[2/24 v1.5 NEW] nueLED - configure LEDS on any HTC device

---

Hello,

I have designed a intermediate LED driver that sits between the led driver and decides which calls to pass through and whether to redirect them or not.

NEW VERSION 1.5 with sleep. Fixes registry release issue.



Basically, you can now turn off your signal light, make it flash blue instead of green, or whatever you wish. So far it's been tested on the titan and the kaiser, but should work on any device that uses ALLLEDMGR. nueLED renames allledmgr to LED2: and names itself LED1:. Please let me know if it works/doesn't work on your device.

Settings are stored in the registry, -1 means active and -2 means inactive, any other number is a redirect. To figure out new addresses, use diagnostic mode in settings.

Heres a short tutorial on how to make your signal LED flash blue:
Select the signal led from the list. It has address 8, mode 1.
Select the option "Redirect to LED Address", and select bluetooth LED.
Soft-Reset your device.

Your signal LED should now be blue!

If you use the cab version and decide to remove it, you need to set
[HKEY_LOCAL_MACHINE\Drivers\BuiltIn\AllLEDMgr]
"Index"=dword:1

and perorm a soft reset to re-enable the old led driver. Also delete the [HKEY_LOCAL_MACHINE\Drivers\BuiltIn\nueLED] key.

You can find nueLED at http://www.weienterprises.com/nue
Stroths has provided a cab version for your convenience.

A program to help you control your leds, nueLEDControl is also included. The syntax is relatively simple, i.e. nueLEDControl "address" "mode".

If you appreciate nueLED, donations are welcome. Comments, bug reports, etc. are also welcome.

What a unique soft hehe will try it soon and give feedback

this is fantastic!
i have it installed on my HTC Touch, seems to work fabulous.
when its charging however, i tried to change it to the blue led, but it did not go to it...might be a small bug?

Originally Posted by korea206

this is fantastic!
i have it installed on my HTC Touch, seems to work fabulous.
when its charging however, i tried to change it to the blue led, but it did not go to it...might be a small bug?

hmmm ... did you set 34 to redirect to 32? ... It will only cause the blue led to flash, not stay lit.

Also, diagnostic mode is not working in v1.1, I am updating that right now, 1.2 will fix the problem.

Very original, nice job.

I tried this on a magician and now, even after uninstall, all my leds are dead, is ther a registry key I must delete?
Thank you for a great piece of software, too bad it doesnt work on my model...

---
Nevermind, I deleted the nueLED entry on the registry, reseted and its all working again.
Is there any way of dicovering the number of the led colors in a magician? the settings check area doesnt do anything for me...

---edit---

Originally Posted by twolf

Thats strange, his site changed and no nueled inside...
Here are some mirrors:

Atachment: http://forum.xda-developers.com/atta...5&d=1220599385

Download mirror(37kb): http://rapidshare.de/files/40111294/...D_1.5.zip.html

Originally Posted by twolf

I tried this on a magician and now, even after uninstall, all my leds are dead, is ther a registry key I must delete?
Thank you for a great piece of software, too bad it doesnt work on my model...

sorry about your leds, you just need to set the registry setting
[HKEY_LOCAL_MACHINE\Drivers\BuiltIn\AllLEDMgr]
"Index"=dword:1

If you could post allledmgr.dll for your device, perhaps i can make it compatible =)

It setted itself back on, I edited my previous post as you were writing this one, hehehe...

Again, great software, and I havent given up to make it work in my magician... So, is there any way of dicovering the number of the led colors in a magician? the settings check area doesnt do anything for me...

Originally Posted by twolf

It setted itself back on, I edited my previous post as you were writing this one, hehehe...

Again, great software, and I havent given up to make it work in my magician... So, is there any way of dicovering the number of the led colors in a magician? the settings check area doesnt do anything for me...

yes, there is a way, however a bug is preventing the diagnostic mode from working - 1.2 will fix that... should be released real soon.

Great news, thanks!!!