x10i refuses to turn on

---

I followed these steps

(1) Install .71 Baseband (link) with newest Flashtool (link) - you may use another baseband at your own risk but there is no support, we only test (because we only have) on Baseband 2.1.71 X10i

(2) After Flashtool says "Disconnected" then "Reconnected in Flash Mode", REMOVE CORD and BATTERY and wait ten seconds!

of this guide
after that, when i turn it on it shows the white SE logo and turns off, then turns on and then all over again...
any ideas?)

i used Baseband 2.1.71 and Flastool 0.7.1.0
xperia x10i android 2.1

SE logo? You're on the wrong kernel I think. Take a look at step 3 and Flash the M&M team kCernel

when i connect it to pc it starts showing logo and rebooting

Originally Posted by ashley_

when i connect it to pc it starts showing logo and rebooting

I think that you have rpoblems with getting into flash mode, tri it with different was, prepare everything as decribed before and do notconnect the phone to computer and wait for dialog which is waiting to connect phone with animation and steps how to it.
Do NOT connect phone to PC. Take out battery, put it back. COnnect usb cable to the phone, not second part of cable to PC. Press the Back button and hold it. Then push power on (back button still on hold), green diode will blink for a while. Then you can connect phone to PC and it will enable flash phone flawlessly.

hjoray, it conects in flashmode!)
but something went wrong...when everything is finished, phone should reboot but it simply stays off
heres the log:

15/035/2012 21:35:26 - INFO  - <- This level is successfully initialized
15/035/2012 21:35:26 - INFO  - Flashtool Version 0.7.1.0 built on 2012-05-01 22:07:23
15/035/2012 21:35:26 - INFO  - You can drag and drop ftf files here to start flashing them
15/035/2012 21:35:31 - INFO  - Device disconnected
15/036/2012 21:36:34 - INFO  - Selected X10i_2.1.71_ARO.ftf
15/036/2012 21:36:34 - INFO  - Preparing files for flashing
15/036/2012 21:36:46 - INFO  - Please connect your device into flashmode.
15/038/2012 21:38:12 - INFO  - Device connected with USB debugging off
15/038/2012 21:38:12 - INFO  - For 2011 devices line, be sure you are not in MTP mode
15/038/2012 21:38:30 - INFO  - Device disconnected
15/039/2012 21:39:30 - INFO  - Device connected in flash mode
15/039/2012 21:39:30 - INFO  - Opening device for R/W
15/039/2012 21:39:30 - INFO  - Reading device information
15/039/2012 21:39:30 - INFO  - Phone ready for flashmode operations.
15/039/2012 21:39:30 - INFO  - Start Flashing
15/039/2012 21:39:30 - INFO  - Flashing loader
15/039/2012 21:39:32 - INFO  - Loader : S1_Loader_Root_f851 - Version : R4A024 / Bootloader status : UNROOTABLE / IMEI : 01237900113664
15/039/2012 21:39:33 - INFO  - Flashing kernel.sin
15/039/2012 21:39:35 - INFO  - Flashing fota1.sin
15/039/2012 21:39:36 - INFO  - Flashing fota0.sin
15/039/2012 21:39:37 - INFO  - Flashing amss_fs.sin
15/039/2012 21:39:37 - INFO  - Flashing dsp1.sin
15/039/2012 21:39:45 - INFO  - Flashing amss.sin
15/039/2012 21:39:56 - INFO  - Flashing cache.sin
15/039/2012 21:39:57 - INFO  - Ending flash session
15/039/2012 21:39:57 - INFO  - Flashing finished.
15/039/2012 21:39:57 - INFO  - Please wait. Phone will reboot
15/039/2012 21:39:57 - INFO  - For flashtool, Unknown Sources and Debugging must be checked in phone settings
15/039/2012 21:39:57 - INFO  - Device connected in flash mode
15/042/2012 21:42:53 - INFO  - Flash canceled

	
	
[HTML]
[/HTML]

SOmetimes it happens,no worry

Disconnect phone from computer and turn it on normally. If geen diode will blink, then pull out battery and put back and try to turn it on once again. It will solve it surely

when i turn it on it only shows white se logo then turns off and red led blinks 3 times
and every time it makes some crackly sound before turning off

Originally Posted by ashley_

when i turn it on it only shows white se logo then turns off and red led blinks 3 times
and every time it makes some crackly sound before turning off

Hmm, this doesnt looks good - i think that you will need to reflash the complete ROM now.

Originally Posted by ashley_

when i turn it on it only shows white se logo then turns off and red led blinks 3 times
and every time it makes some crackly sound before turning off

How do you get SE logo with unlocked bootloader? I didn't get that. Maybe your bootloader is locked?

HeliumX10,
which rom shall i use?

LzVebz,
maybe
how can i check it?