FORUMS

[HOWTO] Linux on Xiaomi Mi Box S(MDZ-22-AB)

11 posts
Thanks Meter: 5
 
By recrof, Junior Member on 30th December 2018, 05:58 PM
Post Reply Email Thread
25th February 2019, 05:51 AM |#11  
Junior Member
Thanks Meter: 0
 
More
Quote:
Originally Posted by recrof

Your board is not mdz-22-ab, so I can't help you with that. I have tried lots of contact points before I discovered right ones. Don't be affraid to experiment, you will find correct pins eventually.

yes this board 3s, my board https://gadgetpage.ru/razbiraem-i-iz...-mi-box-s.html
Do not burn the board while experimenting?
5th March 2019, 10:11 AM |#12  
OP Junior Member
Thanks Meter: 5
 
More
Quote:
Originally Posted by elitecop

yes this board 3s, my board https://gadgetpage.ru/razbiraem-i-iz...-mi-box-s.html
Do not burn the board while experimenting?

There is always risk of burning the board, but it's very low.
17th March 2019, 11:56 PM |#13  
Junior Member
Thanks Meter: 0
 
More
error during boting
the box does not start!
I connected the box via serial usb, and this is the log:

GXL:BL1:9ac50e:bb16dc;FEAT:BDFD71BC:0;POC:3;RCY:0; EMMC:0;READ:0;0.0;0.0;CHK:0;
TE: 90559

BL2 Built : 13:27:37, Oct 25 2017. gxl g56b77aa - [email protected]

_vcc5_power_init
rn5t567_power_init
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
Board ID = 5
CPU clk: 1200MHz
DQS-corr enabled
DDR scramble enabled
DDR3 chl: Rank0+1 @ 912MHz - FAIL
DDR3 chl: Rank0 @ 912MHz - FAIL
DDR3 chl: Rank0 16bit @ 912MHz - FAIL
DDR4 chl: Rank0+1 @ 1008MHz - FAIL
DDR4 chl: Rank0 @ 1008MHz - FAIL
DDR4 chl: Rank0 16bit @ 1008MHz - FAIL
DDR init failed...
Reset...

-------------------------------------------------------------------------------------

Can you give me some advice?
26th March 2019, 05:31 AM |#14  
Junior Member
Thanks Meter: 0
 
More
Could this apply for mi box 4 mdz-21-aa?
27th June 2019, 09:49 AM |#15  
Senior Member
Thanks Meter: 46
 
More
Anyone found a way for root on latest android tv?
27th June 2019, 09:19 PM |#16  
Junior Member
Thanks Meter: 0
 
More
I connected the mibox 4c with cp2012 at windows 10
Hi, dear friend
I connected the mibox 4c with cp2012 at windows 10
, After I start the box and press ctl+c or space. Can not stop the uboot.i checked .
I checked the tx and Rx connection. It is OK.
How to fix it?
Maybe the xiaomi change something of uboot and disable the interruption ?

---------- Post added at 08:19 PM ---------- Previous post was at 08:03 PM ----------

This is my video of connection.
Please search andy漫漫说 at YouTube to get my channel and find the latest video.
I am newbie here. Can not post link .
Somebody help me ?



Code:
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2019.06.28 05:39:49 =~=~=~=~=~=~=~=~=~=~=~=
GXL:BL1:9ac50e:bb16dc;FEAT:ADFC718C:0;POC:3;RCY:0;EMMC:0;READ:0;0.0;CHK:0;
TE: 224076

BL2 Built : 18:13:36, Jun 17 2016. 
gxl g176ecdb - [email protected]

set vcck to 1120 mv
set vddee to 1000 mv
Board ID = 1
CPU clk: 1200MHz
DDR3 chl: Rank0+1 @ 792MHz - FAIL
DDR3 chl: Rank0 @ 792MHz - PASS
DQS-corr enabled
DDR scramble enabled
Rank0: 1024MB(auto)-2T-11
DataBus test pass!
AddrBus test pass!
-s
Load fip header from eMMC, src: 0x0000c200, des: 0x01400000, size: 0x00004000
New fip structure!
Load bl30 from eMMC, src: 0x00010200, des: 0x01100000, size: 0x0000d600
Load bl31 from eMMC, src: 0x00020200, des: 0x10100000, size: 0x00014400
Load bl33 from eMMC, src: 0x00038200, des: 0x01000000, size: 0x000cc400
NOTICE:  BL3-1: v1.0(debug):ed1aadc
NOTICE:  BL3-1: Built : 11:06:24, May 31 2016
aml log : bl31 normal boot !
[Image: gxl_v1.1.3122-bcd5b77 2018-07-11 18:46:53 [email protected]]

OPS=0xc4

0 0 3 c c 0 d1 b3 40 a0 0 c4 [0.594431 Inits done]

secure task start!
high task start!
low task start!
INFO:    BL3-1: Initializing runtime services
WARNING: No OPTEE provided by BL2 boot loader
ERROR:   Error initializing runtime service opteed_fast
INFO:    BL3-1: Preparing for EL3 exit to normal world
INFO:    BL3-1: Next image address = 0x1000000
INFO:    BL3-1: Next image spsr = 0x3c9


U-Boot 2015.01-gfbef5dd (Sep 25 2018 - 15:03:01), Build: jenkins-transformers-627

DRAM:  1 GiB
Relocation Offset is: 36ea8000
gpio: pin gpiox_6 (gpio 6) value is 1
gpio: pin gpioao_4 (gpio 123) value is 1
register usb cfg[0][1] = 0000000037f64488
vpu: error: vpu: check dts: FDT_ERR_BADMAGIC, load default parameters
vpu: clk_level = 7
vpu: set clk: 666667000Hz, readback: 666660000Hz(0x300)
saradc_enable1 P_SAR_ADC_REG13: 0x0
saradc: check dts: FDT_ERR_BADMAGIC, load default parameters
saradc_enable2 P_SAR_ADC_REG13: 0x1100
MMC:   aml_priv->desc_buf = 0x0000000033ea8f50
aml_priv->desc_buf = 0x0000000033eaaf60
SDIO Port B: 0, SDIO Port C: 1
emmc/sd response timeout, cmd8, status=0x3ff2800
emmc/sd response timeout, cmd55, status=0x3ff2800
[mmc_init] mmc init success
mmc read lba=0x4000, blocks=0x400
      Amlogic multi-dtb tool
      Multi dtb detected
saradc: check dts: FDT_ERR_BADMAGIC, load default parameters
get_adc_value ch(1) 79
aml_dt=gxl_tf_1g
      Multi dtb tool version: v2 .
      Support 2 dtbs.
        aml_dt soc: gxl platform: tf variant: 1g
        dtb 0 soc: gxl   plat: tf   vari: 1g
        dtb 1 soc: gxl   plat: tf   vari: 2g
      Find match dtb: 0
start dts,buffer=0000000033ead670,dt_addr=0000000033eade70
parts: 13
00:     cache	0000000010000000 2
01:      logo	0000000000300000 1
02:   encrypt	0000000000100000 1
03:  recovery	0000000002000000 1
04:       tee	0000000000800000 1
05:     crypt	0000000002000000 1
06:      misc	0000000002000000 1
07:      boot	0000000001400000 1
08:    system	0000000040000000 1
09:    backup	0000000020000000 4
10:   persist	0000000000800000 4
11:     panic	0000000000400000 4
12:      data	ffffffffffffffff 4
get_dtb_struct: Get emmc dtb OK!
overide_emmc_partition_table: overide cache 
[mmc_get_partition_table] skip partition cache.
Partition table get from SPL is : 
        name                        offset              size              flag
===================================================================================
   0: bootloader                         0            400000                  0
   1: reserved                      400000            800000                  0
   2: cache                         c00000          10000000                  2
   3: env                         10c00000            400000                  0
   4: logo                        11000000            300000                  1
   5: encrypt                     11300000            100000                  1
   6: recovery                    11400000           2000000                  1
   7: tee                         13400000            800000                  1
   8: crypt                       13c00000           2000000                  1
   9: misc                        15c00000           2000000                  1
  10: boot                        17c00000           1400000                  1
  11: system                      19000000    @     40000000                  1
  12: backup                      59000000          20000000                  4
  13: persist                     79000000            800000                  4
  14: panic                       79800000            400000                  4
  15: data                        79c00000         158400000                  4
mmc read lba=0x2000, blocks=0x2
mmc read lba=0x2002, blocks=0x2
mmc_read_partition_tbl: mmc read partition OK!
eMMC/TSD partition table have been checked OK!
mmc env offset: 0x10c00000 
In:    serial
Out:   serial
Err:   serial
reboot_mode=cold_boot
hardware_version=1
hpd_state=1
[1080p60hz] is invalid for cvbs.
set hdmitx VIC = 16
config HPLL = 3000
HPLL: 0xc000027b
config HPLL done
j = 4  vid_clk_div = 1
hdmitx phy setting done
hdmitx: set enc for VIC: 16
enc_vpu_bridge_reset[1183]
rx version is 1.4 or below  div=10
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
read emmc dtb
      Amlogic multi-dtb tool
      Multi dtb detected
aml_dt=gxl_tf_1g
      Multi dtb tool version: v2 .
      Support 2 dtbs.
        aml_dt soc: gxl platform: tf variant: 1g
        dtb 0 soc: gxl   plat: tf   vari: 1g
        dtb 1 soc: gxl   plat: tf   vari: 2g
      Find match dtb: 0
P_SAR_ADC_REG13: 0x1000
P_SAR_ADC_REG13  bak: 0x10
P_SAR_ADC_REG13: 0x1000
SEC_AO_SEC_SD_CFG12: 0xa040b3d1
ffu update start
old fw_ver = 6
amlkey_init() enter!
[EFUSE_MSG]keynum is 4
wipe_data=successful
wipe_cache=successful
Boot command: 
Boot status: 
Boot message
""
upgrade_step=2
[OSD]load fb addr from dts
[OSD]failed to get fb addr for logo
[OSD]use default fb_addr parameters
[OSD]fb_addr for logo: 0x3d800000
[OSD]load fb addr from dts
[OSD]failed to get fb addr for logo
[OSD]use default fb_addr parameters
[OSD]fb_addr for logo: 0x3d800000
[CANVAS]canvas init
[CANVAS]addr=0x3d800000 width=5760, height=2160
pull down bt_reset
pull up bt_reset
set hci reset
bt_vendor_name = Realteck RTL8723DS 
set scan parameters
set scan enable
pull down bt_enable
IR init done!
ee_gate_off ...
## Booting Android Image at 0x01080000 ...
reloc_addr =33f2d890
copy done
      Amlogic multi-dtb tool
      Single dtb detected
load dtb from 0x1000000 ......
   Uncompressing Kernel Image ... OK
   kernel loaded at 0x01080000, end = 0x02043d58
   Loading Ramdisk to 33ded000, end 33e95658 ... OK
   Loading Device Tree to 000000001fff4000, end 000000001ffffcda ... OK

Starting kernel ...

uboot time: 2655518 us
[    [email protected]] Initializing cgroup subsys cpuset
[    [email protected]] Initializing cgroup subsys cpu
[    [email protected]] Initializing cgroup subsys cpuacct
[    [email protected]] Linux version 3.14.29-301482-g2d0e095 ([email protected]) (gcc version 4.9.2 20140904 (prerelease) (crosstool-NG linaro-1.13.1-4.9-2014.09 - Linaro GCC 4.9-2014.09) ) #1 SMP PREEMPT Tue Sep 25 14:57:56 CST 2018
[    [email protected]] CPU: AArch64 Processor [410fd034] revision 4
[    [email protected]] no prop version_code
[    [email protected]] bootconsole [earlycon0] enabled
[    [email protected]] fdt Reserved memory table:
[    [email protected]]            linux,meson-fb: 0x000000003e000000 - 0x0000000040000000  (32 MiB)
[    [email protected]]                  linux,di: 0x000000003c200000 - 0x000000003e000000  (30 MiB)
[    [email protected]] DI: DI reserved memory: created CMA memory pool at 0x000000003c200000, size 30 MiB
[    [email protected]]             linux,ion-dev: 0x0000000039200000 - 0x000000003c200000  (48 MiB)
[    [email protected]]               linux,ppmgr: 0x0000000039200000 - 0x0000000039200000  (0 MiB)
[    [email protected]]        linux,codec_mm_cma: 0x0000000027c00000 - 0x0000000033c00000  (192 MiB)
[    [email protected]]              linux,picdec: 0x0000000039200000 - 0x0000000039200000  (0 MiB)
[    [email protected]] Reserved memory: incorrect alignment of CMA region
[    [email protected]]   linux,codec_mm_reserved: 0x0000000035100000 - 0x0000000039200000  (65 MiB)
[    [email protected]] fdt Reserved memory total:  370 MiB
[    [email protected]] psci: probing function IDs from device-tree
[    [email protected]] PERCPU: Embedded 12 pages/cpu @ffffffc0350a8000 s20224 r8192 d20736 u49152
[    [email protected]] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 257539
[    [email protected]] Kernel command line: rootfstype=ramfs init=/init console=ttyS0,115200 no_console_suspend earlyprintk=aml-uart,0xc81004c0 ramoops.pstore_en=1 ramoops.record_size=0x8000 ramoops.console_size=0x4000 logo=osd1,loaded,0x3d800000,1080p60hz hdmimode=1080p60hz cvbsmode=576cvbs hdmitx= vout=1080p60hz,enable cvbsdrv=0 boardver= jtag=apao androidboot.hardware=amlogic androidboot.firstboot=0 androidboot.btmac=00:00:00:00:00:00 androidboot.wifimac=c8:28:32:b7:c3:0e androidboot.wificountrycode=CN androidboot.serialno=17132/280733558 androidboot.selinux=enforcing androidboot.recoveryflag=false androidboot.hardware_version=1 androidboot.bootreason=cold_boot 
[    [email protected]] logo: osd1
[    [email protected]] logo: loaded
[    [email protected]] logo: 0x3d800000
[    [email protected]] logo: 1080p60hz
[    [email protected]] logo: get hdmimode: 1080p60hz
[    [email protected]] logo: get cvbsmode: 576cvbs
[    [email protected]] vout_serve: 1080p60hz
[    [email protected]] vout_serve: enable: 1
[    [email protected]] tv_vout: cvbs performance line = 0
[    [email protected]] jtag: jtag select 2
[    [email protected]] (NULL device *): [mac_addr_set] try to wifi mac from emmc key!
[    [email protected]] (NULL device *): [mac_addr_set] uboot setup mac-addr: c8:28:32:b7:c3:e
[    [email protected]] PID hash table entries: 4096 (order: 3, 32768 bytes)
[    [email protected]] Dentry cache hash table entries: 131072 (order: 8, 1048576 bytes)
[    [email protected]] Inode-cache hash table entries: 65536 (order: 7, 524288 bytes)
[    [email protected]] Memory: 621540K/1044480K available (9852K kernel code, 1111K rwdata, 3956K rodata, 1216K init, 5803K bss, 422940K reserved)
[    [email protected]] Virtual kernel memory layout:
[    [email protected]]     vmalloc : 0xffffff8000000000 - 0xffffff807fff0000   (  2047 MB)
[    [email protected]]     vmemmap : 0xffffff8080000000 - 0xffffff8080e00000   (    14 MB)
[    [email protected]]     modules : 0xffffffbffc000000 - 0xffffffc000000000   (    64 MB)
[    [email protected]]     memory  : 0xffffffc000000000 - 0xffffffc040000000   (  1024 MB)
[    [email protected]]       .init : 0xffffffc001dfe000 - 0xffffffc001f2e000   (  1216 kB)
[    [email protected]]       .text : 0xffffffc001080000 - 0xffffffc001dfd334   ( 13813 kB)
[    [email protected]]       .data : 0xffffffc001f2e000 - 0xffffffc002043d58   (  1112 kB)
[    [email protected]] PM: Registered nosave memory: [mem 0x01080000-0x01dfcfff]
[    [email protected]] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    [email protected]] arch_multi_cluster:0
[    [email protected]] Preemptible hierarchical RCU implementation.
[    [email protected]] 	RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
[    [email protected]] RCU: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[    [email protected]] NR_IRQS:64 nr_irqs:64 0
[    [email protected]] Architected cp15 timer(s) running at 24.00MHz (phys).
[    [email protected]] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 2863311519744ns
[    [email protected]] meson_bc_timer: mclk->mux_reg =ffffff800000c990,mclk->reg =ffffff800000e994
[    [email protected]] Console: colour dummy device 80x25
[    [email protected]] allocated 4194304 bytes of page_cgroup
[    [email protected]] please try 'cgroup_disable=memory' option if you don't want memory cgroups
[    [email protected]] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=240000)
[    [email protected]] pid_max: default: 32768 minimum: 301
[    [email protected]] Security Framework initialized
[    [email protected]] SELinux:  Initializing.
[    [email protected]] Mount-cache hash table entries: 2048 (order: 2, 16384 bytes)
[    [email protected]] Mountpoint-cache hash table entries: 2048 (order: 2, 16384 bytes)
[    [email protected]] device-tree: Duplicate name in /efusekey, renamed to "key0#1"
[    [email protected]] device-tree: Duplicate name in /efusekey, renamed to "key1#1"
[    [email protected]] device-tree: Duplicate name in /efusekey, renamed to "key2#1"
[    [email protected]] device-tree: Duplicate name in /efusekey, renamed to "key3#1"
[    [email protected]] Initializing cgroup subsys debug
[    [email protected]] Initializing cgroup subsys memory
[    [email protected]] Initializing cgroup subsys freezer
[    [email protected]] Initializing cgroup subsys blkio
[    [email protected]] ftrace: allocating 33470 entries in 131 pages
[    [email protected]] /cpus/[email protected]: Missing clock-frequency property
[    [email protected]] /cpus/[email protected]: Missing clock-frequency property
[    [email protected]] /cpus/[email protected]: Missing clock-frequency property
[    [email protected]] /cpus/[email protected]: Missing clock-frequency property
[    [email protected]] hw perfevents: enabled with arm/armv8-pmuv3 PMU driver, 7 counters available
[    [email protected]] ftrace: Allocated trace_printk buffers
[    [email protected]] Meson chip version = RevC (21:C - C4:0)
[    [email protected]] CPU1: Booted secondary processor
[    [email protected]] CPU2: Booted secondary processor
[    [email protected]] CPU3: Booted secondary processor
[    [email protected]] Brought up 4 CPUs
[    [email protected]] SMP: Total of 4 processors activated.
[    [email protected]] sched: registering cpufreq notifiers for scale-invariant loads
[    [email protected]] instabooting: 0
[    [email protected]] pinctrl core: initialized pinctrl subsystem
[    [email protected]] regulator-dummy: no parameters
[    [email protected]] NET: Registered protocol family 16
[    [email protected]] ramoops: using module parameters
[    [email protected]] console [pstore-1] enabled
[    [email protected]] pstore: Registered ramoops as persistent store backend
[    [email protected]] ramoops: attached [email protected], ecc: 0/0
[    [email protected]] cpuidle: using governor menu
[    [email protected]] aml_vdac_init: module init
[    [email protected]] register canvas platform driver
[    [email protected]] register rdma platform driver
[    [email protected]] vdso: 2 pages (1 code, 1 data) at base ffffffc001f38000
[    [email protected]] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[    [email protected]] DMA: preallocated 256 KiB pool for atomic allocations
[    [email protected]] software IO TLB [mem 0x26000000-0x26040000] (0MB) mapped at [ffffffc026000000-ffffffc02603ffff]
[    [email protected]] Serial: AMBA PL011 UART driver
[    [email protected]] aml_i2c version: 20140813
[    [email protected]] i2c-core: driver [pmu4] using legacy resume method
[    [email protected]] codec_mm:codec_mm_module_init
[    [email protected]] aml_watch_point_probe, in
[    [email protected]] gxbb_mpll_clk: register mpll_clk_out0 success done
[    [email protected]] gxbb_mpll_clk: register mpll_clk_out1 success done
[    [email protected]] gxbb_mpll_clk: register mpll_clk_out2 success done
[    [email protected]] clk_sys: register PLL sys_pll success done
[    [email protected]] gxl_clk: [ xtal 	] ->clockrate: 24000000Hz
[    [email protected]] gxl_clk: [ 32Khz 	] ->clockrate: 32000Hz
[    [email protected]] gxl_clk: [ clk81 	] ->clockrate: 166666666Hz
[    [email protected]] gxl_clk: [ fixed_pll 	] ->clockrate: 2000000000Hz
[    [email protected]] gxl_clk: [ fclk_div2 	] ->clockrate: 1000000000Hz
[    [email protected]] gxl_clk: [ fclk_div3 	] ->clockrate: 666666666Hz
[    [email protected]] gxl_clk: [ fclk_div4 	] ->clockrate: 500000000Hz
[    [email protected]] gxl_clk: [ fclk_div5 	] ->clockrate: 400000000Hz
[    [email protected]] gxl_clk: [ fclk_div7 	] ->clockrate: 285714285Hz
[    [email protected]] gxl_clk: clock initialization complete
[    [email protected]] clkmsr: Gxl msr_clk_reg0=ffffff800003a75c,msr_clk_reg2=ffffff800003c764
[    [email protected]] aml_iomap: amlogic iomap probe done
[    [email protected]] pinmux-gxl c1109880.pinmux: Init pinux probe!
[    [email protected]] pinmux-gxl c1109880.pinmux: Probed amlogic pinctrl driver
[    [email protected]] genirq: Setting trigger mode 8 for irq 241 failed (gic_set_type+0x0/0xbc)
[    [email protected]] genirq: Setting trigger mode 8 for irq 242 failed (gic_set_type+0x0/0xbc)
[    [email protected]] genirq: Setting trigger mode 8 for irq 241 failed (gic_set_type+0x0/0xbc)
[    [email protected]] genirq: Setting trigger mode 8 for irq 242 failed (gic_set_type+0x0/0xbc)
[    [email protected]] codec_mm has 2 memory regions
[    [email protected]] codec_mm codec_mm.18: assigned reserved memory node linux,codec_mm_cma ok
[    [email protected]] codec_mm codec_mm.18: assigned reserved memory node linux,codec_mm_reserved ok
[    [email protected]] codec_mm has 2 memory regions
[    [email protected]] codec_mm codec_mm.18: assigned reserved memory node linux,codec_mm_cma ok
[    [email protected]] codec_mm codec_mm.18: assigned reserved memory node linux,codec_mm_reserved ok
[    [email protected]] vpu: driver version: v02
[    [email protected]] vpu: load vpu_clk: 666667000Hz(7)
[    [email protected]] vpu: vpu_probe OK
[    [email protected]] tv_vout: tvout_probe
[    [email protected]] tv_vout: major number 254 for disp
[    [email protected]] vout_notify: vout_register_server
[    [email protected]] tv_vout: register tv module server ok
[    [email protected]] tv_vout: tvout_probe OK
[    [email protected]] canvas_probe reg=00000000c8838000,size=400
[    [email protected]] canvas maped reg_base =ffffff800008e000
[    [email protected]] rdma_probe
[    [email protected]] bio: create slab <bio-0> at 0
[    [email protected]] SCSI subsystem initialized
[    [email protected]] usbcore: registered new interface driver usbfs
[    [email protected]] usbcore: registered new interface driver hub
[    [email protected]] usbcore: registered new device driver usb
[    [email protected]] i2c-gpio i2c_gpio.35: using pins 172 (SDA) and 173 (SCL)
[    [email protected]] Linux video capture interface: v2.00
[    [email protected]] pps_core: LinuxPPS API ver. 1 registered
[    [email protected]] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <[email protected]>
[    [email protected]] PTP clock support registered
[    [email protected]] hdmitx: system: amhdmitx_init
[    [email protected]] hdmitx: system: Ver: 2014May6
[    [email protected]] hdmitx: system: amhdmitx_probe
[    [email protected]] ------------[ cut here ]------------
[    [email protected]] WARNING: CPU: 0 PID: 1 at /home/work/data/jenkins/workspace/transformers/common/drivers/base/core.c:549 device_create_file+0xa4/0xbc()
[    [email protected]] Attribute product_name: write permission without 'store'
[    [email protected]] Modules linked in:
[    [email protected]] CPU: 0 PID: 1 Comm: swapper/0 Not tainted 3.14.29-301482-g2d0e095 #1
[    [email protected]] Call trace:
[    [email protected]] [<ffffffc0010894d8>] dump_backtrace+0x0/0x144
[    [email protected]] [<ffffffc001089638>] show_stack+0x1c/0x28
[    [email protected]] [<ffffffc001a0b108>] dump_stack+0x74/0xb8
[    [email protected]] [<ffffffc0010a0088>] warn_slowpath_common+0x98/0xc0
[    [email protected]] [<ffffffc0010a0124>] warn_slowpath_fmt+0x74/0x88
[    [email protected]] [<ffffffc001454cd4>] device_create_file+0xa0/0xbc
[    [email protected]] [<ffffffc00163fa14>] amhdmitx_probe+0x2ac/0x924
[    [email protected]] [<ffffffc00145bc68>] platform_drv_probe+0x28/0x60
[    [email protected]] [<ffffffc001459bd4>] really_probe+0xd4/0x244
[    [email protected]] [<ffffffc001459e68>] __driver_attach+0xb0/0xb8
[    [email protected]] [<ffffffc001457c3c>] bus_for_each_dev+0x68/0xac
[    [email protected]] [<ffffffc001459684>] driver_attach+0x28/0x34
[    [email protected]] [<ffffffc00145928c>] bus_add_driver+0x158/0x210
[    [email protected]] [<ffffffc00145a624>] driver_register+0x64/0x124
[    [email protected]] [<ffffffc00145bc30>] __platform_driver_register+0x74/0x84
[    [email protected]] [<ffffffc001e36d4c>] amhdmitx_init+0x5c/0xa4
[    [email protected]] [<ffffffc0010816a4>] do_one_initcall+0xd4/0x138
[    [email protected]] [<ffffffc001dfe990>] kernel_init_freeable+0x19c/0x23c
[    [email protected]] [<ffffffc001a05d48>] kernel_init+0x1c/0xdc
[    [email protected]] ---[ end trace da93876e7f41ceba ]---
[    [email protected]] ------------[ cut here ]------------
[    [email protected]] WARNING: CPU: 0 PID: 1 at /home/work/data/jenkins/workspace/transformers/common/drivers/base/core.c:549 device_create_file+0xa4/0xbc()
[    [email protected]] Attribute prefer_mode: write permission without 'store'
[    [email protected]] Modules linked in:
[    [email protected]] CPU: 0 PID: 1 Comm: swapper/0 Tainted: G        W    3.14.29-301482-g2d0e095 #1
[    [email protected]] Call trace:
[    [email protected]] [<ffffffc0010894d8>] dump_backtrace+0x0/0x144
[    [email protected]] [<ffffffc001089638>] show_stack+0x1c/0x28
[    [email protected]] [<ffffffc001a0b108>] dump_stack+0x74/0xb8
[    [email protected]] [<ffffffc0010a0088>] warn_slowpath_common+0x98/0xc0
[    [email protected]] [<ffffffc0010a0124>] warn_slowpath_fmt+0x74/0x88
[    [email protected]] [<ffffffc001454cd4>] device_create_file+0xa0/0xbc
[    [email protected]] [<ffffffc00163fa20>] amhdmitx_probe+0x2b8/0x924
[    [email protected]] [<ffffffc00145bc68>] platform_drv_probe+0x28/0x60
[    [email protected]] [<ffffffc001459bd4>] really_probe+0xd4/0x244
[    [email protected]] [<ffffffc001459e68>] __driver_attach+0xb0/0xb8
[    [email protected]] [<ffffffc001457c3c>] bus_for_each_dev+0x68/0xac
[    [email protected]] [<ffffffc001459684>] driver_attach+0x28/0x34
[    [email protected]] [<ffffffc00145928c>] bus_add_driver+0x158/0x210
[    [email protected]] [<ffffffc00145a624>] driver_register+0x64/0x124
[    [email protected]] [<ffffffc00145bc30>] __platform_driver_register+0x74/0x84
[    [email protected]] [<ffffffc001e36d4c>] amhdmitx_init+0x5c/0xa4
[    [email protected]] [<ffffffc0010816a4>] do_one_initcall+0xd4/0x138
[    [email protected]] [<ffffffc001dfe990>] kernel_init_freeable+0x19c/0x23c
[    [email protected]] [<ffffffc001a05d48>] kernel_init+0x1c/0xdc
[    [email protected]] ---[ end trace da93876e7f41cebb ]---
[    [email protected]] hdmitx: system: not find match init-data
[    [email protected]] hdmitx: system: not find match pwr-ctl
[    [email protected]] hdmitx hpd irq = 89
[    [email protected]] hdmitx20: Mapped PHY: 0xc0800000
[    [email protected]] hdmitx20: Mapped PHY: 0xc1104400
[    [email protected]] hdmitx20: Mapped PHY: 0xc8100000
[    [email protected]] hdmitx20: Mapped PHY: 0xc8834000
[    [email protected]] hdmitx20: Mapped PHY: 0xc883a000
[    [email protected]] hdmitx20: Mapped PHY: 0xc883c000
[    [email protected]] hdmitx20: Mapped PHY: 0xd0100000
[    [email protected]] hdmitx20: Mapped PHY: 0xda83a000
[    [email protected]] hdmitx: alread display in uboot 0x10
[    [email protected]] avmute set to 1
[    [email protected]] vout_serve: vout_init_module
[    [email protected]] tv_vout: tv_set_current_vmode[759]fps_target_mode=16
[    [email protected]] hdmitx: system: irq 2
[    [email protected]] tv_vout: mode is 16,sync_duration_den=1,sync_duration_num=60
[    [email protected]] tv_vout: already display in uboot
[    [email protected]] vout_serve: vinfo mode is: 1080p60hz
[    [email protected]] vout_serve: init mode 1080p60hz
[    [email protected]] vout_serve: create vout attribute OK
[    [email protected]] vout_serve: meson_vout_probe OK
[    [email protected]] logo: logo_init
[    [email protected]] osd_rdma: osd_rdma_init: rdma_table p=0x34841000,op=0x34841000 , v=0xffffff80000a9000
[    [email protected]] osd_rdma: osd rdma request irq as second interrput function!
[    [email protected]] Advanced Linux Sound Architecture Driver Initialized.
[    [email protected]] Bluetooth: Core ver 2.18
[    [email protected]] NET: Registered protocol family 31
[    [email protected]] Bluetooth: HCI device and connection manager initialized
[    [email protected]] Bluetooth: HCI socket layer initialized
[    [email protected]] Bluetooth: L2CAP socket layer initialized
[    [email protected]] Bluetooth: SCO socket layer initialized
[    [email protected]] cfg80211: Calling CRDA to update world regulatory domain
[    [email protected]] NetLabel: Initializing
[    [email protected]] NetLabel:  domain hash size = 128
[    [email protected]] NetLabel:  protocols = UNLABELED CIPSOv4
[    [email protected]] NetLabel:  unlabeled traffic allowed by default
[    [email protected]] Switched to clocksource arch_sys_counter
[    [email protected]] ktrace : kp ktrace init OK
[    [email protected]] ktrace : event ktrace init OK
[    [email protected]] ktrace : mm ktrace init OK
[    [email protected]] ktrace : sched ktrace init OK
[    [email protected]] ktrace : binder ktrace init OK
[    [email protected]] ktrace : cpufreq ktrace init OK
[    [email protected]] ktrace : ktrace init OK
[    [email protected]] [amlatvdemod..]aml_atvdemod_init.
[    [email protected]] NET: Registered protocol family 2
[    [email protected]] TCP established hash table entries: 8192 (order: 4, 65536 bytes)
[    [email protected]] TCP bind hash table entries: 8192 (order: 5, 131072 bytes)
[    [email protected]] TCP: Hash tables configured (established 8192 bind 8192)
[    [email protected]] TCP: reno registered
[    [email protected]] UDP hash table entries: 512 (order: 2, 16384 bytes)
[    [email protected]] UDP-Lite hash table entries: 512 (order: 2, 16384 bytes)
[    [email protected]] NET: Registered protocol family 1
[    [email protected]] aml_wifi wifi.31: [wifi_dev_probe] no power_on_pin2
[    [email protected]] aml_wifi wifi.31: [wifi_dev_probe] set pwm as 32k output
[    [email protected]] aml_wifi wifi.31: [wifi_dev_probe] interrupt_pin=241
[    [email protected]] aml_wifi wifi.31: [wifi_dev_probe] irq_num=100, irq_trigger_type=0
[    [email protected]] aml_wifi wifi.31: [wifi_dev_probe] power_on_pin=229
[    [email protected]] aml_wifi wifi.31: [wifi_dev_probe] clock_32k_pin=0
[    [email protected]] aml_wifi wifi.31: [wifi_setup_dt] wifi_setup_dt
[    [email protected]] aml_wifi wifi.31: [wifi_setup_dt] interrupt_pin(241)
[    [email protected]] aml_wifi wifi.31: [wifi_setup_dt] power_on_pin(229)
[    [email protected]] Unpacking initramfs...
[    [email protected]] Freeing initrd memory: 672K (ffffffc033ded000 - ffffffc033e95000)
[    [email protected]] futex hash table entries: 1024 (order: 4, 65536 bytes)
[    [email protected]] audit: initializing netlink subsys (disabled)
[    [email protected]] audit: type=2000 audit(1.470:1): initialized
[    [email protected]] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[    [email protected]] VFS: Disk quotas dquot_6.5.2
[    [email protected]] hdmitx: plugin
[    [email protected]] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    [email protected]] fuse init (API version 7.22)
[    [email protected]] msgmni has been set to 1679
[    [email protected]] NET: Registered protocol family 38
[    [email protected]] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 247)
[    [email protected]] io scheduler noop registered
[    [email protected]] io scheduler deadline registered
[    [email protected]] io scheduler cfq registered (default)
[    [email protected]] meson-rng c8834000.rng: hwrng registered
[    [email protected]] loop: module loaded
[    [email protected]] zram: Created 1 device(s) ...
[    [email protected]] tun: Universal TUN/TAP device driver, 1.6
[    [email protected]] tun: (C) 1999-2004 Max Krasnyansky <[email protected]>
[    [email protected]] PPP generic driver version 2.4.2
[    [email protected]] PPP BSD Compression module registered
[    [email protected]] PPP Deflate Compression module registered
[    [email protected]] PPP MPPE Compression module registered
[    [email protected]] NET: Registered protocol family 24
[    [email protected]] hdmitx: edid: check sum valid
[    [email protected]] hdmitx: edid: check sum valid
[    [email protected]] hdmitx: edid: blk0 raw data
[    [email protected]] 00ffffffffffff003674010be903000000100103804627780a1990a755469824
[    [email protected]] 10494b2108008bc0814081c061400101010101010101011d007251d01e206e28
[    [email protected]] 5500c48e2100001e011d8018711c1620582c2500c48e2100009e000000fc0050
[    [email protected]] 524f4a4543544f52530a2020000000fd0016500e5b10000a20202020202001e1
[    [email protected]] 
[    [email protected]] 
[    [email protected]] hdmitx: edid: blk1 raw data
[    [email protected]] 02031df24a0102038405101293141f230907078301000065030c0010008c0ad0
[    [email protected]] 8a20e02d10103e9600138e21000018011d00bc52d01e20b8285540c48e210000
[    [email protected]] 1e011d80d0721c1620102c2580c48e2100009e8c0ad08a20e02d10103e9600c4
[    [email protected]] 8e210000188c0ad090204031200c405500c48e2100001800000000000000002b
[    [email protected]] 
[    [email protected]] 
[    [email protected]] EDID Parser:
[    [email protected]] hdmitx: edid: find IEEEOUT
[    [email protected]] 
[    [email protected]] hdmitx: edid: check sum valid
[    [email protected]] hdmitx: edid: check sum valid
[    [email protected]] hdmitx: update RX hdr info 0
[    [email protected]] [RX]-receive ksv list len:1,depth:1,cas:0,dev:0
[    [email protected]] hdmitx: video: get current mode: 1080p60hz
[    [email protected]] hdmitx: update rx hdr info 0
[    [email protected]] hdmitx: get ext_name 
[    [email protected]] hdmitx: system: [set_disp_mode_auto] ALREADY init VIC = 16
[    [email protected]] hdmtix: set audio
[    [email protected]] hdmitx tx_aud_src = 0
[    [email protected]] hdmitx: system: irq 80000001
[    [email protected]] hdmitx: fs = 0, cd = 4, tmds_clk = 148500
[    [email protected]] hdmitx aud_n_para = 6144
[    [email protected]] hdmitx set channel status
[    [email protected]] Start = 0x10000100   End = 0x100001ff
[    [email protected]] [0x10000103]: 0x00000008
[    [email protected]] [0x10000104]: 0x00000001
[    [email protected]] [0x10000170]: 0x00000010
[    [email protected]] [0x10000180]: 0x000000ff
[    [email protected]] [0x10000181]: 0x000000ff
[    [email protected]] [0x10000182]: 0x00000003
[    [email protected]] [0x10000183]: 0x00000007
[    [email protected]] [0x10000184]: 0x0000003f
[    [email protected]] [0x10000185]: 0x00000002
1st October 2019, 08:23 AM |#17  
Junior Member
Thanks Meter: 0
 
More
MDZ-22 ab crashed
Hello togehter,
I new in the rforum and need support.

I think I crashed mz mdy-22ab bz upadting new version via USB, since this i cannot enter reoverz mode.

I followed the describtion to enter via UART and Putty and got the following.
Due the fact that i am not an expert i don^t know wht the puttz.log means.
Maybe some experts in the forum can help me.

Reset...
GXL:BL1:9ac50e:bb16dc;FEAT:BDFD71BC:0;POC:3;RCY:0; EMMC:0;READ:0;0.0;0.0;CHK:0;
TE: 99019

BL2 Built : 13:27:37, Oct 25 2017. gxl g56b77aa - [email protected]

_vcc5_power_init
rn5t567_power_init
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
i2c timeout
Board ID = 5
CPU clk: 1200MHz
DQS-corr enabled
DDR scramble enabled
DDR3 chl: Rank0+1 @ 912MHz - FAIL
DDR3 chl: Rank0 @ 912MHz - FAIL
DDR3 chl: Rank0 16bit @ 912MHz - FAIL
DDR4 chl: Rank0+1 @ 1008MHz - FAIL
DDR4 chl: Rank0 @ 1008MHz - FAIL
DDR4 chl: Rank0 16bit @ 1008MHz - FAIL
DDR init failed...
Reset...
GXL:BL1:9ac50e:bb16dc;FEAT:BDFD71BC:0;POC:3;RCY:0; EMMC:0;READ:0;0.0;0.0;CHK:0;
TE: 99323
1st January 2020, 09:51 PM |#18  
Member
Thanks Meter: 2
 
More
Same me..(((
25th February 2020, 02:51 PM |#19  
Junior Member
Thanks Meter: 0
 
More
I can't find any link to download Armbian_5.34_S9xxx_Ubuntu_xenial_4.9.40_mate_20171 112. Can someone reupload it?
26th March 2020, 09:10 AM |#20  
Junior Member
Thanks Meter: 0
 
More
Can I do it with regular usb rs232 cable?I have to solder it?Is there newer builds avalible?
Post Reply Subscribe to Thread

Guest Quick Reply (no urls or BBcode)
Message:
Previous Thread Next Thread
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes