include usbhost quicksettings change ATM.

Known problems:
- TBD

Changelog:
2013/08/02 - cm-10.2-20130802-UNOFFICIAL-ovation-sdcard.zip
- Initial release

I'll give this a go if you do an emmc version
 

Sherip

Senior Member
Jan 26, 2012
299
51
I got my first soft reboot. When it came back up I had a startup message:

"System UIDs are inconsistent

UIDs on the system ate inconsistent, you need to wipe your data partition or your device will be unstatble."

The only option was "I feel lucky."

Probably above problem was caused by my continuing to try to restore stuff with Titanium. Since restoring apps wouldn't work, I tried restoring only data for a couple of apps I had installed thru the Play Store or restored from Google. Titanium gave no error restoring data, but the apps in question didn't run as if they had the data.

Sent from my Nook HD+ running CM 10.2 from SD
 

king200

Senior Member
Feb 13, 2012
1,072
402
In general this is running great for me! Very smooth and speedy, and no spontaneous reboots so far.

One exception is the current free version of Titanium Backup. I can't seem to restore with it (getting parse errors). Their change log indicates recent changes for 4.3, but I guess they need more.

Sent from my Nook HD+ running CM 10.2 from SD

You can likely use Nandroid Manager https://play.google.com/store/search?q=nandroid manager instead of Titanium Backup.
 

dmullens

Senior Member
Dec 23, 2011
106
17
I'm unable to get pie controls to work and I've had a couple of screen flashes. Other than that its working great!

Sent from my BN NookHD+ using Tapatalk 2
 

johje

Senior Member
Aug 27, 2008
53
18
I was able to get the new ROM installed along with the Play Store, but it seems to be running a little less smoothly than 10.1 did, but my memories of the SD version could be a bit romanticized since I switched to the emmc version of 10.1 and that is running great.

An issue I ran into is both HBO Go and Max Go apps say they are not compatible with this version when I tried to download them from the Play Store, but I don't know if that is a Nook HD+ issue or CM 10.2 issue.
 

Sherip

Senior Member
Jan 26, 2012
299
51
You can likely use Nandroid Manager https://play.google.com/store/search?q=nandroid manager instead of Titanium Backup.

Installed and looked at it on 10.1 (on emmc). Also made a current backup of my 10.1 via its cwm. I would try restoring some apps+data on 10.2 with Nandroid Manager but my nandroid bu is 2gb. Space is limited on my SD card, and currently I can't even see internal storage when I boot 10.2 from the SD card.

Someone mentioned trouble with extended desktop pie controls, that works fine for me in 10.2.

Sent from my HD+ Running CM 10.1 from emmc

---------- Post added at 01:18 PM ---------- Previous post was at 01:15 PM ----------

I'm unable to get pie controls to work and I've had a couple of screen flashes. Other than that its working great!

Sent from my BN NookHD+ using Tapatalk 2

My screen flashed a bunch while Google was doing some app restores. After that it was fine.

Sent from my HD+ Running CM 10.1 from emmc
 

hondoslack

Senior Member
Apr 6, 2009
194
37
While we are sorting out mainline CM merge issues, I thought you guys might be interested in playing a bit with CM10.2.

Install instructions are the same as for cm10.1, except you'll need newer gapps and a binary drop from this post.

The port is courtesy of @Hashcode

Latest binary drop: cm-10.2-20130802-UNOFFICIAL-ovation-sdcard.zip

There are probably tons of issues, as this have seen only very little testing so far.

Also this does not include usbhost quicksettings change ATM.

Known problems:
- TBD

Changelog:
2013/08/02 - cm-10.2-20130802-UNOFFICIAL-ovation-sdcard.zip
- Initial release

HA! My bluetooth mouse pairs with this build! Since the kernel seems to be the same as with CM10.1, perhaps the mouse pairing problem on 10.1 lies within the inner workings of bluetooth in Android, not the kernel?
 

webdroidmt

Senior Member
Dec 20, 2011
1,674
1,156
NJ
I was able to get the new ROM installed along with the Play Store, but it seems to be running a little less smoothly than 10.1 did, but my memories of the SD version could be a bit romanticized since I switched to the emmc version of 10.1 and that is running great.

An issue I ran into is both HBO Go and Max Go apps say they are not compatible with this version when I tried to download them from the Play Store, but I don't know if that is a Nook HD+ issue or CM 10.2 issue.

It's not a Nook issue but a JB 4.3 issue for HBO GO. The devs for the HBO app said they are working to get 4.3 compatibility as soon as possible.

I'm running Unofficial CM 10.2 on my N7 and some other issues were superuser root issues, which for the most part have been fixed. Also, because Google has changed the way fstab works in 4.3, there have been storage (force closes) and OTG issues. Fortunately, the excellent dev fattire has solved that issue for the N7.

Getting back to HBO GO, I use it a lot on my HD+, so I'll wait until it's compatible before updating to CM 10.2 on it.

EDIT: Some of you may want to try these 4.3 gapps, it contains the bare minimum of what you need to get the rom running. For stuff like Gmail, Google Now etc., you can just d/l from Play Store as you need it. https://mega.co.nz/#!owYEAA7L!2--5sUkqBmqXQ8d97xg3NKKrG-r5Al09rNopujQm6Dc

Mike T
 
Last edited:
  • Like
Reactions: killersloth

Eric Karz

Senior Member
Oct 30, 2012
285
92
First Verygreen
thanks for sharing 10.2
In one other thread it says Sand Disk (not recommended)
I am using a 64 gig sand disk ultra microSDXD UHS-l sd card for almost a day .
I haven't found anything wrong with using it .
if you could please point out for things to look for?
or maybe this version is ok to use the scan disk sd card ?
 

leapinlar

Senior Member
Oct 18, 2006
8,873
3,878
Just making sure, this cannot be flashed like emmc?

Sent from my BN NookHD+ using Tapatalk 4
This version is for SD only! Do not try to flash over the top of your emmc CM10.1 install! It may mess it up bad. I have tried to help two users that did not read this thread carefully and messed things up.

Sent from my Galaxy Tab 2 using XDA Premium
 

Sherip

Senior Member
Jan 26, 2012
299
51
In general this is running great for me! Very smooth and speedy, and no spontaneous reboots so far.

One exception is the current free version of Titanium Backup. I can't seem to restore with it (getting parse errors). Their change log indicates recent changes for 4.3, but I guess they need more.

Sent from my Nook HD+ running CM 10.2 from SD

My current understanding is, there are issues with superuser in 4.3. There is a beta update for superuser available (but I think it would need flashing, not simply installing, to the SD card install of CM 10.2)

Sent from my HD+ Running CM 10.1 from emmc
 

Whyzor

Senior Member
Jul 7, 2011
714
352
It seems that CM 10.2 is running ok even though it's very new. And official CM 10.1 hasn't started building yet (CM 10.2 I assume is weeks/months away) Can we get an eMMC CM10.2 build to test/experiment with it? Thanks in advance.
 

Top Liked Posts