thank you for this nice post
it helps many ppls to get rid from unwanted things..........

Stops at "Loading"

---

Please HELP!!

I have the exact same problem as some others, like my device stops at "Loading" if I try to flash anything via SD! And I have no other way, because I flashed android NAND!
I tried everything, used MTTY for formating successfully, but nothing helped!

PLEASE HELP US!!

I hate the Tilt2, worst piece of ****, and worst purchase Ive ever made

---

So how exactly do I do this?

For the AT&T Tilt with any SPL below 1.93 the proper sequence for RUUNBH errors is:
cmd> set 16 0
cmd>boot

Doesn't make sense to me, im a nublar.

You saved me people and my beloved Kaiser, which was drowned & immerged in water twice in its life

Edit: I too was locked with a "loading..." screen. I just removed the Kaiser diag file from my sd, and just left the rom nbh I wanted to flash. Good luck.

dwny said on 21st February 2008, 01:52 PM:

The only time you have to worry is if your device does not power up at all


...is worryin' all i can do for my htc touch pro to work
it's dead dead

Originally Posted by GSLEON3

Okay, MTTY is a very useful tool & can help save your butt on many occasions.

A few of those occasions include:

1. Bad flash or installation of HardSPL
2. Bad Flash of a ROM.

There are several other problems that can arise & be mended with the use of MTTY. The most common use is for recovery of any flash process resulting in an RUUBNH error.

For most of these error you want to use MTTY to reboot the low level CE of your device to flush out any bad blocks.

Use of MTTY to recover from these errors is usually simple. The basic outline of how to use MTTY to resolve these errors is as follows:

1. Right click on the quicklaunch activesync icon on the lower left quadrant of your pc. (You can also just open up the A/S program)
2. Select Connection Settings.
3. Uncheck the box labeled "Allow USB Connections" & then Click "OK".
4. Open MTTY & select "USB from the Port options drop down menu.
5. Select RTS/CTS from the Flow Control Settings & click "OK"
6. Pay attention, because for a brief mmoment MTTY wil report whether or not it could establish a port connection to USB. If you are successful, a Command window will open.
7. Hit the "Enter" key on your PC twice. You should then see a command prompt that looks like this "cmd>".
8. At the command prompt (cmd>) you should enter the command "boot".
This will reboot the device & report back about any errors or bad or erased blocks.
9. If your device was just hung, it should be fine after the reboot. If it returns to Boot Loader however, it means there was a problem with bad blocks.
10. If errors were reported & you end up back at the Boot Loader screen, then repeat the "Boot" Comand at the (cmd>) prompt.

It can sometimes take two or three boots to fully recover from RUUNBH errors, so if at first you don't succeed keep trying & remember to keep notes about any errors reported in the MTTY info window.

Other Information: MTTY needs to have full access to the USB port. Some anti-spyware, anti-virus & firewall programs can prevent MTTY from gaining the port access it needs. McCaffee in particular should be temporarily disabled & some firewall programs may also need to be disabled.

This method ****ed-up my HTC HD2 T-Mobile. My phone does not power on anymore. Can not even go to Hard Reboot (Button down + reset button), even can not do (up an down button + power button) Nothing working now. I removed the battery for 48 Hours and tried again. Nothing Working. Thank you for destroying my phone

thanks
its working 100%

Utizando el MTTY

---

Originally Posted by Laurentius26

Thanks for confirmation!

Yo tengo un Kaiser 120 en la pantalla de arranque me aparece
RUUNBH en la ángulo superior derecho
KAIS120
SPL-1.93
CPLD-8

Con el MTTY

Cmd>set 14 0
HTCST ÚÈÒHTCE
Cmd>task 28
Format start
Storage start sector=0x8E40, total sector=0x12480
Storage start block=590, total block=1170
Total Bad Block in CE: 0
Erase physical block from 880 to 2032
si backup: Erase physical block from 2032 to 2048
Format end
Cmd>task 0
Cmd>
no se reinicia el SO, lo intento manualmente y nada. Alguna Sugerencia

Thank you all!!!

---

Thank you very much guys, I was stuck in bootloader with the "Loading..." sign on it...

I was able to identify correctly my phone with MTTY, command "set 14 0", I gets me back "VODA P...", downloaded stock rom from Vodafone UK, flashed it and then I Updated my Hard SPL...

Now running lots of Android roms and everything fine!!!

Thank you again, You are doing a really good job!!!

Thank you very much!!

When I found the article which can change the TyTN II to Andriod, I follow the step of Hard SPL (I copy the file JumpSPL1.56-KAIS.exe to the phone and run it, and then run the KaiserCustomRUU.exe in PC, the process is fail in 99%. In this time, I believe that I lose my phone. Fortunely found this thread.