This script will make your phone faster and smoother, i tested it and it worked for me on my Ace 2
This fixes bad memory management on our JB
Full totorial is HERE, it is little messy so i made this for some less experienced users.
All credits goes to Zeppelinrox
Requirements:
1. Rooted Device with custom ROM (Italian Job or Kyrillos for Ace 2)
2. Script manager (You can also use terminal emulator or ADB shell)
3. Busybox over 1.16.2 (included in Italian Job and Kyrillos)
Installation:
1. Download latest script from this page
Note: To download script : Right Click ---> Save as
2. Transfer it to your /sdcard (or anywhere else)
3. There are 3 ways to open script :
a) Using Script Manager
Open Script manager and locate script, press it and give root acces ( su icon , turns green when you press it ) and press run
b) Using Terminal Emulator
To run this script in terminal emulator you have to write following lines
c) Via ADB
In cosole write :
Note: if you put script in other folder you need to write it etc. if you have folder named supercharger on internal memoy and you put script there you have to write:
4. Than all you need to do is follow instructions when you run script, everything is fully explained.
5. Reboot when you finish
At this point skip to step 9. if you are running GB!
Continue for JB
When you finish this all you will not be able to supercharge 100% because we need to mod services.jar file.
Here is what to do next:
6. Download Ultimatic Jar Patcher from THIS thread (Ultimatic_Jar_Patcher_Tools_RC6_ALL_DEX_ALL_OSes_NO_FLASH.zip)
7. Turn on USB debugging ( Developer options > under Debugging check USB debugging ) and Run Supercharger V6 on your phone
8. Connect phone to PC and run Ultimatic Jar Patcher ( Extract attached file and run ultimatic_run_patcher_adb.bat) and follow instruction. Again is everything fully eyplained when you run it.
9. Run SuperClean and Reboot.
10. Using script manager navigate to /data/99supercharger.sh and select "run as root" ( su icon ) , and "Start on boot"
Note: To test if script runs after reboot open supercharger v6 script and see info under the menu
11. YOU HAVE SUPERCHARGED ANDROID DEVICE! Now it depends on you what settings will you use. Hope i helped
If you have any problems ask here or contact me via pm.
My settings ( They are shown when you run script ) :
Minfree values : 8,16,180,200,220,255 are best so far I discovered.
Really good memory management with them !
P.S.
If you got better performance with other settings share it here !
If this was helpfull press THANKS button
This fixes bad memory management on our JB
Full totorial is HERE, it is little messy so i made this for some less experienced users.
All credits goes to Zeppelinrox
Requirements:
1. Rooted Device with custom ROM (Italian Job or Kyrillos for Ace 2)
2. Script manager (You can also use terminal emulator or ADB shell)
3. Busybox over 1.16.2 (included in Italian Job and Kyrillos)
Installation:
1. Download latest script from this page
Note: To download script : Right Click ---> Save as
2. Transfer it to your /sdcard (or anywhere else)
3. There are 3 ways to open script :
a) Using Script Manager
Open Script manager and locate script, press it and give root acces ( su icon , turns green when you press it ) and press run
b) Using Terminal Emulator
To run this script in terminal emulator you have to write following lines
Code:
su
sh /sdcard/V6*
c) Via ADB
In cosole write :
Code:
adb shell
su
sh /sdcard/V6*
Note: if you put script in other folder you need to write it etc. if you have folder named supercharger on internal memoy and you put script there you have to write:
Code:
su
sh /sdcard/supercharger/V6*
4. Than all you need to do is follow instructions when you run script, everything is fully explained.
5. Reboot when you finish
At this point skip to step 9. if you are running GB!
Continue for JB
When you finish this all you will not be able to supercharge 100% because we need to mod services.jar file.
Here is what to do next:
6. Download Ultimatic Jar Patcher from THIS thread (Ultimatic_Jar_Patcher_Tools_RC6_ALL_DEX_ALL_OSes_NO_FLASH.zip)
7. Turn on USB debugging ( Developer options > under Debugging check USB debugging ) and Run Supercharger V6 on your phone
8. Connect phone to PC and run Ultimatic Jar Patcher ( Extract attached file and run ultimatic_run_patcher_adb.bat) and follow instruction. Again is everything fully eyplained when you run it.
9. Run SuperClean and Reboot.
10. Using script manager navigate to /data/99supercharger.sh and select "run as root" ( su icon ) , and "Start on boot"
Note: To test if script runs after reboot open supercharger v6 script and see info under the menu
11. YOU HAVE SUPERCHARGED ANDROID DEVICE! Now it depends on you what settings will you use. Hope i helped
If you have any problems ask here or contact me via pm.
My settings ( They are shown when you run script ) :
Code:
================================================
Prior Scrolling Speed has been applied - 0
================================================
Kernel & Virtual Memory Tweaks are Rock Hard!
================================================
Miscellaneous and SD Card Speed Tweaks - YES!
================================================
3G TurboCharger Enhancement(3GTC Addon)- YES!
================================================
Engine Flush-O-Matic - Enabled @ Every - 2hrs
================================================
Fix Alignment (Dual Tool) Runs On Boot - NO!
================================================
Fix Emissions (Fixes FCs) Runs On Boot - YES!
================================================
Wheel Alignment(ZipAlign) Runs On Boot - YES!
================================================
Detailing(Clean Database) Runs Every 5 Boots!
================================================
.
.
.
================================================
Launcher is DIE-HARD! ie. SUPERCHARGED! 25%
================================================
SuperCharger ADJ Entries ARE Patched In! 50%
================================================
OOM Grouping Fixes ARE In Effect! 75%
That means the boot script ran!
================================================
Current Values MATCH Prior SuperCharge! 100%
.
.
.
================================================
Current Minfrees = 8,16,180,200,220,255 MB
Prior V6 Minfrees = 8,16,180,200,220,255 MB
================================================
You have 624 MB of RAM on your device...
...768 HP settings are recommended!
.
.
.
================================================
SuperCharger Service is Installed!
================================================
BullerProof Apps Service is Installed!
================================================
/init.d/97BulletProof_Apps is NOT Running!
================================================
Engine Flush-O-Matic is ON & NOT in RAM!
================================================
Nitro Lag Nullifier is Installed!
================================================
.
.
.
================================================
SuperCharger Level: 100% SuperCharged!
================================================
Minfree values : 8,16,180,200,220,255 are best so far I discovered.
Really good memory management with them !
P.S.
If you got better performance with other settings share it here !
If this was helpfull press THANKS button
Last edited: