Recent content by jaytec0007

Hi Slim great rom and I found a slimbox 10.4 firmware for tx3 mini AP6330 on 4pda and the burning and everything else is working great except the remote control OK, Home, Menu and Back key doesn't work. I couldn't find any forum about your firmware and the tx3 mini AP6330 so its the only place I...

Hi Slim were you able to give a look for 10.2 for transpeed X3 pro firmware called sbx_h9x3_atv_v10_2? I am able to flash firmware without any problem and i get boot logo on first start with the blue turning purple background but after a few minutes the box reboot and goes directly into twrp. I...

Hi great job with 10.2, im really happy to be able to remotely do everything with teamviewer quicksupport again like older versions. I have just 1 issue, I also have a Transpeed X3 Pro s905x3, i downloaded the right firmware called sbx_h9x3_atv_v10_2 and flash it with UBT and everything goes...

Really hoped that quicksupport would work again like in v9 and older, i can see remote screen but cant control or do anything else even with addon, must be a firmware permission mising or different than v9 and older

I've try with different version of quicksupport addons and also AOSP but doesn't change nothing. On pass versions of the firmware v8, v9 there was no need of installing the addon like most of the boxes and we were able to connect remotely and do everything when needed, now we can only see the...

Hi i have tx9s, tx3 s905x3 and also transpeed x3 pro and everything is great but with version 10 when i remotely connect with my PC to teamviewer quicksupport i can only see the remote screen but cant control anything. Before on version 9 and older i was able to remotely see the screen and do...

Hi really nice rom by the way but i have a small issue, with all other version when i install teamviewer quicksupport on them i was able with my pc to connect remotely and control everything, install apps, change settings well everything like if i was there and also able to see screen from the...

Hi all, I have mxq pro 4k whit board S905XQ v2.0 and I tried to install v2ff and now when it boot light turn blue but screen stays black. Ive tried to find firmware for my board but couldn't find it anywhere. I download and tried more than 25 firmwares for mxq pro s905x and whit usb burning...

First I had to edit qcn file with my imei and restore qcn file with Qfil after restoring firmware, after that I was able to get network back but without wifi and because network data is turned off by default I wasn't able to activate the phone. Finally flashed persit in fastboot and BAM wifi is...

Sthor ive been finally able to fix it after flashing persist in fastboot, I'm so happy tanks for everything I wouldn't be able without your help tanks again

ok tanks ill try both and let you know if one of them fix my problem Jay ---------- Post added at 08:26 AM ---------- Previous post was at 07:51 AM ---------- Stnor, I try putting the sim card to slot 2 and its the same, I get 3g and network bars in status bar but not able to activate, I...

Hi sthor I was able to restore imei to the phone after flashing 075 and now I can see 3g on status bar with network bar but I still not able to activate it. The phone is really laggy sometime it take 5 minutes to pass the screen where you have to clic on Quick settings and when I pass that...

Great! and tanks a lot for everything and I let you know if everything work fine

In step 7 I type again the first imei? you sure I shouldn't put the second imei in step 7 and step 8 cause I already put the first imei in step 4 and 5

Hi I'm a little bit lost whit HxD, I downloaded QCN backup and install it. When you say open the QCN templet in HxD do you mean clic on Files and after clic on New? If so after that I did Ctrl-f and open the search box then go to Hex values, and I put 08 5A 46 44 45 65 66 67 76 in Search for...