Call for Operator Settings for ALL NETWORKS

Bram87 · Apr 14, 2007

Dutch T-Mobile Internet & MMS Settings

Internet Settings:

Kies Start
Kies Settings
Kies Connections en kies Connections
Kies rechtsonder voor Advanced
Kies rechtsboven voor Select Networks
Kies bij Programs that automatically connect to the Internet should connect using voor New…
Vul bij Enter a name for these settings: in: T-Mobile Internet
Kies voor Modem
Kies voor New
De naam van het verbindingsprofiel: T-Mobile Internet
Bij Select a Modem kiest u voor Cellular line (GPRS)
Klik op Next
Er wordt gevraagd om een Access Point Name, vult u hier in: internet
U wordt nu gevraagd om een Username, Password en Domain in te vullen, u hoeft hier niets in te vullen.
Kies Advanced
Kies het tabblad TCP/IP
Kies Use server-assigned IP address
Zet alle vinkjes uit bij Software compression en IP header compression
Kies het tabblad Servers
Kies voor Use server-assigned addresses
Klik op ok
Klik op Finish

MMS Settings:

Kies Start
Kies Settings
Kies Connections en kies Connections
Kies voor de tab Advanced
Klik op Select Networks
Kies bij Programs that automatically connect to a private network should connect using voor New
Vul bij Enter a name for these settings in: T-Mobile MMS
Ga naar de tab Modem en klik op New
Vul bij Enter a name for the connection in: T-Mobile MMS
Bij Select a Modem kiest u voor Cellular line (GPRS)
Klik op Next
Vul als Access Point Name in: mms
Vul bij User name in:t-mobilemms
Vul bij Password in: t-mobilemms
Bij Domain hoeft u niets in te vullen
Klik op Finish
Klik op ok
Klik driemaal op ok en klik op het kruisje op de Settings te verlaten
Ga naar Start en kies voor Programs
Kies voor het programma MMS Composer
Klik onderaan op Tools en kies voor Options
Ga onderaan naar de tab Servers en klik op de server Default
Vul als Server Name in T-Mobile NL
Vul bij Gateway het volgende in: 010.010.010.011
Vul bij Server Address het volgende in: http://t-mobilemms
Klik op OK
Ga naar de tab Preferences
Kies bij Connect Via: voor de verbinding T-Mobile MMS
Kies bij Connect to Server: voor T-Mobile NL
Vink het hokje bij Retrieve Messages Immediately aan als u de MMS berichten direct wilt ophalen
Selecteer bij Size Limitations de waarde 100K
Kies bij No. of attempts before aborting voor de waarde 3
Vink het hokje bij Download on home network only aan indien u alleen de berichten wilt ophalen als u zich in Nederland bevindt. Dit is om de hogere GPRS Roamingkosten te besparen.
Klik op ok

diezoo · Apr 14, 2007

Movistar Argentina

Operator Connection GPRS
Operator Name & Country : Movistar - Argentina
Network Name : GPRS Movistar
Modem Name : GPRS Movistar
Modem Access Point Name : internet.gprs.unifon.com.ar
Username : wap
Password : wap
Domain :""

Operator Connection MMS
Operator Name & Country : Movistar - Argentina
Network Name : MMS Movistar
Modem Name : MMS Movistar
Modem Access Point Name : mms.gprs.unifon.com.ar
Username : mms
Password : mms
Domain :""

MMS Settings
1. Server Name : MMS Movistar
2. Gateway : 200.068.032.239
3. Port Number : 9201
4. Server Address : http://mms.tmovil.cl
5. Connect Via : MMS Movistar
6. Size Limit : 100K
7. WAP Version : 1.2

PopRocks · Apr 15, 2007

Xseries On 3 Aus.

Hi. Am running Wm6 Black v2. Is there any way to set up the ph to recieve Xseries on the 838pro. I had it b4 when running wm5. Can't seem to get it going the same way.

used reg edit
hklm\SOFTWARE\Microsoft\Windows\ CurrentVersion\Internet Settings\5.0\User Agent
and change "Default" to
DopodD810/Mozilla/4.0

Can anyone point me in the right direction. have searched wiki can't seem to find answers.

Puckster · Apr 15, 2007

PopRocks said:
Hi. Am running Wm6 Black v2. Is there any way to set up the ph to recieve Xseries on the 838pro. I had it b4 when running wm5. Can't seem to get it going the same way.

used reg edit
hklm\SOFTWARE\Microsoft\Windows\ CurrentVersion\Internet Settings\5.0\User Agent
and change "Default" to
DopodD810/Mozilla/4.0

Can anyone point me in the right direction. have searched wiki can't seem to find answers.

You cant change the actual User Agent by editing the registry any more as MS have locked this down with the settings now stored inside browser.dll in the Windows folder so OEM's can only append to the string. I just found a post on the IE Blogs site that explains why they have made the changes here: http://blogs.msdn.com/iemobile/archive/2006/08/03/Detecting_IE_Mobile.aspx. The blog doesnt mention it but it looks like it may apply to the more recent AKU's of WM5 as well as all WM6.

There is a post in the Hermes - Upgrading forum (dont have the link handy but do a search and you should find it) that explains how to hex edit the browser.dll which i have had some success with as Vodafone Live in Oz is now able to detect me as a Nokia6630 and loads some of the pages although its still not working 100% as i cant get MobileTV to work

PopRocks · Apr 15, 2007

Puckster said:
You cant change the actual User Agent by editing the registry any more as MS have locked this down with the settings now stored inside
There is a post in the Hermes - Upgrading forum (dont have the link handy but do a search and you should find it) that explains how to hex edit the browser.dll which i have had some success with as Vodafone Live in Oz is now able to detect me as a Nokia6630 and loads some of the pages although its still not working 100% as i cant get MobileTV to work

I found the link http://xdaforums.com/showthread.php?p=1184509#post1184509. Do I change the mozilla/4.0 to DopodD810/.Mozilla4.0 or some thing else?

Puckster · Apr 15, 2007

PopRocks said:
I found the link http://xdaforums.com/showthread.php?p=1184509#post1184509. Do I change the mozilla/4.0 to DopodD810/.Mozilla4.0 or some thing else?

Never used Xseries so not sure exactly how it works or what settings will work for it. I would first try changing the enties in browser.dll exactly the same as what you used to change in the registry and if that doesnt work try other variations or you may need to research it a bit more. I only found this in the last week or so myself so am still playing around with Vodafone Live as its the only user agent dependant site i have tried to get working.

Binyo · Apr 15, 2007

Hutchinson 3G 3 Network Australia Settings

Calling - Dopod 838
Messaging - Dopod D838
Camera / Imaging - Dopod D838
Internet / Planet 3 - Dopod 838
Security - Dopod 838
Bluetooth / Infrared - Dopod 838
Your PC - Dopod 838

Find out here

[[ Cold ]] · Apr 15, 2007

TIGO - COLOMBIA

WEB:
APN: web.colombiamovil.com.co
Username: ""
Password: ""
IP: 200.058.228.025
DNS: 200.058.228.025
Authentication: Normal
Compress Data: Deactivated
Compress headers: Deactivated

WAP:

APN: wap.colombiamovil.com.co
Username: ""
Password: ""
IP: 200.058.228.081
DNS: 200.058.228.081
Autentication: Normal
Compress Data: Deactivated
Compress headers: Deactivated

TIGO MMS:

APN : mms.colombiamovil.com.co / mms.tigo.com.co

Username: mms-cm1900
Password: mms-cm1900
IP: 200.058.228.081
DNS: 200.058.228.081
Autenticacion: Normal
Compress Data: Deactivated
Compress headers: Deactivated

If anyone can help me make the .cab (or make it for me

) me, and millions of users in my country will be really thankful

X_Farhad · Apr 16, 2007

Operator Connection: GPRS/EDGE
1. Operator Name & Country : MTN-Irancell - Iran
2. Network Name : Irancell-internet
3. Modem Name : Irancell-internet
4. Modem Access Point Name : mtnirancell
5. Username : ""
6. Password : ""
7. Domain : ""
8. Is there a tick in the 'This network connects to the Internet' box : Yes
9. Is there a tick in the 'This network uses a proxy server' box : Yes
10 Proxy Server Address and port :
HTTP: 10.131.26.138:8080
WAP: 10.131.26.138:9201

MMS Settings
1. Server Name : Irancell-MMS
2. Gateway : http://10.131.26.138
3. Port Number : 8080
4. Server Address : http://mms:8002
5. Connect Via : Irancell-internet
6. Size Limit : 250KB
7. WAP Version : WAP 2.0

PopRocks · Apr 16, 2007

planet 3 xseries setting

Binyo said:
Hutchinson 3G 3 Network Australia Settings

Calling - Dopod 838
Messaging - Dopod D838
Camera / Imaging - Dopod D838
Internet / Planet 3 - Dopod 838
Security - Dopod 838
Bluetooth / Infrared - Dopod 838
Your PC - Dopod 838

Find out here

There is no point going to the site you sent as they don't show you how to get it. If you ring them they ain't going to tell you.

The Dopod 838 is not even supposed to get the x series so it doesn't come in the planet three settings. you have to alter the registery to do it, which is what I did when running wm5. I upgraded to wm6 and and I need the setting to enable it again on my ph. You can't just change the registry to do it. You need to alter the .dll file first then the registry. I need the setting to change the dll too.

drooch · Apr 16, 2007

This is the easiest way to get X-series on 838pro.

Get Netfront 3.3
install
then under browser options u can change the user agent to DopodD810 and viola.... u have a Dopod D810!!!

that was so much easier than changing DLL files and u can have multiple useragents and switch between them. i have Dopod 838pro, Dopod D810 and the Nokia N73 just for fun!

Drooch

PopRocks · Apr 17, 2007

drooch said:
This is the easiest way to get X-series on 838pro.

Get Netfront 3.3
install
then under browser options u can change the user agent to DopodD810 and viola.... u have a Dopod D810!!!

that was so much easier than changing DLL files and u can have multiple useragents and switch between them. i have Dopod 838pro, Dopod D810 and the Nokia N73 just for fun!

Drooch

Thanx Muchly. Worked a treat.

X_Farhad · Apr 17, 2007

guys, how can i make a .cab file for my operator's settings ?

dan1967 · Apr 17, 2007

X_Farhad said:
guys, how can i make a .cab file for my operator's settings ?

what i did is google for wap-provisioningdoc gprs and got this
http://msdn2.microsoft.com/en-us/library/aa456052.aspx and around that area.

Further searches in the forum got me to look&browse in the other files already made; helped a lot in doing mine! credits to wpbear who lend me a hand!

It should get you to a xml file that can be tranformed into a cab.
A bit of warning: is a lot of trial&error and frustrations - took me about two weeks to make it from scratch. I am not specialist so a bit of luck is needed also. It is best to try on a fresh OS install or after a HR.
Hope it helps.

cheers,
dan

X_Farhad · Apr 18, 2007

Thanks Dan!

I just downloaded WinCE Cab manager and tried to find out what is in the cab files posted in here, almost all of them had a .xml file inside, that started with <wap-provisioningdoc> ...
but there were also many other files inside the cabs. the only "clean" one was shogun's , merely one dll file! no .xml, nothing else.

so, what do i need to include in the cab file? will the .xml file do the job? or maybe i need some special .dll file too?

Pc78 · Apr 18, 2007

I think this is possible to...the first step is to find the wright registry entries on our devices and than edit one of the operators CAB file attached in this thread....but the question is which reg files must be included in the CAB to work properly...

Regards,
Primoz

dan1967 · Apr 18, 2007

X_Farhad said:
Thanks Dan!

I just downloaded WinCE Cab manager and tried to find out what is in the cab files posted in here, almost all of them had a .xml file inside, that started with <wap-provisioningdoc> ...
but there were also many other files inside the cabs. the only "clean" one was shogun's , merely one dll file! no .xml, nothing else.

so, what do i need to include in the cab file? will the .xml file do the job? or maybe i need some special .dll file too?

I have not used any .dll
My file is this

<wap-provisioningdoc>
<characteristic type="CM_GPRSEntries">
<characteristic type="Vodafone">
<parm name="DestId" value="{436EF144-B4FB-4863-A041-8F905A62C572}" />
<parm name="UserName" value="internet.vodafone.ro" />
<parm name="Password" value="vodafone" />
<parm name="SwCompression" value="1" />
<parm name="IpHeaderCompression" value="0" />
<parm name="SpecificNameServers" value="1" />
<parm name="DnsAddr" value="193.230.161.3" />
<parm name="AltDnsAddr" value="193.230.161.4" />
<parm name="Domain" value="" />
<characteristic type="DevSpecificCellular">
<parm name="GPRSInfoValid" value="1" />
<parm name="GPRSInfoAccessPointName" value="internet.vodafone.ro" />
<parm name="BearerInfoValid" value="1" />
<parm name="GPRSInfoProtocolType" value="2" />
<parm name="GPRSInfoL2ProtocolType" value="PPP" />
<parm name="GPRSInfoAddress" value="" />
<parm name="GPRSInfoDataCompression" value="1" />
<parm name="GPRSInfoHeaderCompression" value="1" />
<parm name="GPRSInfoParameters" value="" />
</characteristic>
</characteristic>
</characteristic>

<characteristic type="Registry">
<characteristic type="HKCU\ControlPanel\PhoneExtendFunction" translation="filesystem">
<parm name="GPRSAuthenticationMethod" datatype="integer" value="1" />

</characteristic>
</characteristic>
</wap-provisioningdoc>

There is only one registry entry that I needed; took it out just by fishing in the files. You can try editing this file with your data and see the outcome.

cheers,
dan

walshieau · Apr 18, 2007

AND HERE IT IS!!!!

...........

y2whisper · Apr 18, 2007

This a repost from runny I am reposting it as it seems to have been missed, will edit if need be:

Rogers CANADA

GPRS Settings

1. Operator Name & Country : Rogers Canada
2. Network Name : MY ISP
(Name in the Connections Tab)
3. Modem Name :ROGERS GPRS
4. Modem Access Point Name :internet.com
5. Username :wapuser1
6. Password :wap
7. Domain :””
8. Is there a tick in the 'This network connects to the Internet' box :
NO
9. Is there a tick in the 'This network uses a proxy server' box :
NO

MMS Settings

2. Network Name : MY Work Settings
(Name in the Connections Tab)
3. Modem Name :ROGERS MMS
4. Modem Access Point Name :media.com
5. Username :media
6. Password :mda01
7. Domain :””
8. Is there a tick in the 'This network connects to the Internet' box :
NO
9. Is there a tick in the 'This network uses a proxy server' box :
NO

1. Server Name :Rogers MMS
2. Gateway :172.25.0.107
3. Port Number : 8080
4. Server Address : http://mms.gprs.rogers.com
5. Connect Via : My Work settings
6. Size Limit : 300
7. WAP Version : 2.0

blurnard · Apr 19, 2007

How to use it

Hi guys..

I am really noob here...

I had upgrade the 838pro to WM6 and my gprs/mms settings are all gone.
Can anyone direct me on how to enter the settings into my phone?

Call for Operator Settings for ALL NETWORKS

Senior Member

Senior Member

Member

Senior Member

Member

Senior Member

Member

Inactive Recognized Developer

Senior Member

Member

Member

Member

Senior Member

Senior Member

Senior Member

Senior Member

Senior Member

Senior Member

Senior Member

Member

Similar threads