FORUMS
Remove All Ads from XDA

[KERNEL][02-07-2019]ThundeRStormS Kernel[Samsung Galaxy S7 flat/edge][TW9.0 NFE/N8]

943 posts
Thanks Meter: 621
 
By nalas, Senior Member on 14th April 2019, 12:02 PM
Post Reply Email Thread
ThundeRStormS "Galaxy S7/S7edge (SM-G930/935 F/FD) NFE/N8 -PIE kernel"

Compatibility notes :
NFE/N8 PIE - Android 9.0.0 STOCK RELEASE odexed roms
S7 Stock NFE /N8 PIE ROMs - G930/G935 F/FD
'I don't use any ported rom so I can't check it'

This kernel is for stock rom odexed.
(If You want to install ported roms - pls uncheck Priv fix for stock Roms in installation process and select fix for deodexed and ported roms and look at Installation section in OP)

The kernel use an AROMA installer to help guide you through the installation.


Recommended Apps:
To tweak most of the settings in the kernel, I recommend using ThunderTweaks app.
_________________________________________________

IMPORTANT INFORMATIONS:
1. WARNING: YOU UNDERSTAND THAT INSTALLING CUSTOM FIRMWARE/ROM/KERNEL IS AT YOUR OWN RISK!!!
2. YOUR WARRANTY CAN BE VOID.
"I am not responsible for bricked devices, dead SD cards, thermonuclear war, or you getting fired because the alarm app failed.
Please do some research if you have any concerns about features included in this kernel before flashing it! YOU are choosing to make these modifications, and if you point
the finger at me for messing up your device, You can't blame me for this fact."

3. NO REQUESTS!!!

_________________________________________________

KERNEL FEATURES:
- based on stock Samsung kernel U4CSC4
- based on stock Samsung ramdisk U4CSC4 | sepolicy 03.2019
- based on latest ELS source ||3.18.91||
- Flat and Edge support
- Odexed / Deodexed Roms
- aroma installer
- init.d support
- lot of CPU governors
- Conservative governor editable (now You can edit governors values)
- lower than stock's values for big and little CPUs frequencies to 208/130 MHz
- lower than stock's values for GPU frequencies to 112MHz
- lot of I/O schedulers
- TCP : cubic, htcp, reno, bic, westwood, vegas, veno, lia, olia, wvegas
- SELinux status to permissive/enforcing
- disasbled DM-Verity, Knox, RKP, Tima, Rooting Restriction
- Magisk, ThunderTweaks
- fixed TWRP 3.2.3-0 by Tkkg1994
- Spectrum support
- ArchPower
- PWM Flicker Free
- CPU voltage control
- standard wakelocks
- Boeffla wakelock control
- Battery settings controls
- ABS clock fixed to 64bit
- GPU Thermal Throttling
- GPU voltage control
- GPU OC to 806 MHz
- F2FS files support
- Fsync control and CRC
- Dynamic Fsync
- Gentle Sleepers support
- Wireguard VPN support
- Moro Sound Drivers
- LED controls
- Support 9 Spectrum Profiles with ThundeRStormS profiles
- ThunderStrom CPU governor based on Interactive with new editable feature
- Gestures Wakeup controls
- Support Hotplugs : Alucard, AiO, Zen Decision and AutoSMP, Mako, Cluster, Thunderbolt, Lazy, Fast, MSM - first kernel with this features
..MTweaks do not support all features of hotplugs so all settings are not available to change
..You can do it via file browser and change values in sys files of this module - some parts.
- VNSwap default is turned ON | If You want it OFF, select in Aroma Installer.
- ZRAM max file is changed to 4,0GB but default is turned OFF | disk space for ZRAM is editable.
- Input Boost drivers and control for CPU each core | first kernel with this feature for S7 TW
- Input Boost for CPU | for Little.big clusters first kernel with this feature for S7 TW
- Fingerprint Boost | first kernel with this feature for S7 TW
- this kernel is not for people who want to get big bentchmark scores, OC, etc.
- this kernel is for daily use for better battery life with good balanced work

What is not included:
- no OC for CPU
- no synapse support
_________________________________________________

INSTALLATION PROCESS:

FOR STOCK ODEX/DEODEX ROMS
  • FIRST - Clear cache apps like Kernel Adiutor or MTweaks or another one in system app menager !!!
  • Backup EFS and KERNEL as always in TWRP !!!
  • Download the latest kernel version zip file
  • Go to recovery
  • Flash the kernel zip with root or not
  • Choose aroma selection
  • Flash Magisk separately or with Aroma installer
  • Reboot
  • Mtweaks app is copied to Your External_SDcard in MTweaks folder - You can install it manually.

If You wnat to flash this kernel and have installed another custom kernel like MoRoKernel or Arianoxx, You have to clear MTweaks or Kernel Adiutor cache before You install.
If You dont want one of the possibilities for root inside Aroma Installer please choose no root and next flash any root mods manually.

PROBLEMS / BUGS:

Thanks for reports.
_________________________________________________

CREDITS AND THANKS:
- The Linux Kernel Archive for the Linux Patches https://www.kernel.org/
- Samsung Open Source Release Center for the Source code http://opensource.samsung.com/
- Project: Exynos-Linux-Stable for updated ELS Linux source codes https://github.com/exynos-linux-stable
- @morogoku and @francitato02 for his help and explanation of the compile and configure kernel processing, codes and commits
- @djb77 for his help and explanation of the compile and configure kernel processing, codes and commits
- @Tkkg1994, @francitato02, @Noxxxious, @farovitus, and @mwilky for help, codes and commits
- @osm0sis for Android Image Kitchen and anykernel2 https://forum.xda-developers.com/sho....php?t=2073775
- Magisk and SuperSu Team for root method
- @ModX81 for new base of ramdisk, CP and BL from Samsung
- Tester : @wille95, @youpeero, @TheesKyr, @cenelyanto, @Franz S., @phghost, @insanowsky, @Shariq3422
- Tester, idea & support : @matt_988, @Kyo-Ito
_________________________________________________

SOURCE of the kernel:
GitHub: https://github.com/ThunderStorms21th...-S7-Pie-kernel
_________________________________________________

Contributors:
@nalas, @callidus_ex_de_latebros, @VHFG22
ThundeRStormS Team
_________________________________________________

DISCUSSION:
Telegram Group: Link
Telegram News Channel: Link
_________________________________________________

Version Information:
Statsus : Stable
Current version : 1.8
Release Date : 2019-07-02


--------------------------------------------------------------------------------
DONATION:
If you liked my work, you can collaborate by giving thanks and with some donation to continue working hard.
Thank you very much to all.
DONATION

CHANGELOGS & DOWNLOADS in 2nd post
The Following 18 Users Say Thank You to nalas For This Useful Post: [ View ] Gift nalas Ad-Free
 
 
14th April 2019, 12:03 PM |#2  
OP Senior Member
Thanks Meter: 621
 
More
CHANGELOGS and DOWNLOADS
CHANGELOGS:

Version v1.8
  • ROM PIE NFE and N8 support
  • Samsung sources U4CSC4
  • Samsung ramdisk U4CSC4
  • ThunderTweaks 1.0.1 | adaptaded to ThundeRStormS kernels |
  • Flat and Edge now supported
  • Magisk 19.3 back again
  • TWRP 3.3.0-0 fixed by AJ's
  • Knox 0x0 & SafetyNet with SuperSU and Magisk
  • SuperSU 2.82SR5 + SuHide v1.09
  • Linux 3.18.91 Samsung source
  • Game Tools Fix - thx to MoroGoku
  • Camera Fix - now SONY/SAMSUNG works
  • CPU Freq range : Higher Freq 2600/1586 MHz and Low Freq at 208/130 MHz
  • CPU Freq setup : Higher Freq 2288/1586 MHz and Low Freq at 312/234 MHz
  • CPU Freq setup : changes in voltage tables for lower power consuption for boot and normal work time
  • Fixed ABS clock to 64bit
  • Compiler : aarch64-linux-android-4.9
  • Spectrum and profiles supported
  • Iris service disabled
  • Support now 10 Spectrum Profiles with NEW ThundeRSTormS profiles
  • Added NEW Thunderstorm CPU Governor based on Interactive with new editable feature
  • Added TTL support for IP
  • Bluetooth OREO drivers
  • Added new I/O scheds : Anxiety and Maple
  • Some CPU governors are updated
  • Wireguard VPN supported
  • Gestures Wakeup supported
  • Added SSP sensor battery drain
  • Added Hotplugs : Alucard, AiO, Zen Decision and AutoSMP, Mako, Cluster.
  • ZRAM max files set at 4,0GB - default OFF | Now is editable by user.
  • VNSwap truned ON by default | If You want to turn it OFF You have to select one option for it in Aroma Installer.
  • Fingerprint Boost support - default turned OFF.
  • Added Input Boost for big.LITTLE clusters.
  • Fixed AiO and AutoSMP Hotplugs for 2 Clusters Octa cores Exynos
  • ZSWAP RAM Pool set max from 50 to 60%
  • Possibly Fixed drain battery
  • SELinux Permissive
Version v1.7
  • ROM PIE NFE and N8 support
  • Samsung sources U4CSC4
  • Samsung ramdisk U4CSC4
  • ThunderTweaks 1.0.0 | adaptaded to ThundeRStormS kernels |
  • Flat and Edge now supported
  • Magisk 19.0 back again
  • TWRP 3.3.0-0 fixed by AJ's
  • Knox 0x0 & SafetyNet with SuperSU and Magisk
  • SuperSU 2.82SR5 + SuHide v1.09
  • Linux 3.18.91 Samsung source
  • Game Tools Fix - thx to MoroGoku
  • Camera Fix - now SONY/SAMSUNG works
  • CPU Freq range : Higher Freq 2600/1586 MHz and Low Freq at 208/130 MHz
  • CPU Freq setup : Higher Freq 2288/1586 MHz and Low Freq at 312/234 MHz
  • CPU Freq setup : changes in voltage tables for lower power consuption for boot and normal work time
  • Fixed ABS clock to 64bit
  • Compiler : aarch64-linux-android-4.9
  • Spectrum and profiles supported
  • Iris service disabled
  • Support now 5 Spectrum Profiles with NEW ThundeRSTormS profile
  • Added NEW Thunderstorm CPU Governor based on Interactive with new editable feature
  • Added TTL support for IP
  • Added new I/O scheds : Anxiety and Maple
  • Some CPU governors are updated
  • Wireguard VPN supported
  • Gestures Wakeup supported
  • Added SSP sensor battery drain
  • Added Hotplugs : Alucard, AiO, Zen Decision and AutoSMP, Mako, Cluster | MTweaks don't support some settings yet but will be in the future - thx to Moro.
  • ZRAM max files set at 2,5GB - default OFF | Now is editable by user.
  • VNSwap truned ON by default | If You want to turn it OFF You have to select one option for it in Aroma Installer.
  • Fingerprint Boost support - default turned OFF | MTweaks don't support toggle yet.
  • Fixed AiO and AutoSMP Hotplugs for 2 Clusters Octa cores Exynos
  • ZSWAP RAM Pool set max from 50 to 60%
  • Possibly Fixed drain battery
  • SELinux Permissive

Version v1.6
  • ROM PIE NFE and N8 support
  • Samsung sources U4CSC4
  • Samsung ramdisk U4CSC4
  • MTweaks 2.14.0 | fixed installation
  • Flat and Edge now supported
  • Magisk 19.0 back again
  • TWRP 3.3.0-0 fixed by AJ's
  • Knox 0x0 & SafetyNet with SuperSU and Magisk
  • SuperSU 2.82SR5 + SuHide v1.09
  • Linux 3.18.91 Samsung source
  • Game Tools Fix - thx to MoroGoku
  • Camera Fix - now SONY/SAMSUNG works
  • CPU Freq range : Higher Freq 2600/1586 MHz and Low Freq at 208/130 MHz
  • CPU Freq setup : Higher Freq 2288/1586 MHz and Low Freq at 312/234 MHz
  • CPU Freq setup : changes in voltage tables for lower power consuption for boot and normal work time
  • Fixed ABS clock to 64bit
  • Compiler : aarch64-linux-android-4.9
  • Spectrum and profiles supported
  • Iris service disabled
  • Added TTL support for IP
  • Added new I/O scheds : Anxiety and Maple
  • Some CPU governors are updated
  • Wireguard VPN supported
  • Gestures Wakeup supported
  • Added SSP sensor battery drain
  • Added Hotplugs : Alucard, AiO, Zen Decision and AutoSMP, Mako, Cluster | MTweaks don't support some settings yet but will be in the future - thx to Moro.
  • ZRAM max files set at 2,5GB - default OFF | Now is editable by user.
  • VNSwap truned ON by default | If You want to turn it OFF You have to select one option for it in Aroma Installer.
  • Fingerprint Boost support - default turned ON | MTweaks don't support toggle yet but will be in the future - thx to Moro.
  • Fixed AiO and AutoSMP Hotplugs for 2 Clusters Octa cores Exynos
  • ZSWAP RAM Pool set max from 50 to 60%
  • Possibly Fixed drain battery
  • SELinux Permissive

Version v1.5
  • Samsung sources U4CSC4
  • Samsung ramdisk U4CSC4
  • MTweaks 2.14.0 | fixed installation
  • Flat and Edge now supported
  • Magisk 19.0 back again
  • Knox 0x0 & SafetyNet with SuperSU and Magisk
  • SuperSU 2.82SR5 + SuHide v1.09
  • Linux 3.18.91 Samsung source
  • Game Tools Fix - thx to MoroGoku
  • Camera Fix - now SONY/SAMSUNG works
  • CPU Freq range : Higher Freq 2600/1586 MHz and Low Freq at 208/130 MHz
  • CPU Freq setup : Higher Freq 2288/1586 MHz and Low Freq at 312/234 MHz
  • CPU Freq setup : changes in voltage tables for lower power consuption for boot and normal work time
  • Fixed ABS clock to 64bit
  • Compiler : aarch64-linux-android-4.9
  • Spectrum and profiles supported
  • Iris service disabled
  • Added TTL support for IP
  • Added new I/O scheds : Anxiety and Maple
  • Some CPU governors are updated
  • Wireguard VPN supported
  • Gestures Wakeup supported
  • Added SSP sensor battery drain
  • Added Hotplugs : Alucard, AiO, Zen Decision and AutoSMP | MTweaks don't support some settings yet but will be in the future - thx to Moro.
  • ZRAM max files set at 2,5GB - default OFF | Now is editable by user.
  • VNSwap truned ON by default | If You want to turn it OFF You have to select one option for it in Aroma Installer.
  • Fingerprint Boost support - default turned ON | MTweaks don't support toggle yet but will be in the future - thx to Moro.
  • Possibly Fixed drain battery
  • SELinux Permissive
  • Rest like in TS-PIE v1.4

Version v1.4
  • Samsung sources U4CSC4
  • Samsung ramdisk U4CSC4
  • MTweaks 2.14.0 | fixed installation
  • Flat and Edge now supported
  • Magisk 19.0 back again
  • Knox 0x0 & SafetyNet with SuperSU and Magisk
  • SuperSU 2.82SR5 + SuHide v1.09
  • Linux 3.18.91 Samsung source
  • Game Tools Fix - thx to MoroGoku
  • Camera Fix - now SONY/SAMSUNG works
  • CPU Freq range : Higher Freq 2600/1586 MHz and Low Freq at 208/130 MHz
  • CPU Freq setup : Higher Freq 2288/1586 MHz and Low Freq at 312/234 MHz
  • CPU Freq setup : changes in voltage tables for lower power consuption for boot and normal work time
  • Fixed ABS clock to 64bit
  • Compiler : aarch64-linux-android-4.9
  • Spectrum and profiles supported
  • Iris service disabled
  • Wireguard VPN supported
  • Gestures Wakeup supported
  • Added SSP sensor battery drain
  • Added Hotplugs : Alucard, AiO, Zen Decision and AutoSMP | MTweaks don't support some settings yet but will be in the future - thx to Moro.
  • ZRAM max files set at 2,5GB - default OFF
  • VNSwap truned OFF by default | If You want to turn it ON You have to delete TS script from Init.d folder
  • Fingerprint Boost support - default turned ON | MTweaks don't support toggle yet but will be in the future - thx to Moro.
  • Possibly Fixed drain battery
  • SELinux Permissive
  • Rest like in TS-PIE v1.3

Version v1.3
  • Samsung sources U4CSC4
  • Samsung ramdisk U4CSC4
  • MTweaks 2.14.0 | fixed installation
  • Flat and Edge now supported
  • Magisk 19.0 back again
  • Knox 0x0 & SafetyNet with SuperSU and Magisk
  • SuperSU 2.82SR5 + SuHide v1.09
  • Linux 3.18.91 Samsung source
  • Game Tools Fix - thx to MoroGoku
  • Camera Fix - now SONY/SAMSUNG works
  • CPU Freq range : Higher Freq 2600/1586 MHz and Low Freq at 208/130 MHz
  • CPU Freq setup : Higher Freq 2288/1586 MHz and Low Freq at 312/234 MHz
  • CPU Freq setup : changes in voltage tables for lower power consuption for boot and normal work time
  • Fixed ABS clock to 64bit
  • Compiler : aarch64-linux-android-4.9
  • Spectrum and profiles supported
  • Iris service disabled
  • Wireguard VPN supported
  • Gestures Wakeup supported
  • Added SSP sensor battery drain
  • Possibly Fixed drain battery
  • SELinux Permissive
  • Rest like in TS-PIE v1.2

Version v1.2
  • Samsung sources U4CSC4
  • Samsung ramdisk U4CSC4
  • MTweaks 2.14.0 | fixed installation
  • Removed Smartpack-Kernel Manager v7.5
  • Flat and Edge now supported
  • Magisk 19.0 back again
  • Knox 0x0 & SafetyNet with SuperSU and Magisk
  • SuperSU 2.82SR5 + SuHide v1.09
  • Linux 3.18.91 Samsung source
  • Game Tools Fix - thx to MoroGoku
  • Camera Fix - now SONY/SAMSUNG works
  • CPU Freq range : Higher Freq 2600/1586 MHz and Low Freq at 208/130 MHz
  • CPU Freq setup : Higher Freq 2288/1586 MHz and Low Freq at 312/234 MHz
  • CPU Freq setup : changes in voltage tables for lower power consuption for boot and normal work time
  • Fixed ABS clock to 64bit
  • Compiler : aarch64-linux-android-4.9
  • Spectrum and profiles supported
  • Wireguard VPN supported
  • Added SSP sensor battery drain
  • Possibly Fixed drain battery
  • SELinux Permissive
  • Rest like in TS-PIE v1.1

Version v1.1
  • Samsung sources U4CSC4
  • Samsung ramdisk U4CSC4
  • MTweaks 2.14.0
  • Smartpack-Kernel Manager v7.5
  • Flat and Edge now supported
  • Magisk 18.1 | System files and folders now are visible - problem of Magisk 19.0
  • Knox 0x0 & SafetyNet with SuperSU and Magisk
  • SuperSU 2.82SR5 + SuHide v1.09
  • Linux 3.18.91 Samsung source
  • Game Tools fix - thx to MoroGoku
  • CPU Freq range : Higher Freq 2600/1586 MHz and Low Freq at 416/338 MHz
  • CPU Freq setup : Higher Freq 2288/1586 MHz and Low Freq at 416/338 MHz
  • Fixed ABS clock to 64bit
  • Compiler : aarch64-linux-android-4.9
  • Spectrum and profiles supported
  • Wireguard VPN supported
  • Added SSP sensor battery drain
  • Possibly Fixed drain battery
  • SELinux Permissive
  • Rest like in TS-PIE v1.0.1

Version v1.0.1
  • Samsung sources U4CSC4
  • Samsung ramdisk U4CSC4
  • MTweaks 2.14.0
  • Smartpack-Kernel Manager v7.5
  • Flat and Edge now supported
  • Magisk 18.1 | now System files are visible - problem of Magisk 19.0
  • Knox 0x0 & SafetyNet with SuperSU and Magisk
  • SuperSU 2.82SR5 + SuHide v1.09
  • Linux 3.18.91 Samsung source
  • Game Tools fix - thx to MoroGoku
  • CPU Freq range : Higher Freq 2600/1586 MHz and Low Freq at 416/338 MHz
  • CPU Freq setup : Higher Freq 2288/1586 MHz and Low Freq at 416/338 MHz
  • Fixed ABS clock to 64bit
  • Fixed some SCSI drivers
  • Added ArchPower support
  • Added Dynamic Fsync and Gentle Sleepers support
  • Compiler : aarch64-linux-android-4.9
  • Spectrum and profiles supported
  • Wireguard VPN supported
  • Possibly Fixed drain battery
  • SELinux Permissive
  • Rest like in TS-PIE v1.0

Version v1.0
  • Samsung sources U4CSC4
  • Samsung ramdisk U4CSC4
  • MTweaks 2.13.5
  • Smartpack-Kernel Manager v7.5
  • Flat and Edge now supported
  • Magisk 19.0
  • Knox 0x0 & SafetyNet with SuperSU and Magisk
  • SuperSU 2.82SR5 + SuHide v1.09
  • Linux 3.18.91 Samsung source
  • Unlocked big CPU 4 cores to 2600MHz
  • CPU Freq range : Higher Freq 2600/1586 MHz and Low Freq at 416/338 MHz
  • CPU Freq setup : Higher Freq 2288/1586 MHz and Low Freq at 416/338 MHz
  • GPU Freq: 112-806MHz Stock
  • Added GPU Throttling
  • Added CPU and GPU voltage control
  • Added GPU OC to 806MHz
  • Added Fsync - default turn off
  • Added CRC - default turn off
  • Added standard wakelocks
  • Added Boeflla wakelocks
  • Added Battery Store and settings control
  • Fixed ABS clock to 64bit
  • Compiler : aarch64-linux-android-4.9
  • Spectrum and profiles supported
  • Wireguard VPN supported
  • Possibly Fixed drain battery
  • Some CPU governors
  • Lot of I/O Shedulers
  • HMP settings : 760/240 and some freq chcnages
  • USB charge to 700MHz in normall mode
  • USB charge to 900MHz in fast mode
  • Added VENO, VEGAS to TCP, etc.
  • Lot of CPU governors
  • Added PWM Flicker Free - default turn off
  • Moro Sound Drivers
  • Led controls
  • SELinux Permissive

-------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------------

DOWNLOADS:
ThundeRStormS kernel v1.8 : GoogleDrive or androidfilehost |FOR S7 FLAT / EDGE|
ThundeRStormS kernel v1.7 : GoogleDrive or androidfilehost |FOR S7 FLAT / EDGE|
ThundeRStormS kernel v1.6 : GoogleDrive or androidfilehost |FOR S7 FLAT / EDGE|
ThundeRStormS kernel v1.5 : GoogleDrive or androidfilehost |FOR S7 FLAT / EDGE|
ThundeRStormS kernel v1.4 : GoogleDrive or androidfilehost |FOR S7 FLAT / EDGE|
ThundeRStormS kernel v1.3 : GoogleDrive or androidfilehost |FOR S7 FLAT / EDGE|
ThundeRStormS kernel v1.2 : GoogleDrive or androidfilehost |FOR S7 FLAT / EDGE|
ThundeRStormS kernel v1.1 : GoogleDrive or androidfilehost |FOR S7 FLAT / EDGE|
ThundeRStormS kernel v1.0.1 : GoogleDrive or androidfilehost |FOR S7 FLAT / EDGE|
ThundeRStormS kernel v1.0 : GoogleDrive or androidfilehost |FOR S7 FLAT / EDGE|
The Following 10 Users Say Thank You to nalas For This Useful Post: [ View ] Gift nalas Ad-Free
14th April 2019, 12:04 PM |#3  
OP Senior Member
Thanks Meter: 621
 
More
ThunderTweaks
ThunderTweaks is an app based on Kernel Adiutor Willi Ye next modded by MoRoGoKu (MTweaks) and Corsicanu (hKTweaks).

Big thx for them.

ThunderTweaks v1.0.1 for TS kernel v1.8 :
- based on ThunderTweaks v1.0.0
- added new ThundeRStormS Spectrum Profiles and support now 9 spectrum's profiles
- some improvments

ThunderTweaks v1.0.0 for TS kernel v1.7 :
- based on hKTweaks v1.1.5
- added full support for new AotoSMP hotplug adaptated to Exynos 8890 by ThundeRStormS team
- added fix for settings max ZRAM disk size up to 4GB
- added new ThundeRStormS Spectrum Profile and support now 5 spectrum's profiles
- first ThundeRStormS Kernel Manager

SOURCE:
https://github.com/ThunderStorms21th/ThunderTweaks

DOWNLOAD:
ThunderTweaks v1.0.1 : GoogleDrive | FOR S7 FLAT / EDGE |
ThunderTweaks v1.0.0 : GoogleDrive | FOR S7 FLAT / EDGE |
The Following 2 Users Say Thank You to nalas For This Useful Post: [ View ] Gift nalas Ad-Free
14th April 2019, 01:06 PM |#4  
Member
Thanks Meter: 28
 
More
In test from yesterday. All good for now
The Following User Says Thank You to matt_988 For This Useful Post: [ View ] Gift matt_988 Ad-Free
14th April 2019, 01:31 PM |#5  
OP Senior Member
Thanks Meter: 621
 
More
Quote:
Originally Posted by matt_988

In test from yesterday. All good for now

great to hear that
The Following 2 Users Say Thank You to nalas For This Useful Post: [ View ] Gift nalas Ad-Free
14th April 2019, 02:09 PM |#6  
rroyy's Avatar
Senior Member
Flag Istanbul
Thanks Meter: 569
 
More
Thank you!
15th April 2019, 06:45 AM |#7  
Member
Thanks Meter: 28
 
More
I can confirm, this kernel is a great compromise of battery life and performance, at 50% i've over 2 hours SOT, with normal use (S7 FLAT: spotify, email, whatsapp, excel, kiwi browser, maps, gps and bluetooth always on) i can easily arrive at full discharge with 4 hours and +. And my battery is 3 years old! Also standby consumption is fantastic, and phone is never hot!!!! I've attached a screenshot of battery life of S10E (3100 mah), a newer phone but not so good as S7 (3000 mah). Many thanks to dev.
Click image for larger version

Name:	Screenshot_20190415-072633_Kiwi Browser.jpg
Views:	788
Size:	112.3 KB
ID:	4742881
The Following User Says Thank You to matt_988 For This Useful Post: [ View ] Gift matt_988 Ad-Free
15th April 2019, 01:36 PM |#8  
OP Senior Member
Thanks Meter: 621
 
More
Quote:
Originally Posted by matt_988

I can confirm, this kernel is a great compromise of battery life and performance, at 50% i've over 2 hours SOT, with normal use (S7 FLAT: spotify, email, whatsapp, excel, kiwi browser, maps, gps and bluetooth always on) i can easily arrive at full discharge with 4 hours and +. And my battery is 3 years old! Also standby consumption is fantastic, and phone is never hot!!!! I've attached a screenshot of battery life of S10E (3100 mah), a newer phone but not so good as S7 (3000 mah). Many thanks to dev.
Attachment 4742881

Nice to hear enjoy then and be in touch in new updates

PS
3:35h on S10 ? ulalalal bad...
Dont panic - maybe I will buy s10e so I will arrive with my kernel too
The Following User Says Thank You to nalas For This Useful Post: [ View ] Gift nalas Ad-Free
15th April 2019, 03:04 PM |#9  
Member
Thanks Meter: 28
 
More
Quote:
Originally Posted by nalas

Nice to hear enjoy then and be in touch in new updates

PS
3:35h on S10 ? ulalalal bad...
Dont panic - maybe I will buy s10e so I will arrive with my kernel too

Not my, take from a web review , i will change my s7 when 5g is ready in my country, and for now s7 works well
21st April 2019, 08:31 PM |#10  
Member
Thanks Meter: 28
 
More
Hi @nalas, how to remove morosound and relative drivers? I don't want any tipe of sound mod, because decreasing speaker volume. Only want the good and old flat sound.
22nd April 2019, 10:30 AM |#11  
OP Senior Member
Thanks Meter: 621
 
More
You can turn off this in MTweaks but generaly this is default off so no changes any sound.
Quote:
Originally Posted by matt_988

Hi @nalas, how to remove morosound and relative drivers? I don't want any tipe of sound mod, because decreasing speaker volume. Only want the good and old flat sound.

Wysłane z mojego SM-N935F przy użyciu Tapatalka
Post Reply Subscribe to Thread

Guest Quick Reply (no urls or BBcode)
Message:
Previous Thread Next Thread
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes