[DFT][Updated!#3] HSPL / RSPL for HTC WP7 First Generation
DFT HSPL RSPL WP7F3
proudly presents RSPL / HSPL
for phones HTC WP7 First Generation
(Short name is “WP7F
This is first big step to customization and community development for these devices.
Updated release. Revision #3.
- Was added support for 'SCHU1000' and 'PD291200' MIDs
- Removed OTA update inside RSPL and HSPL, this allows to keep HSPL after HTC OTA Zune update.
- Added warning screen about 4.XX and 5.XX
- But still NO support for 4.XX and 5.XX
- Support for CDMA devices: GoldC and SparkW
- Wizard UI: only WWE support remains.
NOTE for ROM chefs:
SparkW custom ROMs must has "SPAW1000" MID instead of "PC402000".
This is done to protect from flashing Spark custom ROM to Spark_W and reversed.
Updated release. Revision #2.
- Improved wizard GUI on non DPI 96 systems.
- Added support for "PD291300", "PD291500" two new Schubert MIDs.
- Replaced RSPL and HSPL for Spark from 1.10 to 1.20.
Initial release. Revision #1.
WARNING TO ALL:
Do NOT use RSPL / HSPL with Mozart 4.XX and other RUU ROMS with MANGO.
All WP7F devices affected: MOZART, GOLD, SCHUBERT, MONDRIAN, SPARK!
It will damage your device. Not a joke.
MORE INFORMATION HERE
Read the next few messages for more information.
This release supports those WP7F devices:
(HTC Pro 7,T7575)
(HD7, HD7S, T9292,T9295,T9296)
*HTC Gold C
*HTC Spark W
Most of these devices have several MIDs
(ModelID, looks like “PC921000
Current release supports only some limited number of MIDs. This was designed to minimize possible harm to user’s devices.
List of supported MIDs:
Gold: “PC92****”, “PC921000”
Mozart: “MOZA1000”, “PD67****”, “PD671000”, “PD671200”
Mondrian: “PD26****”, “PD261000”, “PD261100”
Schubert: “PD29****”, “PD291000”, “PD291100”, "PD291200", "PD291300", "PD291500"
!Please note that on SPL screen MID is only 7 symbols, without last one.!
Programs stops any operations if unknown MID detected. If your device have unknown MID, please report about it in this thread. Specify your MID, device name, ROM versions. It’s nice, if you can give a link to download ROM.
Basic stuffs to know:
is Secondary Program Loader. It allows to flash ROMs to device.
Without working SPL device is fully bricked, you can’t restore it. It’s why all operations with SPL are dangerous.
is Original SPL. This SPL comes with stock ROM and doesn’t allow to flash custom stuffs.
is Reloaded SPL. It load only to RAM, so it doesn’t persistent. It’s enough to soft reset device to get OSPL
is Hard SPL. It’s permanently flashed to internal device memory and replaces OSPL
. After soft reset you still have HSPL instead of OSPL.
This release consists from RSPL
For regular users, who flash ROMs rather rare, it can be enough to use only RSPL
For advanced users and ROM makers, it can be useful to install HSPL
1. Before doing any operations be sure you have battery level more than 50%!
Sometimes in SPL mode WP7F devices DO NOT charge
. You may got a cold brick if it power down during SPL or RADIO update!
2. Stock RUU ROMs have two NBH inside, SPL_Signed and RUU_Signed.
So it's not possible directly flash stock ROM, you need extract files and remove SPL_Signed.nbh at least.
3. Rememeber if you have HSPL
and you flashing stock RUU_Signed.nbh you lost HSPL!
4. Supported OS: Windows XP, Windows Vista, Windows 7.
Be warned, using RSPL may void your warranty.
If you need to send your device to a Repair Centre, make sure that it looks like stock! Install stock official ROM before go to Repair Centre.
This product is free to use at your own risk. We take no responsibility for any conflict, fault, or damage caused by this procedure. No warranties implied or otherwise, are given if you agree to use this product. No problems were found while testing this product on several different devices, your experience may vary.
Use of the Product for commercial purposes is strictly prohibited.
It’s not allowed to make changes to this package; it must be distributed as original release.
Last version (R#3)
Official DFT site (Chinese)