My MDA II died after ROM 1.60 upgrade

---

:evil:
Hi guys,
I need some serious help here. Today I tried to upgrade my MDA II with the latest 1.60 ROM. Somehow during the upgrade something went wrong and my computer frooze and needed a reset. This was in the beginning 10 minutes of the ROM upgrade and my the screen of my PPC went off. After the reboot of my workstation I could not get my MDA II to connect to my workstation. The MDA is completely useless now. The only thing I have on the screen is:
Serial (or USB) on top of the screen (with no backlight) and at the bottem of the screen Version 1.01.
I can't soft reset of hard reset. I took the battery out and waited for almost 30 minutes but I still can't turn the thing on nor can I soft or hard reset. I can't thing of anything else that I can do and I just sold my Loox yesterday so now I'm lost!
Anybody with a good suggestion??
Please help.
Regards,
Wouter
The Netherlands

I think it's a way to use a SD-card with a Rom on it.
Looks like Your bootloader is still working and can reflash a rom to Your device.
Now You have to find somone with an 64MB SD-card to put a rom on it and reflash Your device.

With best regards
Jens

Hi Jens,
I think my bootloader is not working anymore. I tried to do a hard reset a dozen times but the bootloader menu doesn't come up. But thanks for suggesting though.
Wouter

Hi wouterk,

I don't know if this would be of any help, but you've got nothing to lose now.

I've got a similar error that the RUU program asked me to remove my XDA II from the cradle and right after that, the XDA II screen freeze at "Seria 1.01", same as yours.

So I put my XDA II back to the cradle and from my PC, I clicked Control Panel > System > Device Manager > and here my XDA II was recognized as an unknown device, so I updated the MS USB Sync driver.

After the driver update, I rerun the RUU and the ROM upgrade went fine. Now I have my XDA II back alive and kickin' with the new MDA ROM. At least this works for mine and hope it would also work for yours as well.

HTH.

Hi Joparp,
Of course I gave your suggestion a try. But too bad it didn't work for me like that :? . I remebered that when my workstation crashed, after the reboot it found a new USB device (my cradle?) but I couldn't get your sollution to work for me. But I still have hopes. Tomorrow evening I'll meet a guy who can fix my problem (keep my fingers crossed....). So I feel reasonable relaxed now. :P
It is nice to see that so many people responded to my problem. I posted my problem on three different sites and many people responded. That was a nice feeling! I keep this thread posted about the result of tomorrow.
B.t.w did you install the 1.60 ROM eventually?
Wouter

Hello wouterk

well, i'm sorry about this and i guess the safest way to do ROM update thru SD Card.

i do agree with jenson suggestion and i can't see any other way to resolve this problem which i hope will work here are the steps as follows :-

ask any one who has MDA II device, 64MB SD Card and SD Card reader to backup his/her ROM and Post it for you somewhere where you can download it and write it to SD Card.

ofcourse he/she if using Windows will need serial cable and hyper terminal software which normally can be fount under start/programs/Accessories/Communication otherwise download from http://www.hilgraeve.com/htpe/index.html
get the device into Bootloader Mode ( power button+any direction+reset )
Connected via Serial cable and use these setting 115200 baud, 8n1, direct to com1 port or maybe com2 it depends on which port they use
type d2s command to backup ROM to SD Card which i recommend 64MB SD card formatted and when done you will see something look like this

D:Waiting for card insert.........
SDetected one card
SD:ready for transfer OK
Total card size=3D40000ze=0
SDCARDD2S+,cStoragePlatformType=FF
************************************************** ******************************
***********************************************
Store image to SD/MMC card successful.
SER>


then reset the device and get SD card reader and insert this card into the reader and use ntrw image reading and writing tool

if you don't have it you can download it from here http://www.tamiminet.com/othman/ntrw.exe

from the command line run ntrw read MDAII.nb1 E:

This assumes your SD card reader has drive letter E:

now you will have new file which is MDAII.nb1 it's about the size of the SD card zip it and post it somewhere so he/she can Download it and unzip it then write it back to SD Card using this command b]ntrw write MDAII.nb1 E:[/b]

again this assumes your SD card reader has drive letter E:

when done go into bootloader mode ( power button+reset ) with SD card inserted, hit camera button and flash your device with rom which is on SD Card

if you don't have serial cable you still can do it using Linux with cardle and thanks for bio and few other cool guys who mentioned this hints on other thread
put your device in bootloader mode
connect via cradle
use any terminal (minicom) to connect to the used port (/dev/ttyUSB0)
- you should see something like 'USB>' or 'SER>'
put an SD Card into device
type d2s on command prompt

wait untill you see Store image to SD/MMC card successful

i don't think this will include the Applications on the Extended ROM but no problem this can be done later.

i hope this could help to get back you device to life.


best regards and good luck.



Othman
Riyadh, Saudi Arabia

It is working again!

---

:lol:
Hi guys,
Thanks to Akira my MDA II is working again. Everything is working again exept for the bluetooth communication with my Emtac bluetooth GPS. That problem still remains in my case. I even did another hard reset but still the same problem. I then put the Towa fix again on it and now I can use my GPS again.
So thank you all guys!
Wouter