Attend XDA's Second Annual Developer Conference, XDA:DevCon 2014!
5,810,631 Members 45,387 Now Online
XDA Developers Android and Mobile Development Forum

Need help ... About usb cable p1000 or p3100 ...

Tip us?
 
fooiskandar
Old
#1  
fooiskandar's Avatar
Senior Member - OP
Thanks Meter 71
Posts: 422
Join Date: May 2013
Location: Kuningan
Default Need help ... About usb cable p1000 or p3100 ...

Need help about usb cable ... Could anyone to show inside the cable an tell me how to repair the usb cable ...

The question is anyone have usb cable schematic for p1000 or p3100 ...

Sent from my GT-P3100
Sorry for my bad english ... Don't forget to HIT THANKS button !!!
 
fooiskandar
Old
#2  
fooiskandar's Avatar
Senior Member - OP
Thanks Meter 71
Posts: 422
Join Date: May 2013
Location: Kuningan
Full up ... Need help ... Please ...

Sent from my GT-P3100
Sorry for my bad english ... Don't forget to HIT THANKS button !!!
 
blue_drt29
Old
#3  
blue_drt29's Avatar
Member
Thanks Meter 36
Posts: 46
Join Date: Feb 2012
Quote:
Need help about usb cable ... Could anyone to show inside the cable an tell me how to repair the usb cable ...

The question is anyone have usb cable schematic for p1000 or p3100 ...

i create this fixing guideline because i've been confuse when my cable charger was broken and i cant find any instruction on search engine about fixing this stuff.
Cable for Samsung Galaxy Tab is similar with my actually gadget, Galaxy note 10.1 [GT-N8000].

OK .... lets start it
Step 1: what you need

1. broken cable it self
2. cutter
3. tweezers
4. solder set

last touch misc [i use]
1. tape
2. ethyl cyanoacrylate [liquid glue]
3. tissue or fabric

Step 2: Cut the vessel













Step 3: Connect the unconnected





watch carefully for unconnect cable ...

find it and soldering this on to this rite place
in my stuff ... the rite place is the tin point are not have any wire go to front ... only tin spot ... look my sketch for info side by side cable

use only hot tip soldering tools for open the wire ... [ 1st i use razor and unlucky to cut them off .. lol ]

check this 1st before you assemble all opened pieces together

i have two charger and both was end with this same problem ... unconnect green wire
is this some of samsung failed charger product?

Step 4: Test that

before plug in cable charger to your device ... look on your battery percentation ... remember it ... plug your charger in and wait till view minutes. if everything correct, the battery percentation would rise.

MAKE SURE its truly fixed !!!

if after more than three minutes and battery percentation doesnt goes up ... re check your work and find something not connected well .... and fix it

to make sure everything was back to normal ... let this repaired cable make your device fully charge.

good?

ok ... lets do final step

Step 5: Finishing touch





until all have done and runing normal ... do this step to make our repaired cable tough enough for our daily use

after all part was assembled .... use your tape to covered all this stuff surface to avoid of glue damaging important parts if one time you need to repairing again.

basicly ... depend on what material you want to use to covering this stuff
[ e.g epoxy, resin, palstic, putty, product package, etc ]

i choose ethyl cyanoacrylate and combine it with cut off fabric .... put lill bit glue to stick fabric before we can covering this area .... until it covered by fabric .... drop liquid glue on it .... only to make fabric wet and stick to charger

do it layer by layeruntil you feel enough .... and let it dry and being hard

and all done

thanx for looking

and perhaps this is usefull for you
The Following 2 Users Say Thank You to blue_drt29 For This Useful Post: [ Click to Expand ]
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes