Post Reply
Plug

[FIRMWARE] [UNBRICK] WALTON Primo S2 Official Firmware, Flashtools & Drivers

16th April 2014, 05:08 AM   |  #1  
tuxboy's Avatar
OP Member
Flag Dhaka
Thanks Meter: 120
 
40 posts
Join Date:Joined: Dec 2013
Donate to Me
More
If you somehow brick your WALTON Primo S2 device during development or testing out some crazy stuff, this firmware should come in handy. Even if the bootloader gets killed, your phone can be recovered using this method. Or you can just flash stock firmware when you want it.



Downloads
INSTRUCTIONS (IF NOT BRICKED)
Quote:

  1. Download and Extract the ZIP archive linked above.
  2. Browse to the Primo S2 Official Firmware/Drivers folder. Double-click on GN_QC_EN_Driver_V1.1.0.0.exe to install the driver.
  3. Connect your phone via USB and make sure USB Debugging is turned on, on your phone.
  4. Browse to the Primo S2 Official Firmware/Software folder and extract the file PrimoS2_0402_T5281.7z. (You need 7zip installed for this)
  5. Extract the file Primo S2 Official Firmware/Flash tools/GNQC_DownLoadV1.6.4.0_EN.rar.
  6. Double click on the GNQC_DownLoad.exe located inside the folder you just extracted. You should see a window like below. (click the image to see larger image)
    Click image for larger version

Name:	0.png
Views:	348
Size:	57.4 KB
ID:	2689033
  7. Now click on AP Browse and select the folder Primo S2 Official Firmware/Software/PrimoS2_0402_T5281/PrimoS2_0402_T5281
  8. Then click on BP Browse and select the folder Primo S2 Official Firmware/Software/PrimoS2_0402_T5281/PrimoS2_0402_T5281/bp_image
  9. Set DL mode to General download. Make sure the "Backup or Restore QCN" checkbox is unchecked.
    Click image for larger version

Name:	1.png
Views:	236
Size:	60.8 KB
ID:	2689034
  10. Now click the DownLoad button, the download process should start.
    Click image for larger version

Name:	2.png
Views:	171
Size:	65.0 KB
ID:	2689035
  11. After a while, the flashing should complete and you will see a confirmation message. Disconnect the phone, pull out the battery, put it in again and push the power button!
    Click image for larger version

Name:	3.png
Views:	158
Size:	49.7 KB
ID:	2689036

Instructions (IF Bricked)
Quote:

  1. Download and Extract the ZIP archive linked above.
  2. Browse to the Primo S2 Official Firmware/Drivers folder. Double-click on GN_QC_EN_Driver_V1.1.0.0.exe to install the driver.
  3. If your device is bricked, nothing except the lights of the hardware buttons should light up. So, make sure it is bricked, switch on your phone and connect it via USB cable.
  4. Browse to the Primo S2 Official Firmware/Software folder and extract the file PrimoS2_0402_T5281.7z. (You need 7zip installed for this)
  5. Extract the file Primo S2 Official Firmware/Flash tools/GNQC_DownLoadV1.6.4.0_EN.rar.
  6. Double click on the GNQC_DownLoad.exe located inside the folder you just extracted. You should see a window like below. (click the image to see larger image)
    Click image for larger version

Name:	0.png
Views:	348
Size:	57.4 KB
ID:	2689033
  7. Now click on AP Browse and select the folder Primo S2 Official Firmware/Software/PrimoS2_0402_T5281/PrimoS2_0402_T5281
  8. Then click on BP Browse and select the folder Primo S2 Official Firmware/Software/PrimoS2_0402_T5281/PrimoS2_0402_T5281/bp_image
  9. Set DL mode to General download. Make sure the "Backup or Restore QCN" checkbox is unchecked.
    Click image for larger version

Name:	1.png
Views:	236
Size:	60.8 KB
ID:	2689034
  10. Now click the DownLoad button, the download process should start.
    Click image for larger version

Name:	2.png
Views:	171
Size:	65.0 KB
ID:	2689035
  11. After a while, the flashing should complete and you will see a confirmation message. Disconnect the phone, pull out the battery, put it in again and push the power button!
    Click image for larger version

Name:	3.png
Views:	158
Size:	49.7 KB
ID:	2689036

Credits
  • Imran Imu, Walton Mobile
Attached Thumbnails
Click image for larger version

Name:	Untitled.png
Views:	92
Size:	56.3 KB
ID:	2689047  
Last edited by tuxboy; 23rd April 2014 at 02:30 AM.
The Following 12 Users Say Thank You to tuxboy For This Useful Post: [ View ]
16th April 2014, 05:39 AM   |  #2  
esarve's Avatar
Senior Member
Flag Munshiganj
Thanks Meter: 23
 
164 posts
Join Date:Joined: Jun 2013
Donate to Me
More
নিজে বানাইছো নাকি ফ্ল্যাশ টুল টা?
16th April 2014, 06:13 AM   |  #3  
tuxboy's Avatar
OP Member
Flag Dhaka
Thanks Meter: 120
 
40 posts
Join Date:Joined: Dec 2013
Donate to Me
More
Prompt
Quote:
Originally Posted by esarve

নিজে বানাইছো নাকি ফ্ল্যাশ টুল টা?

No! Made by Gionee.
17th April 2014, 02:32 PM   |  #4  
OdSazib's Avatar
Member
Flag Dhaka
Thanks Meter: 102
 
73 posts
Join Date:Joined: Oct 2013
Donate to Me
More
Quote:
Originally Posted by tuxboy

If you somehow brick your WALTON Primo S2 device during development or testing out some crazy stuff, this firmware should come in handy. Even if the bootloader gets killed, your phone can be recovered using this method. (If nothing except the keypad lights turn on, then you killed the bootloader). So, let's see how we can revive a dead Primo S2.



Downloads


Instructions
  1. Download and Extract the ZIP archive linked above.
  2. Browse to the Primo S2 Official Firmware/Drivers folder. Double-click on GN_QC_EN_Driver_V1.1.0.0.exe to install the driver.
  3. If your device is bricked, nothing except the lights of the hardware buttons should light up. So, make sure it is bricked, switch on your phone and connect it via USB cable.
  4. Browse to the Primo S2 Official Firmware/Software folder and extract the file PrimoS2_0402_T5281.7z. (You need 7zip installed for this)
  5. Extract the file Primo S2 Official Firmware/Flash tools/GNQC_DownLoadV1.6.4.0_EN.rar.
  6. Double click on the GNQC_DownLoad.exe located inside the folder you just extracted. You should see a window like below. (click the image to see larger image)
    Attachment 2689033
  7. Now click on AP Browse and select the folder Primo S2 Official Firmware/Software/PrimoS2_0402_T5281/PrimoS2_0402_T5281
  8. Then click on BP Browse and select the folder Primo S2 Official Firmware/Software/PrimoS2_0402_T5281/PrimoS2_0402_T5281/bp_image
  9. Set DL mode to General download. Make sure the "Backup or Restore QCN" checkbox is unchecked.
    Attachment 2689034
  10. Now click the DownLoad button, the download process should start.
    Attachment 2689035
  11. After a while, the flashing should complete and you will see a confirmation message. Disconnect the phone, pull out the battery, put it in again and push the power button!
    Attachment 2689036

Credits
  • Imran Imu, Walton Mobile

Thanks Ani vai for your awesom writing

Grateful to WaltonBD, Imran vai
The Following 3 Users Say Thank You to OdSazib For This Useful Post: [ View ]
Post Reply Subscribe to Thread

Tags
primo s2, stock rom, walton
Previous Thread Next Thread
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes


Top Threads in Miscellaneous Android Development by ThreadRank