Thank you good man
About a loud speaker - is there a possibility that loudspeaker will work on custom roms?
One X speaker/ charging dock?
- Thread starter WA_Bob
- Start date
-
- Tags
- accessories
Thank you good man
About a loud speaker - is there a possibility that loudspeaker will work on custom roms?
just received my speaker dock. I have a Internetional one x + but it doesen't work
fits perfectly with and without hard case but nothing happens no charging no sound .
Using Android Revolution HD 6.5 and tried viper but still nothing
do i need to instal another kernel or something to make it work ?
fits perfectly with and without hard case but nothing happens no charging no sound .
Using Android Revolution HD 6.5 and tried viper but still nothing
do i need to instal another kernel or something to make it work ?
I got mine yesterday, using ARHD 6.5 on HOX+ & it's working fine.
You may have to juggle it on to the poggo connectors.
Bad luck i think, going to go back to stock and try all again if that won't work i will check with friend with same phone if its the dock or my phone
yes i did, it worked so wassen't the charging dock,
Sended my phone back to the carrier, got it fixed now (didden't matter it was unlocked
One X + Int with Sense 5 update and S650 speaker cradle dock
So my kids are always breaking our phones - they love to yank loose the micro usb ports (sensation and my beloved G note1), or chew the top of the phone causing it to go into failed boot loaders - probably saliva related boot failure! (Htc desire S) or just plain break them (my old HD2 - still the greatest - and the missus old samsung!).
So nowadays the phones are screen and body protected and I thought I would get a pogo pin charging cradle for my recently bought HTC one x+ international - no child related cable yanking could occur, theoretically. Phone came in great condition from ebay and got a newish cradle dock from amazon. Except initially the cradle dock would not seem to recognise and charge the one x plus - no sound, no power, no charging icon - NADA - even though it seemed to be a perfect fit to the pins.
I wondered if I had made some error and it was not compatible with the x+ and only with the one X original. However, looking around the net there seems to be a few posts about the tendency of the pogo pins to GET DUSTY. I could see no overt dirt on the phone at all so I was sceptical.
So I tried using a small plastic wire/ cable tie and scrubbed out the pogo pin holes with the end til the connectors appeared to be SHINY again and then tried to rub them with a cotton bud/ Q tip. A very small amount of dirt came out of some holes BUT to my astonishment when I put my phone back on the dock - SOUND AND CHARGING WORKED PERFECTLY!!!
I have not tried to sync to pc yet but seems to be fine for charge and sound. I am amazed that the ports seem to be so prone to failure with such tiny amounts of dust. Does not bode well but at least its an easy fix. NEWS FLASH: Pogo pins are not the future! Crazy, crazy HTC!!!
Now all that i have to do is get the DOCK Mode working on sense 5. My phone is used but appears to be unrooted, stock HTC sense 5 as recent update. I reset the phone when I got it anyway. I hope this simple fix helps some one. Will update on sense 5 and the HTC dock mode/ apps when I try it out. peace.
QIK UPDATE:
HTC dock mode/ screen apps do not work with stock sense 5 in the versions uploaded in the earlier posts on this thread. Sense 5 or android JB force closes them. will look for more recent/ updated compatible versions of the apps.
So my kids are always breaking our phones - they love to yank loose the micro usb ports (sensation and my beloved G note1), or chew the top of the phone causing it to go into failed boot loaders - probably saliva related boot failure! (Htc desire S) or just plain break them (my old HD2 - still the greatest - and the missus old samsung!).
So nowadays the phones are screen and body protected and I thought I would get a pogo pin charging cradle for my recently bought HTC one x+ international - no child related cable yanking could occur, theoretically. Phone came in great condition from ebay and got a newish cradle dock from amazon. Except initially the cradle dock would not seem to recognise and charge the one x plus - no sound, no power, no charging icon - NADA - even though it seemed to be a perfect fit to the pins.
I wondered if I had made some error and it was not compatible with the x+ and only with the one X original. However, looking around the net there seems to be a few posts about the tendency of the pogo pins to GET DUSTY. I could see no overt dirt on the phone at all so I was sceptical.
So I tried using a small plastic wire/ cable tie and scrubbed out the pogo pin holes with the end til the connectors appeared to be SHINY again and then tried to rub them with a cotton bud/ Q tip. A very small amount of dirt came out of some holes BUT to my astonishment when I put my phone back on the dock - SOUND AND CHARGING WORKED PERFECTLY!!!
I have not tried to sync to pc yet but seems to be fine for charge and sound. I am amazed that the ports seem to be so prone to failure with such tiny amounts of dust. Does not bode well but at least its an easy fix. NEWS FLASH: Pogo pins are not the future! Crazy, crazy HTC!!!
Now all that i have to do is get the DOCK Mode working on sense 5. My phone is used but appears to be unrooted, stock HTC sense 5 as recent update. I reset the phone when I got it anyway. I hope this simple fix helps some one. Will update on sense 5 and the HTC dock mode/ apps when I try it out. peace.
QIK UPDATE:
HTC dock mode/ screen apps do not work with stock sense 5 in the versions uploaded in the earlier posts on this thread. Sense 5 or android JB force closes them. will look for more recent/ updated compatible versions of the apps.
Last edited:
USA version
----------------
So this worked on the the US version of the HOX+ on the European dock? I've been searching for a dock with pin charging for a while. Your method looks very simple. From what I gather, the pins only move over (down) the phone for the US version vs Euro version but are in the same orientation? Also a slight padding to go along the long edge in the dock to orient?
Correct???
Thanks
JOHN
After seeing someone mod the CR-S650 to fit the AT&T HOX, I ordered the dock and modified it to work with the HOX+. It was actually a lot easier than I thought because the POGO pins are only shifted over 1 space. So I took it apart, drilled a hole one space over and moved the entire POGO board over 1 slot. Now I have a working CR-S660 for my AT&T HOX+!
Moving the POGO pins over 1 slot lines up w/ the phone horizontally, but it's still a bit off vertically. I had to shave off the two small plastic tabs on the botton of the dock. This most likely means that I won't be able to use a case w/ the phone, but still very happy to have a working dock w/ POGO pins.
----------------
So this worked on the the US version of the HOX+ on the European dock? I've been searching for a dock with pin charging for a while. Your method looks very simple. From what I gather, the pins only move over (down) the phone for the US version vs Euro version but are in the same orientation? Also a slight padding to go along the long edge in the dock to orient?
Correct???
Thanks
JOHN
Truly Inspired!
Thank you so much for posting this!
Being a HOX+ (US) AT&T 4G LTE owner and devotee, I am truly inspired to attempt this mod.
Will I need to convert power from US to UK?
I will make sure to share pics if it turns out successfully.
KofaSing KoodGarma
http://www.pagone.com
After seeing someone mod the CR-S650 to fit the AT&T HOX, I ordered the dock and modified it to work with the HOX+. It was actually a lot easier than I thought because the POGO pins are only shifted over 1 space. So I took it apart, drilled a hole one space over and moved the entire POGO board over 1 slot. Now I have a working CR-S660 for my AT&T HOX+!
Moving the POGO pins over 1 slot lines up w/ the phone horizontally, but it's still a bit off vertically. I had to shave off the two small plastic tabs on the botton of the dock. This most likely means that I won't be able to use a case w/ the phone, but still very happy to have a working dock w/ POGO pins.
Thank you so much for posting this!
Being a HOX+ (US) AT&T 4G LTE owner and devotee, I am truly inspired to attempt this mod.
Will I need to convert power from US to UK?
I will make sure to share pics if it turns out successfully.
KofaSing KoodGarma
http://www.pagone.com
Last edited:
Similar threads
- Locked
Top Liked Posts
-
There are no posts matching your filters.
-
3
No need to flash custom ROM. For dock mode on stock ROM just install two applications: DockMode.apk and HTC_Dock_Screen.apk. That is all. Tested on HOX + international with ROM 1.17.401.1.3CR-S650 modification for AT&T HOX+
After seeing someone mod the CR-S650 to fit the AT&T HOX, I ordered the dock and modified it to work with the HOX+. It was actually a lot easier than I thought because the POGO pins are only shifted over 1 space. So I took it apart, drilled a hole one space over and moved the entire POGO board over 1 slot. Now I have a working CR-S660 for my AT&T HOX+!
Moving the POGO pins over 1 slot lines up w/ the phone horizontally, but it's still a bit off vertically. I had to shave off the two small plastic tabs on the botton of the dock. This most likely means that I won't be able to use a case w/ the phone, but still very happy to have a working dock w/ POGO pins.2No, but the one for the AT&T one X should work perfectly IIRC.
"Put AT&T's One X and One X+ side-by-side, and other than the color difference you'd be hard-pressed to tell them apart. The carrier's logo is slightly different, but that's about it -- even the docking pins in the back line up perfectly."
I'm not allowed to post links yet, if you want the source, just google the above quote in quotes.2One X + Int with Sense 5 update and S650 speaker cradle dock
So my kids are always breaking our phones - they love to yank loose the micro usb ports (sensation and my beloved G note1), or chew the top of the phone causing it to go into failed boot loaders - probably saliva related boot failure! (Htc desire S) or just plain break them (my old HD2 - still the greatest - and the missus old samsung!).
So nowadays the phones are screen and body protected and I thought I would get a pogo pin charging cradle for my recently bought HTC one x+ international - no child related cable yanking could occur, theoretically. Phone came in great condition from ebay and got a newish cradle dock from amazon. Except initially the cradle dock would not seem to recognise and charge the one x plus - no sound, no power, no charging icon - NADA - even though it seemed to be a perfect fit to the pins.
I wondered if I had made some error and it was not compatible with the x+ and only with the one X original. However, looking around the net there seems to be a few posts about the tendency of the pogo pins to GET DUSTY. I could see no overt dirt on the phone at all so I was sceptical.
So I tried using a small plastic wire/ cable tie and scrubbed out the pogo pin holes with the end til the connectors appeared to be SHINY again and then tried to rub them with a cotton bud/ Q tip. A very small amount of dirt came out of some holes BUT to my astonishment when I put my phone back on the dock - SOUND AND CHARGING WORKED PERFECTLY!!!
I have not tried to sync to pc yet but seems to be fine for charge and sound. I am amazed that the ports seem to be so prone to failure with such tiny amounts of dust. Does not bode well but at least its an easy fix. NEWS FLASH: Pogo pins are not the future! Crazy, crazy HTC!!!
Now all that i have to do is get the DOCK Mode working on sense 5. My phone is used but appears to be unrooted, stock HTC sense 5 as recent update. I reset the phone when I got it anyway. I hope this simple fix helps some one. Will update on sense 5 and the HTC dock mode/ apps when I try it out. peace.
QIK UPDATE:
HTC dock mode/ screen apps do not work with stock sense 5 in the versions uploaded in the earlier posts on this thread. Sense 5 or android JB force closes them. will look for more recent/ updated compatible versions of the apps.1
The adapter that comes w/ the dock works with US power in terms of voltage and amps, but you will need a converter/adapter to convert the plug so that it physically fits in a US outlet. You can get these at Radio Shack or other electronics store.
A STANDARD MicroUSB ADAPTER WILL NOT WORK because it will not get enough power. You need something that outputs 9V and 1.67A or the phone can't keep up w/ the charge. The perfect adapter to purchase would be the one for the HTC flyer. I can verify that it works perfectly w/ the dock and US power. Here's a link to one on ebay.
Yes, I have the US AT&T 4G LTE version of the HOX+ and purchased the European dock. Your assumption is also correct in that the PINS are only shifted over one space so you just have to drill a hole and physically move the board over one slot (and maybe shave off 1mm of plastic on the bottom of the dock for a perfect fit). It's really not that hard. In fact, the most difficult part is to take it apart and not accidentally disconnect any of the wires.
![fedele7n [ITA]](/data/avatars/s/12081/12081677.jpg?1648821546){kind=avatar}