Welcome to XDA

Search to go directly to your device's forum

Register an account

Unlock full posting privileges

Ask a question

No registration required
Post Reply

Info 2 [SHG-i537] ML2 SafeStrap Flashing Guide

OP Bleedin_Sarge

15th May 2014, 07:14 PM   |  #1  
Bleedin_Sarge's Avatar
OP Member
Thanks Meter: 6
 
48 posts
Join Date:Joined: Dec 2013
More
I cannot and will not be held responsible for anything that may happen due to you following this guide. You are directly
responsible for anything that you instruct your device to do. By following this guide, you accept full and complete
responsibility for whatever the outcome is.


After much trial and error, this guide should help those of you stuck on stock ML2 get to running ROMs through SafeStrap 3.71

Before anything, a thanks goes to spegelius and Devo7v for helping with the much needed files. Without them, I would not
have gotten this far.

Requirements:
* You need to be on 4.3 ML2 as your stock firmware
* You need to be rooted. If you are not, read this: http://forum.xda-developers.com/show....php?t=2690133
* You will need to have SafeStrap 3.71 installed. Check here: http://goo.im/devs/Hashcode/jflteatt-active/safestrap
**Verify that you are using the SHG-i537 BEFORE installing anything**

Once you have that done, boot into recovery and create a new ROM slot.
It will take a few minutes for the slot to create and setup.
Once it has setup, grab your favorite TW ROM and flash 'er to the slot. (I used HyperDrive)
Now, flash the ML2 modules, followed by the MF5 camera prop archive.
Now flash the GPIO keys archive.
Clear the dalvik and cache, and reboot.

This should give you hardware keys, wifi, bluetooth, NFC, and Camera.

I know this is not the most comprehensive guide out there, but it should be enough to get you up and running.
Attached Files
File Type: zip I9295_MF5_camera_props.zip - [Click for QR Code] (2.62 MB, 33 views)
File Type: zip gpio-keys_I537.zip - [Click for QR Code] (152.7 KB, 30 views)
The Following User Says Thank You to Bleedin_Sarge For This Useful Post: [ View ]
18th May 2014, 07:13 PM   |  #2  
Senior Member
Thanks Meter: 66
 
294 posts
Join Date:Joined: Jan 2011
is necessary to flash the compatibility pack on hyperdroid ? , is the stock camera working with any rom?
thanks for the guide im new here and i was a little bit lost with the rom flashing

Sent from my Nexus 4 using XDA Premium 4 mobile app
20th May 2014, 04:35 PM   |  #3  
Bleedin_Sarge's Avatar
OP Member
Thanks Meter: 6
 
48 posts
Join Date:Joined: Dec 2013
More
If you plan on using the device with AT&T, the compat pack is a must. And as far as I have tested, no the stock camera does not work.

Sent from my SAMSUNG-SGH-I337 using XDA Free mobile app
The Following User Says Thank You to Bleedin_Sarge For This Useful Post: [ View ]
20th May 2014, 07:03 PM   |  #4  
Senior Member
Thanks Meter: 66
 
294 posts
Join Date:Joined: Jan 2011
sad for the stock camera but did you make it work with another apk ? if so which one i could use?

Sent from my Nexus 4 using XDA Premium 4 mobile app
21st May 2014, 06:11 PM   |  #5  
Bleedin_Sarge's Avatar
OP Member
Thanks Meter: 6
 
48 posts
Join Date:Joined: Dec 2013
More
I installed the Google Cam, and the AOSP gallery.

Sent from my SAMSUNG-SGH-I337 using XDA Free mobile app
The Following User Says Thank You to Bleedin_Sarge For This Useful Post: [ View ]
22nd May 2014, 03:28 AM   |  #6  
Senior Member
Thanks Meter: 66
 
294 posts
Join Date:Joined: Jan 2011
ok cool ty ill try that

Sent from my Nexus 4 using XDA Premium 4 mobile app
22nd May 2014, 06:08 AM   |  #7  
Bleedin_Sarge's Avatar
OP Member
Thanks Meter: 6
 
48 posts
Join Date:Joined: Dec 2013
More
Not a prob. My i537 runs like a champ on HyperDrive with the AOSP addons.

Sent from my SAMSUNG-SGH-I337 using XDA Free mobile app (Really an i537, jus now saw it says i337...s4 build prop)

Post Reply Subscribe to Thread
Previous Thread Next Thread
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes