[REF] How to remove yellow triangle on any firmware with JIG

Search This thread

anonymous572

Senior Member
Jun 15, 2011
897
428
Mstislavl
326y43.jpg


100% works for all Gingerbread, ICS and JellyBean ROMs TouchWiz Stock/Custom and AOSP/AOKP.
Works with new ICS and JB (4.0.3, 4.0.4, 4.1.1 and 4.1.2) ROMs
Italian translate by Willy89

1) You need a JIG. You can buy it or create its own
24b9pxd.jpg

2) Download attached zip archive and extract it to some folder
3) Reboot you device in download mode - turn it off, than hold volume down + center button + power button. Wait for the warning message and press volume up
4) Plug it to you PC
5) Start Odin from extracted folder and choose '1.tar' file for PDA flash. You must get the same settings:
13596410.jpg

6) Press Start and wait for the completion of the flashing
7) After reboot you should get black and dead screen. Unplug USB from PC. Long press power button (15-20 seconds). Remove battery for 5 seconds, plug in JIG, put battery back. Wait for 40 seconds, press power button for 5 seconds, remove JIG, long press power button (15-20 seconds), remove battery
8) Put battery back, hold volume down + center button + power button for 10-15 seconds, press volume up, plug it to you PC
9)
If you have GingerBread ROM TW stock/custom (Android 2.3.X) or any ICS and JB AOSP/AOKP (MIUI, Cyanogen, Paranoid and others) your step is:
Start Odin from extracted folder and choose '2.tar' file for PDA flash
If you have TW stock/custom ICS/JB ROM (Android 4.0.3, 4.0.4, 4.1.1, 4.1.2) your step is:
Start Odin from extracted folder and choose '2-ZSLPF.tar' file for BOOTLOADER flash
10) Press Start and wait for the completion of the flashing

At points 7-10 the screen will not work!

After these steps you will get:
- No yellow triangle
- Custom binary download value will set to 'NO'
- Current binary value will set to 'SAMSUNG OFFICIAL'


FAQ

Will it work for new stock gingerbread, ics, custom, cyanogen, miui and other firmware?
All gingerbread ROMs and ICS except CLP5 and CLP6 (some users report about incompatibility). Better don't use this reset counter instruction if you have those ICS ROMs.

Do I need root for this?
No.

Does not work, yellow triangle is not disappeared!
Carefully follow all 10 points of instruction.

I am having trouble, black screen after a 10th point!
Try reboot your device. Remove battery for 10 seconds and plug it back.

Odin can't recognize USB plug at 4 or 8 point. + Windows can't detect device or identifies as "Unknown device".
Try another USB port. Try reinstall kies or remove it and install only galaxy note drivers (link1, link2). If not helped try another PC.

Will this work on the Galaxy S2 or Galaxy Nexus?
No! You will break your phone. Works and tested for GT-N7000 and GT-I9220.

Will this work on the SGH-I717 (AT&T)?
Not tested yet.

Will I have a problem with a warranty? Can they identify the use of this counter reset?
There is absolutely no chance to detect this binary reset at service center.
 

Attachments

  • removeyellowtriangleNEW.zip
    2.2 MB · Views: 24,908
Last edited:

ck_looi

Senior Member
Dec 13, 2008
150
8
Why is it so troublesome? I thought it is exactly same as Galaxy S2...just plug in the usb jig when the phone is off, then it will boot to download mode, and reset the binary counter + remove triangle....
 
  • Like
Reactions: Cwelle

alesscam

Senior Member
Why is it so troublesome? I thought it is exactly same as Galaxy S2...just plug in the usb jig when the phone is off, then it will boot to download mode, and reset the binary counter + remove triangle....

Probabily you have a old bootloader in your gs2, because with new bootloader appened same problem like GNote

Inviato dal mio GT-N7000 usando Tapatalk
 

ludwiglaisne

Senior Member
Jul 1, 2008
62
7
On flashing 2.tar, Odin stop on "RQT_CLOSE !!"
What can I do ?

---------- Post added at 03:26 PM ---------- Previous post was at 03:21 PM ----------

I unplug usb, It indicate "FAIL" of course...
Then I tried to recovery (without jig), it works !!!
Everything's fine, but I spend some hard time for a moment !
 

RashaMatt

Senior Member
Jul 5, 2010
604
70
1. After doing this procedure, do we lose root and CWM? If so, How do we get them back? zergrush?

2. I have a jig that works with my SGS, but it doesn't "appear" to work with my Note. Is there any way to tell if it actually works before I start flashing foreign bootloaders? :D

TIA!
 
Last edited:

anonymous572

Senior Member
Jun 15, 2011
897
428
Mstislavl
1. After doing this procedure, do we lose root and CWM? If so, How do we get them back? zergrush?

2. I have a jig that works with my SGS, but it doesn't "appear" to work with my Note. Is there any way to tell if it actually works before I start flashing foreign bootloaders? :D

TIA!

1. No.
2. If it works with SGS it must works with Note.
 

RashaMatt

Senior Member
Jul 5, 2010
604
70
Very strange... I followed all instructions exactly, both flashes completed successfully (Odin says SUCCESS), and everything went according to plan...

EXCEPT... the yellow triangle is still there at the end!

:(
 
  • Like
Reactions: Tonyporsche

Top Liked Posts

  • There are no posts matching your filters.
  • 164
    326y43.jpg


    100% works for all Gingerbread, ICS and JellyBean ROMs TouchWiz Stock/Custom and AOSP/AOKP.
    Works with new ICS and JB (4.0.3, 4.0.4, 4.1.1 and 4.1.2) ROMs
    Italian translate by Willy89

    1) You need a JIG. You can buy it or create its own
    24b9pxd.jpg

    2) Download attached zip archive and extract it to some folder
    3) Reboot you device in download mode - turn it off, than hold volume down + center button + power button. Wait for the warning message and press volume up
    4) Plug it to you PC
    5) Start Odin from extracted folder and choose '1.tar' file for PDA flash. You must get the same settings:
    13596410.jpg

    6) Press Start and wait for the completion of the flashing
    7) After reboot you should get black and dead screen. Unplug USB from PC. Long press power button (15-20 seconds). Remove battery for 5 seconds, plug in JIG, put battery back. Wait for 40 seconds, press power button for 5 seconds, remove JIG, long press power button (15-20 seconds), remove battery
    8) Put battery back, hold volume down + center button + power button for 10-15 seconds, press volume up, plug it to you PC
    9)
    If you have GingerBread ROM TW stock/custom (Android 2.3.X) or any ICS and JB AOSP/AOKP (MIUI, Cyanogen, Paranoid and others) your step is:
    Start Odin from extracted folder and choose '2.tar' file for PDA flash
    If you have TW stock/custom ICS/JB ROM (Android 4.0.3, 4.0.4, 4.1.1, 4.1.2) your step is:
    Start Odin from extracted folder and choose '2-ZSLPF.tar' file for BOOTLOADER flash
    10) Press Start and wait for the completion of the flashing

    At points 7-10 the screen will not work!

    After these steps you will get:
    - No yellow triangle
    - Custom binary download value will set to 'NO'
    - Current binary value will set to 'SAMSUNG OFFICIAL'


    FAQ

    Will it work for new stock gingerbread, ics, custom, cyanogen, miui and other firmware?
    All gingerbread ROMs and ICS except CLP5 and CLP6 (some users report about incompatibility). Better don't use this reset counter instruction if you have those ICS ROMs.

    Do I need root for this?
    No.

    Does not work, yellow triangle is not disappeared!
    Carefully follow all 10 points of instruction.

    I am having trouble, black screen after a 10th point!
    Try reboot your device. Remove battery for 10 seconds and plug it back.

    Odin can't recognize USB plug at 4 or 8 point. + Windows can't detect device or identifies as "Unknown device".
    Try another USB port. Try reinstall kies or remove it and install only galaxy note drivers (link1, link2). If not helped try another PC.

    Will this work on the Galaxy S2 or Galaxy Nexus?
    No! You will break your phone. Works and tested for GT-N7000 and GT-I9220.

    Will this work on the SGH-I717 (AT&T)?
    Not tested yet.

    Will I have a problem with a warranty? Can they identify the use of this counter reset?
    There is absolutely no chance to detect this binary reset at service center.
    4
    Does it clear counter as well ?
    Yes, mine at zero with custom firmware.
    4
    hi,
    why in the zip there 2 files ?
    1.tar
    2.tar
    tks for reply mate
    Please read my instruction in first post carefully

    does that mean we can keep our gnote in warranty?
    Yes! :)
    2
    If I understand this correctly, tar 2 is the newer bootloader again.

    Yes this is correct. Your Galaxy Note bootloader returned after this procedure.

    jscurtu, there is absolutely no chance to detect this binary reset at service center!
    2
    1. After doing this procedure, do we lose root and CWM? If so, How do we get them back? zergrush?

    2. I have a jig that works with my SGS, but it doesn't "appear" to work with my Note. Is there any way to tell if it actually works before I start flashing foreign bootloaders? :D

    TIA!

    1. No.
    2. If it works with SGS it must works with Note.