[android] Problem with NAND :/

---

Hello!
Ive got a problem aftter flashing a *.nbh for NAND android :/ It just hanged on the splash screen. No any linux logs

If you can still get bootloader, try reflashing, sometimes it fails for no apparent reason, if that still does not work, try formatting the SD, recopy the nbh, reflash again.

If all else fails, you may be one of those who cannot flash to nand, I have 2 kais130's one flashes every time, the other, about 1 in 15 times is successful.

Originally Posted by zenity

If you can still get bootloader, try reflashing, sometimes it fails for no apparent reason, if that still does not work, try formatting the SD, recopy the nbh, reflash again.

If all else fails, you may be one of those who cannot flash to nand, I have 2 kais130's one flashes every time, the other, about 1 in 15 times is successful.

I can still get bootloader, a reflashed, today i putted new SDHC card and i try to reflash nbh. Only 1 time after flash I can see linux logs, I can to install it too, but when ill reboot phone then hangs like early :/

Ok first which Android build are you trying?
When you say reboot, are you using the reset button or pulling the battery after flashing, ( using reset can cause problems, the correct method is flash, pull battery, wait, replace battery ).

Which nbh are you trying to flash? If you had android working then you may want to go back to the nbh you used before.

Originally Posted by zenity

Ok first which Android build are you trying?
When you say reboot, are you using the reset button or pulling the battery after flashing, ( using reset can cause problems, the correct method is flash, pull battery, wait, replace battery ).

Which nbh are you trying to flash? If you had android working then you may want to go back to the nbh you used before.

Im using kaisimg-panel1-428-12-03-10, im using a reset button not battery trick. Im using warm donut biuld. As I said i can boot android from NAND just 1 time, not anymore

Well the best nbh's for the kaiser are still the sourceforge ones at least for stability, the 20/02/2010 ones, yes there are newer ones, but they may require some pretty advanced editing of some system files before they run properly, and may not be fully compatible with the donut build.

I think it may be better to use one of these : http://sourceforge.net/projects/andr.../kaisereclair/

I have the same issue with dzos latest. I posted it in the bluetooth thread as to not open any unneeded topics. The fix he posted 11-03-10 for bluetooth booted fine, this one gives me the same issue. Remember this stuff is all relatively experimental so try not to panic when using the very latest since it might not work.

Apparently there is a problem with the latest nbh's, I'd just reflash an earlier NBH, this should fix the problem.

I'm having the exact same problem. Everything seems to get installed properly but once I take out the battery to reboot it just hangs on the splash screen. I've tried several builds and reformatted the card several times... always the same result. In one of the posts I cam across it was mentioned that you first have to go in to win mobile to turn off a pin # and that can cause the system to hang if not done. I can't find the post anymore and I'm not sure what they were talking about.

Originally Posted by kcbronc

I'm having the exact same problem. Everything seems to get installed properly but once I take out the battery to reboot it just hangs on the splash screen. I've tried several builds and reformatted the card several times... always the same result. In one of the posts I cam across it was mentioned that you first have to go in to win mobile to turn off a pin # and that can cause the system to hang if not done. I can't find the post anymore and I'm not sure what they were talking about.

Yeah I read about disabling the pin thing in Win Mo as well, but unfortunately this was after I flashed Android to NAND. Mine hangs at the splash screen as well, but if you put the KAISDIAG.nbh file in the root of your SD card, from the Hard SPL threads, the phone will boot and get to the Android installer, but will then come up with errors when choosing to install to NAND. Unfortunately, I can't even go back to Win Mo because of this.