Originally Posted by Dr-Death

Do i need the DoNotU2hTC before every update? And the Order? : DoNotU2hTC and then dev Unlock / eXit CTRL box? or or vice versa



best regards dr-death

Hi,

You need only once and always follow the dev Unlock / eXit

When receiving an update check if an HTC update is displayed

If not then its ok to update, although not all hTC updates change the bootloader

Regards, ansar

Originally Posted by ansar.ath.gr

Hi,

Most probably the update is not yet available to your country

Can you specify the firmware version before HSPL installation?

Regards, ansar

Hello Ansar, thanks for your fast reply!
Unfortunately I can't remember the firmware version, but I can tell you that in 12/2011 I could perform my phone update through Zune to 7740
(don't know if microsoft and/or htc).
When I installed your NewTech ROM first time, unfortunately I updated via Zune to 7740, that means that there still was present this update.
And before trying to install again HSPL and NewTech, some days later Zune found 8107 update...
Since I was looking to have a fully unlocked device, I tried again the steps in your first post....
At the end I successfully updated offline my device (from 7720 to 7740 and from 7740 to 8107) following Heathcliff74's thread http://forum.xda-developers.com/show....php?t=1306415
I had only to download choice dos command because it's not present in XP and refined a little bit WP7 Update Cab Sender batch file.

Originally Posted by ansar.ath.gr

Hi,

You need only once and always follow the dev Unlock / eXit

When receiving an update check if an HTC update is displayed

If not then its ok to update, although not all hTC updates change the bootloader

Regards, ansar

Hi, the problem ist, i have upated from 7720>7740 per Zune and i saw no extra htc update. perhaps the htc connection setup? after boot, this start automaticly. in the next week, i will try to go back to an old rom with help of your slspl-rom and then i will report. best regards, dr-death

Originally Posted by Dr-Death

Hi, the problem ist, i have upated from 7720>7740 per Zune and i saw no extra htc update. perhaps the htc connection setup? after boot, this start automaticly. in the next week, i will try to go back to an old rom with help of your slspl-rom and then i will report. best regards, dr-death

Hi,

If the bootloader changed then it was an HTC update!!

Regards, ansar

Originally Posted by wg5566

I tried it. But in the trcolor screen, the 'serial' or 'usb' letter does not appear in the lower middle part of the screen. The computuer can not recognise the phone through usb. I keep getting a 'error 260', can not flash it.

See my google translated manual here http://translate.google.cz/translate...brickCesky.htm . If you lost last tricolore line only ("small" halfbrick), you can use "simplified" Y-cable solution (it is easy, not necessary to read CID or make cable yourself, if you want to flash official SPL). I you lost all lines instead first one, you must use Zune backup and U2Mxxxx application first to get some part of SPL 5.xx as part of official update before Y-cable using (to be able force USB Host GoldCard mode), or try OEM cab sending. Without Zune backup it is much more dificult, but, I hope, you have got "small" halfbrick only.

Originally Posted by Martin7Pro

See my google translated manual here http://translate.google.cz/translate...brickCesky.htm . If you lost last tricolore line only ("small" halfbrick), you can use "simplified" Y-cable solution (it is easy, not necessary to read CID or make cable yourself, if you want to flash official SPL). I you lost all lines instead first one, you must use Zune backup and U2Mxxxx application first to get some part of SPL 5.xx as part of official update before Y-cable using (to be able force USB Host GoldCard mode), or try OEM cab sending. Without Zune backup it is much more dificult, but, I hope, you have got "small" halfbrick only.

Thanks a lot for this continuous help Ansar, really!
I've done it through a Y cable half an hour ago.

I just got the CID of the card in windows explorer, by this way: right click disk name, click 'properties', the click 'hardware' tab, double click the disk name again, then in 'detailed information' tab, I found the CID through the dropdown menu. Copied the CID by right click. This CID, need some adjustment: delete the '{', '-' and '}' symbol and replace the first two letters with '00' zero zero. Then at this site, http://psas.revskills.de/?q=goldcard, I got the goldcard.img file, use this file in Gold Card Tool 0.0.5 program to generate the gold card. I used your released Europe stock rom, RUU_Gold_HTC_Europe_1.22.401.01_Radio_5.63.09.13_3 a_22.36.50.15U_by_ansar, copied the ruu_signed.nbh to the card and renamed it to GOLDIMG.nbh.

Originally Posted by wg5566

Thanks a lot for this continuous help Ansar, really!
I've done it through a Y cable half an hour ago.

I just got the CID of the card in windows explorer, by this way: right click disk name, click 'properties', the click 'hardware' tab, double click the disk name again, then in 'detailed information' tab, I found the CID through the dropdown menu. Copied the CID by right click. This CID, need some adjustment: delete the '{', '-' and '}' symbol and replace the first two letters with '00' zero zero. Then at this site, http://psas.revskills.de/?q=goldcard, I got the goldcard.img file, use this file in Gold Card Tool 0.0.5 program to generate the gold card. I used your released Europe stock rom, RUU_Gold_HTC_Europe_1.22.401.01_Radio_5.63.09.13_3 a_22.36.50.15U_by_ansar, copied the ruu_signed.nbh to the card and renamed it to GOLDIMG.nbh.

Hi,

What is the OS in your PC?

Regards, ansar

Originally Posted by ansar.ath.gr

Hi,

What is the OS in your PC?

Regards, ansar

Windows 7 Professional with SP1. Thanks.
Edit: If I am not wrong, CID can also get in Windows XP, in the Hardware Manager, in hardware properties info.

Connection setup starting each time

---

Hello everybody
Each time I turn on my phone, after a while the Connection setup starts...
I tried following this guide http://forum.xda-developers.com/show....php?t=1271963 by Heathcliff74, but it's still doing it...
Is there anyone else experiencing this?

Originally Posted by wg5566

Windows 7 Professional with SP1. Thanks.
Edit: If I am not wrong, CID can also get in Windows XP, in the Hardware Manager, in hardware properties info.

Hi,

In XP and Vista is not the CID that what is revealed

I will check with 7, thnx for commenting!!

Regards, ansar