Attend XDA's Second Annual Developer Conference, XDA:DevCon 2014!
5,731,426 Members 53,540 Now Online
XDA Developers Android and Mobile Development Forum

FIX for screen separation issue! UPDATED 8/02

Tip us?
 
jam10238
Old
(Last edited by jam10238; 3rd August 2012 at 12:39 AM.)
#1  
Senior Member - OP
Thanks Meter 107
Posts: 161
Join Date: Jan 2012
Default FIX for screen separation issue! UPDATED 8/02

So rather than sending back my Nexus 7, I decided to give something a try. I removed the back casing, which is very easy to do. I used a small flat screwdriver where the "leather" meets the plastic and gently wedged it in. The case popped right open and was easily removed. I then tightened all of the small phillips screws around the outside of the board on the back of the screen.

This immediately cleared up the creakiness and play that i was experiencing on the left side of the screen. I tightened all screws and not just the ones on the left side. Do this at your own risk, obviously, but this immediately rectified my issue!

7/22 update:

So on Friday, I noticed a slight creak returned. I removed the black strip of foam that has been discussed in this thread. Since Friday, with heavy use, no creak, no play, no screen rise I'll update again later in the week to confirm it hasn't returned.

8/02 update:

Since removing the sponge, the play in the screen and the creaks have not returned. I see others havent had as much luck with it but, for me, I can say it did the trick.
The Following 79 Users Say Thank You to jam10238 For This Useful Post: [ Click to Expand ]
 
cwc3
Old
(Last edited by cwc3; 28th July 2012 at 12:22 AM.)
#2  
cwc3's Avatar
Senior Member
Thanks Meter 407
Posts: 524
Join Date: Oct 2011
Location: Medford, OR
Update 1: People are reporting that after a few hours the issue came back. It does appear to be something else causing this. If your issue persists, Call Your Store!
Update 2: Included another guide in this post to try, thank you Luxferro & Evo_Shift
Update 3: Most of us Play Store people are closing in on 15 day replacement time. It's quick & painless, and you still get to use your tablet while the other one is being shipped. Call them, RMA it, get it taken care of.

Update 4: Added Washer Fix Guide. Received my new replacement from the google store. Worse than my older one. Uploaded a video below. Google told me to google the fix for it and try it.

NOTE: Me & Jam are not responsible for what damage you may cause. Nobody has noticed any warranty seals being broken.

______________________________________

Do I have screen separation?
______________________________________


http://www.7nex.us/wp-content/galler...ts/buldge5.jpg
______________________________________

Guide One - Washer Fix by dilldoe
______________________________________

Main Idea: http://imgur.com/QbGxi | Original Post: http://forum.xda-developers.com/show...&postcount=638

UPDATE: PICTURES & GUIDE - http://forum.xda-developers.com/show...50&postcount=1
Using the thin plastic from a pill blister (allergy pills were right in front of me when I was doing this) I created a washer to space out the frame & screen.

Just cut a rectangle out and punch a hole at the end for the screw to go thru. I just used a sewing needle on a sewing machine, like a drill press, to make a starter hole and my smallest screwdriver to widen it. With the screwdriver still in the hole, I just ran my knife around it to trim off the excess plastic.

WHY A LONG RECTANGLE? so you can insert it and hold it in place while you work. don't want it accidentally falling into the device.

now just slide that UNDER the top frame and screw it back together. MAKE SURE YOU STOP ONCE IT'S SNUG. the screen should now be lower than the side bezel.

Do this to all the spots that are lifting. I just did mines on the lower left and upper right, since they both had slight lift.

After you're done screwing it all down, trim off the excess so you can put the back cover back on, not flush to the frame, just enough so you can hold it if you need to remove it.

Did this last night and this afternoon, still no returning lift.

edit: depending on how much lift you have, you might have to use 2 or more to fill the gap (or use something thicker like used gift cards)
Follow ups:
http://forum.xda-developers.com/show...&postcount=677
http://forum.xda-developers.com/show...&postcount=710
http://forum.xda-developers.com/show...&postcount=700

______________________________________

Guide Two - Simple Tighten by cwc3/jam10238
______________________________________
1) Grab something that isn't going to mar your nice silver plastic. People have been using guitar picks & even their fingernails
2) Stick that non-marring object between like seen here: http://guide-images.ifixit.net/igi/C...hEPlBI2.medium (they have a white cover while we have a black one)
3) Start sliding that object between the two, you will notice them starting to pop up. Try not to pry if you can, I had to a little.
4) Should now look like this: http://guide-images.ifixit.net/igi/1...UKYoEVx.medium
5) Tighten all the screws around the outside (Pretty much eye glasses size), on the black plastic and metal. Not too tight, or you might cause back-light bleed &/or strip the screw. In my case most were a little loose.
6) When putting the case back on, be sure your not just starting flat. Start at a angle, for example, with the right side portrait. Push/Pop it back on going around the tablet.

Pictures I took taking it apart:
______________________________________

Guide Three - Advanced Tighten by Luxferro
______________________________________

Original Post: http://forum.xda-developers.com/show...4#post29022274

1) Loosen all the screws around the outside w/ the panel on a flat hard surface (hard cover book)
2) Let the panel re-seat itself a bit
3) Just barely tighten all the screws.
4) Then repeat the tightening once they are all done to snug them up (not too much!). It should make your screen look perfect.
4a) After a bit of use you might need to snug them up once more - if the glass starts popping up again.

I tried this method of losening the screws after just tightening them failed me. And so far over 12 hours later my device still is good
Follow up:
http://forum.xda-developers.com/show...&postcount=235

________________________________________


Interesting Links:
The Following 39 Users Say Thank You to cwc3 For This Useful Post: [ Click to Expand ]
 
SS2006
Old
#3  
SS2006's Avatar
Senior Member
Thanks Meter 90
Posts: 1,480
Join Date: Aug 2008
Location: London, Ontario
Post a vid!

---------- Post added at 12:55 PM ---------- Previous post was at 12:55 PM ----------

So the problem most of us have is cause ASUS didn't tighten some screws.. hahh
 
_MetalHead_
Old
#4  
_MetalHead_'s Avatar
Senior Member
Thanks Meter 1999
Posts: 5,075
Join Date: Jun 2010
Location: Chicagoland
Thanks for TOFTT!

When you snapped the case back on there was no evidence that you opened it?
\m/(-_-)\m/
The Following User Says Thank You to _MetalHead_ For This Useful Post: [ Click to Expand ]
 
jam10238
Old
#5  
Senior Member - OP
Thanks Meter 107
Posts: 161
Join Date: Jan 2012
Quote:
Originally Posted by cwc3 View Post
You brave, brave man.

For anyone as brave as him, here is a tear down guide: http://www.ifixit.com/Teardown/Nexus-7-Teardown/9623/1
Ha! It really sounds a lot worse than it is. Removing my Galaxy Nexus battery cover is almost as difficult!

Sent from my Galaxy Nexus using Tapatalk 2
The Following User Says Thank You to jam10238 For This Useful Post: [ Click to Expand ]
 
laverdure#1
Old
#6  
Member
Thanks Meter 13
Posts: 50
Join Date: Jul 2012
Quote:
Originally Posted by jam10238 View Post
So rather than sending back my Nexus 7, I decided to give something a try. I removed the back casing, which is very easy to do. I used a small flat screwdriver where the "leather" meets the plastic and gently wedged it in. The case popped right open and was easily removed. I then tightened all of the small phillips screws around the outside of the board on the back of the screen.

This immediately cleared up the creakiness and play that i was experiencing on the left side of the screen. I tightened all screws and not just the ones on the left side. Do this at your own risk, obviously, but this immediately rectified my issue!
Brave indeed! Tempted to do this since I have the same problem but 1) don't wanna wait 1h on hold trying to get an RMA and 2) who knows when I'd be getting a new one.

In case I try this, and it ends up not fixing the issue and I decide to send it back later, do you think Google would be able to tell that device has been opened and potentially refuse the exchange?

Thanks
 
neilrl79
Old
#7  
neilrl79's Avatar
Senior Member
Thanks Meter 107
Posts: 582
Join Date: Aug 2010
Location: Maryland

 
DONATE TO ME
I might give this a try tonight after having an adult beverage to calm my nerves.
The Following 2 Users Say Thank You to neilrl79 For This Useful Post: [ Click to Expand ]
 
Pithism
Old
#8  
Senior Member
Thanks Meter 61
Posts: 1,014
Join Date: Dec 2010
Location: Boston, MA
Thank you for doing it. I'll give it a go when I get home. Did you use a regular flat head or a plastic device friendly one?

Sent from my Galaxy Nexus using xda premium
 
jam10238
Old
#9  
Senior Member - OP
Thanks Meter 107
Posts: 161
Join Date: Jan 2012
Quote:
Originally Posted by laverdure#1 View Post
Brave indeed! Tempted to do this since I have the same problem but 1) don't wanna wait 1h on hold trying to get an RMA and 2) who knows when I'd be getting a new one.

In case I try this, and it ends up not fixing the issue and I decide to send it back later, do you think Google would be able to tell that device has been opened and potentially refuse the exchange?

Thanks
I dont think so, there is absolutely ZERO warranty tape or anything that is standard on electronics these days. Its literally like a big battery cover. I can post a video shortly of the process.

Sent from my Galaxy Nexus using Tapatalk 2
The Following 3 Users Say Thank You to jam10238 For This Useful Post: [ Click to Expand ]
 
jam10238
Old
#10  
Senior Member - OP
Thanks Meter 107
Posts: 161
Join Date: Jan 2012
Quote:
Originally Posted by Pithism View Post
Thank you for doing it. I'll give it a go when I get home. Did you use a regular flat head or a plastic device friendly one?

Sent from my Galaxy Nexus using xda premium
Just a very small standard precision flat head. Fingernails may even work it was that simple.....

Sent from my Galaxy Nexus using Tapatalk 2

The Following User Says Thank You to jam10238 For This Useful Post: [ Click to Expand ]
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes