HELP - hx2110 dead after upgrading to WM6.1

---

I download the WM6.1 from following link:-

http://forum.xda-developers.com/showthread.php?t=383173

but my unit was dead after flashing the ROM.

- the unit can turn on but never ending on the startup screen.
- the unit can enter BootLoader but the computer can't recognise it, so i can't re-flash it any more.

I have tried to uninstall the ActiveSync and re-install it but helpless.

Can anyone help?
Thanks.

No Panic

---

Originally Posted by tangwd898

I download the WM6.1 from following link:-

http://forum.xda-developers.com/showthread.php?t=383173

but my unit was dead after flashing the ROM.

- the unit can turn on but never ending on the startup screen.
- the unit can enter BootLoader but the computer can't recognise it, so i can't re-flash it any more.

I have tried to uninstall the ActiveSync and re-install it but helpless.

Can anyone help?
Thanks.

Many people experienced identical problems with hx2110/2115/2410/2415, wm2003se, having 64MB Rom, when try to upgrading wm6.0/wm6.1

Come here, no Panic......
http://forum.xda-developers.com/show...383173&page=36 info in post #353

You must read carefully to understand the guides in further Threads introduced, and proceed with patience...

Sure you'll make it.....Like me....hx2110 to any wm6.1

HKKSL, YOUR ADVISE IS REALLY HELP,THANK YOU VERY MUCH.

Upgrading HX2110 to WM6

--------------------------------------------------------------------------------

Okay, I've finally got WM6 on my HX2110. For any other people having the same problems I did, here is exactly what I did. What the guides I've found don't tell you is where to find it, and what to do when you get it. Basically you need to trick the iPaq into thinking it's getting the original 1.00.00.l firmware and then switch firmwares. You need to downgrade to the original H firmware before the iPaq will accept wm6. This worked perfectly for me after two days of trial and error. More detailed steps are below, but basically its: flash with 100l, reset, run 100l and swap firmware with 100h, flash, run 100l and swap with wm6, flash

Prerequisites:
Advanced_pack_for_hx2xxx_to_WM6
iPaq HX2110
USB connection to computer

1) Hard reset iPaq. Do this by holding the calendar button and itask button (curved arrow), and then put your stylus into the reset hole on the bottom of the iPaq. This will hard reset it.
2) After doing that, put it in to bootloader mode. You do this by holding the contact button (to the right of the calendar) and the itask arrow, and then clicking the reset button on the bottom. It should now be in bootloader mode. unplug the power/usb cable and plug it back in. hit the calendar button. it should now say USB.
3) run hpRUU.exe under the Wm5.0 for hx2000_1.00.00.L_ENG folder. It's found in provishki. it will flash your ipaq to 1.00.00.l . let it flash all the way.
4) hard reset the ipaq and put it in bootloader mode. see steps 1 and 2. make sure it says USB.
5) do step 3 again, but this time don't click upgrade. rename the E1_Upgrade_ROM_v1_00_00_L_SIGNED.nbf file to 100l.nbf
6) go into the SP32408_1.00.00.H_ENG folder and get the NBF file from there. copy it into the 1.00.00.L folder that we were just in. rename is to E1_Upgrade_ROM_v1_00_00_L_SIGNED.nbf. click upgrade. let the upgrade finish.
7) repeat steps 1 and 2.
8) delete the E1_Upgrade_ROM_v1_00_00_L_SIGNED.nbf file that you just copied over and rename the 100l.nbf file to E1_Upgrade_ROM_v1_00_00_L_SIGNED.nbf.
9) run hpruu.exe again. DO NOT CLICK UPGRADE.
10) get the wm6_wwe.nbf file and copy it into the directory we were just in. rename E1_Upgrade_ROM_v1_00_00_L_SIGNED.nbf to 100l.old and wm6_wwe.nbf to E1_Upgrade_ROM_v1_00_00_L_SIGNED.nbf
11) click upgrade. let it finish.
12) repeat step 1

you should now have Windows Mobile 6 on your iPaq. Good luck

--------------------------------------------------------------------------------
Last edited by jsbarone : 29-02-2008 at 05:06 AM.

Complete package for upgrade hx2xxx to WM6

--------------------------------------------------------------------------------

Inside:
-WWE-hx2000_PPC03_downgrade for return to WM2003se
-Wm5.0 for hx2000_1.00.00.L_ENG
-Wm5.0 for hx2750_1.00.00.L_ENG
-SP32205_1.00.03.H_RUS
-SP32205_1.00.03.H_RUS
-SP32408_1.00.00.H_ENG
-SP33003_1.02.00.H_ENG
-WM6.0_5.20.00.H_ENG
-Terminal_RDP
-Quarta
-hx2x90b_Mui_Quarta7

http://depositfiles.com/en/files/1799963

I have succeed in upgrading my hx2110 to wm6.1 as per the above instruction.

I am wondering why there's extra files and folders in that package that we never used it?