FORUMS

Samsung Galaxy S7 Edge Charging Analysis

49 posts
Thanks Meter: 40
 
By jisddwqs, Member on 15th April 2016, 08:53 AM
Post Reply Email Thread
I visited tronsmart website and found an interesting article. You guys might need such useful information so I post it here. Please note that I have removed all of the products links in this post.

The Galaxy S7 Edge has been drawing lots of attention since its release on 2016 WMC this past February. It features a 5.5 inch AMOLED 2K display, powered by Android 6.0 OS and a built-in 3600 mAh Li battery. Now, the Galaxy S7 Edge is currently available on market, but we sourced one previously and have already spent several days of testing its charging capabilities to make this analysis for our readers.

The Samsung Galaxy S7 Edge is equipped with the latest Qualcomm Snapdragon 820 SoC, and it supports Qualcomm’s Quick Charge 2.0 technology. Tronsmart has tested the Galaxy S7 Edge charging with its original wall charger, with a OnePlus 2 original charger, and with Tronsmart’s latest WC1T, W2PTE wall charger and C2PTE charger.

The following is the charging result and analysis.


1) Samsung Galaxy S7 Edge original charger (with Quick Charge 2.0 technology)
Specification: INPUT AC100-240V
OUTPUT [email protected], [email protected]
Result: Total Charging time from battery level 0% to 100% is 1 hour and 34 mins with the original charger, check the table and chart below for details, minute by minute.

Chart 1
From the data, we can see in the first full hour, battery level has already reached 78%, the maximum charging voltage is 9.19V, and the current is 1.62A which is about 15W of maximum power. Then another 34 mins later, the battery level is fully charged. During the last 34 mins, charging voltage is around 9V, but current reduces from 1A to 0.5A approximately in the end. The whole charging process lines up with the basic principle of a standard phone charging system. Smartphone batteries are charged in two stages as we have discussed in the past. The first stage can be performed with a high amount of power and takes the battery up to around 80%. Then the second stage kicks in where the power is reduced as the battery is topped up to full. It is proven, once again, in the following charging tests.

2) OnePlus 2 Original Charger
Specification: INPUT: AC100-240V
OUTPT: [email protected]

Result: It takes 2 hours and 1 mins to charge the Galaxy S7 Edge from 0% to 100% with OnePlus 2’s original charger that ships with their latest phone model. Check the table and chart below for details, minute by minute.

Chart 2
From the table 2, it is clear to see in the first 1 hour and a half, nearly the same time as Galaxy S7 Edge original charger time, the battery level is juiced up to 83%, and another 31 mins to be 100%. Maximum charging power is 9.5W. Compared with the Galaxy S7 Edge original charger, we note that the OnePlus 2 charger takes 27 minutes longer than the Samsung OEM model charger.

3) Tronsmart WC1T wall charger (with Quick Charge 3.0, also backwards compatible with Quick Charge 2.0 devices)
Specification: INPUT AC100-240V
OUTPUT DC:[email protected], [email protected], [email protected]

Result: Total charging time is 1 hour and a 30 minutes, almost the exact same amount of time as the Galaxy S7 Edge original charger. Charging details are below in table 3 and chart 3.

Chart 3
With 1 hour of charging, the battery level reaches to 83%, a little faster than Galaxy S7 Edge original charger. Then in the second charging stage, it takes half an hour to be 100%. Maximum charging voltage is 9.32V, current 1.58A, with a maximum of around 14.7W of power. We can see in the first charging stage, the WC1T charges rapidly and then become slow and steady in the second stage.

4) Tronsmart W2PTE wall charger (USB-A port with VoltIQ, USB-C port with Quick Charge 3.0, also backwards compatible with Quick Charge 2.0 devices)

INPUT: AC100-240V
OUTPUT1 (USB-A port): [email protected](Max)
OUTPUT2 (Type-C port): [email protected], [email protected], [email protected]
Result: Total charging time is 1 hour and 32 mins, again about the exact same charging time as the Galaxy S7 Edge original charger and WC1T wall charger. Charging details are below in table 4 and chart 4
Chart 4
In the first full hour of charging, the battery is charged to a level of 81%, then another 32 mins to be full. As we see once again, almost the exact same charging situation as our Tronsmart WC1T wall charger.

Note: As the Samsung Galaxy S7 Edge comes with a Micro-USB charging port, we use the Tronsmart CC08 USB-C to Micro-USB cable as a connection to charge the S7 with the W2PTE’s USB-C port.

5) Tronsmart C2PTE Car Charger (USB-A port with VoltIQ, USB-C port with Quick Charge 3.0, also backwards compatible with Quick Charge 2.0 devices)
Specification: INPUT DC12-24V
OUTPUT1 (USB-A port): [email protected] (Max)
OUTPUT2 (USB-C port): [email protected], [email protected], [email protected]

Result: Total of 1 hour and 33 mins to be fully charged. Charging details are below in table 5 and chart 5

Table 5
Chart 5
In the first full hour, the battery level reaches 76%, a little bit slower than the speed of the previous Tronsmart WC1t and W2PTE wall chargers. Then another 33 mins for stage 2 and to be 100% full charged.

Final Conclusion: The Quick Charge 2.0 charging technology can save approximately half an hour or so compared with the standard 5V/2A chargers on the market. And the Qualcomm-approved third-party chargers can achieve nearly identical charging times as the original Galaxy S7 Edge wall charger. If you need a car charger or a multi-port wall charger with Quick Charge 2.0, you can safely choose those third-party quick chargers to get the job done.

Source:http://www.tronsmart.com/samsung-gal...rging-analysis
The Following 21 Users Say Thank You to jisddwqs For This Useful Post: [ View ] Gift jisddwqs Ad-Free
16th April 2016, 03:18 AM |#2  
Junior Member
Flag New York
Thanks Meter: 3
 
More
Good, very interesting! If the test can add the temperature, that will be perfect
17th April 2016, 12:10 PM |#3  
Quote:
Originally Posted by Abelu

Good, very interesting! If the test can add the temperature, that will be perfect

I'd assume as the charging time are almost identical heat would be basically identical as well. P=IV so for the same period of time the heat output will be equal.
19th April 2016, 11:52 AM |#4  
OP Member
Thanks Meter: 40
 
More
Quote:
Originally Posted by randomhkkid

I'd assume as the charging time are almost identical heat would be basically identical as well. P=IV so for the same period of time the heat output will be equal.

Totally agree with your opinion
24th April 2016, 07:58 AM |#5  
dbaman's Avatar
Member
Thanks Meter: 1
 
More
very interesting and very detailed
15th May 2016, 10:06 AM |#6  
konoplya's Avatar
Senior Member
Flag Ancapistan
Thanks Meter: 19
 
More
will this charger work with my non edge S7? the amps seem to be higher than on the original fast charger supplied with it and I don't want to ruin my phone.
Attached Thumbnails
Click image for larger version

Name:	20160514_203008.jpg
Views:	612
Size:	255.5 KB
ID:	3751074  
13th June 2016, 09:22 AM |#7  
OP Member
Thanks Meter: 40
 
More
Quote:
Originally Posted by konoplya

will this charger work with my non edge S7? the amps seem to be higher than on the original fast charger supplied with it and I don't want to ruin my phone.

I suggest you to use the original chargers or the QC chargers which have Qualcomm approval.
28th March 2017, 10:44 PM |#8  
Junior Member
Thanks Meter: 1
 
More
Can you tell me what program you use to measure average charging amp? I am trying to find a program/app that lets me do that and so far I couldn't find anything. I love to use it to test my charging device. Thanks!
30th March 2017, 02:59 AM |#9  
Member
Flag Toronto
Thanks Meter: 9
 
More
Try this app - Charge Monitor for in phone monitoring of all the different parameters of your charging method.
The Following User Says Thank You to Vap0rX For This Useful Post: [ View ] Gift Vap0rX Ad-Free
6th July 2017, 01:34 PM |#10  
Junior Member
Flag Faisalabad
Thanks Meter: 0
 
More
Bro how do u check the voltage ? I used gsam battery app and when i plug in charger that came with box original fast charger it shows 938ma and 3.8 V? is this enough for fast charge?
8th July 2017, 05:48 PM |#11  
JohnLouise's Avatar
Senior Member
Gapan
Thanks Meter: 55
 
More
I bought a tronsmart cable for my s7 edge and I can say that it is a high quality cable and supports fast charge. It cost me almost 10 bucks for a pack of 3 and 6feet long.

Sent from my SM-G935F using Tapatalk

---------- Post added at 04:48 PM ---------- Previous post was at 04:47 PM ----------

Quote:
Originally Posted by ctam

Can you tell me what program you use to measure average charging amp? I am trying to find a program/app that lets me do that and so far I couldn't find anything. I love to use it to test my charging device. Thanks!

Use ampere on playstore.

Sent from my SM-G935F using Tapatalk
Post Reply Subscribe to Thread

Guest Quick Reply (no urls or BBcode)
Message:
Previous Thread Next Thread
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes