F
fuss132
Guest
Hey guys,
this is still no kernel, it will only optimize your values for touchscreen using The most important thing in this script is the following line:
On my SGS and the SLC is this the best one. Maybe you can try whats working for you as the best and tell it to me so that i can share the best result. I hope the script is now supported by the SGA, i modified it from Galaxy SLC working device... Please give me your feedback.
Can someone of the good Devs from this device tell me if this config is supported by the SGA kernels? Sure it is, but i don´t know under which name
Files attached to this post:
Files should work now on CM7 and Custom/Stock Samsung Firmwares
How to install:
- RootExplorer method; download the attached the_modified_file.zip, unpack it and put the file to /system/usr/idc/mxt224_ts_input.idc. Aaaand Reboot.
- CWM method; download the attached the_flashable_modified_file.zip, put it to your sd-card and flash it through CWM. Aaaand Reboot.
Source:
And why a new Thread?
Very easy. This mod is completely different to my other script. I don´t want to confuse the users ^^
this is still no kernel, it will only optimize your values for touchscreen using The most important thing in this script is the following line:
On my SGS and the SLC is this the best one. Maybe you can try whats working for you as the best and tell it to me so that i can share the best result. I hope the script is now supported by the SGA, i modified it from Galaxy SLC working device... Please give me your feedback.
Can someone of the good Devs from this device tell me if this config is supported by the SGA kernels? Sure it is, but i don´t know under which name
Files attached to this post:
- the_modified_file.zip (THE mod, RootExplorer method)
- the_mod_for_galaxy_ace_flashable.zip (THE mod, CWM method)
Files should work now on CM7 and Custom/Stock Samsung Firmwares
How to install:
- RootExplorer method; download the attached the_modified_file.zip, unpack it and put the file to /system/usr/idc/mxt224_ts_input.idc. Aaaand Reboot.
- CWM method; download the attached the_flashable_modified_file.zip, put it to your sd-card and flash it through CWM. Aaaand Reboot.
Source:
# Copyright (C) 2010 The Android Open Source Project
#
# Licensed under the Apache License, Version 2.0 (the "License");
# you may not use this file except in compliance with the License.
# You may obtain a copy of the License at
#
# http://www.apache.org/licenses/LICENSE-2.0
#
# Unless required by applicable law or agreed to in writing, software
# distributed under the License is distributed on an "AS IS" BASIS,
# WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
# See the License for the specific language governing permissions and
# limitations under the License.
#
# Input Device Calibration File for the Crespo touch screen.
#
# These calibration values are derived from empirical measurements
# and may not be appropriate for use with other touch screens.
# Refer to the input device calibration documentation for more details.
#
# Touch Size
touch.touchSize.calibration = pressure
# Tool Size
# Driver reports tool size as an area measurement.
#
# Based on empirical measurements, we estimate the size of the tool
# using size = sqrt(22 * rawToolArea + 0) * 9.2 + 0.
touch.toolSize.calibration = area
touch.toolSize.areaScale = 22
touch.toolSize.areaBias = 0
touch.toolSize.linearScale = 9.2
touch.toolSize.linearBias = 0
touch.toolSize.isSummed = 0
# All edited parts by fuss132 licensed under GPL
# Visit my profile on xda http://xdaforums.com/member.php?u=3264556
# Thanks for using...
touch.pressure.calibration = amplitude
touch.pressure.source = default
touch.pressure.scale = 0.001
MODULE_DESCRIPTION("Touchscreen Driver");
MODULE_LICENSE("GPL");
# Size
touch.size.calibration = normalized
# Pressure
# Driver reports signal strength as pressure.
#
# A normal thumb touch typically registers about 100 signal strength
# units although we don't expect these values to be accurate.
touch.pressure.calibration = amplitude
touch.pressure.source = default
touch.pressure.scale = 0.001
# Orientation
touch.orientation.calibration = none
And why a new Thread?
Very easy. This mod is completely different to my other script. I don´t want to confuse the users ^^
Last edited: