can u put ur phone in downloading/emergency mode try that
Sent from my LG-P500 using XDA
[HOWTO][PICTURE GUIDE]Update your firmware using KDZ Updater
- Thread starter nikhil4186
- Start date
can u put ur phone in downloading/emergency mode try that
Sent from my LG-P500 using XDA
> can I do this flashing over KDZ , cause I'm on ICS right now.. Some one told me before that flashing back to original stock firmware would solved this BUG for me.. my phone do have this problem.. when I press something on the screen.. it goes wild and press at different parts.. like whe i press "S" it presses "Q" instead 
.. this happens sometimes to me.. not all the time.. its just bugging me.. and want to solved it today
.. this happens sometimes to me.. not all the time.. its just bugging me.. and want to solved it today i just got ordered and P500 from ebay, it was locked on three uk and i had it unlocked by imei at a local shop for 3 euros
it was running 2.2 stock and i updated it to 2.2.2 with the lg suport tool .. there was no more updates to 2.3.3 so i decide to do it manualy
i followed the exact steps from here .. lg pc suite never recognized the phone so i installed the drivers package from lg.com .. i used v20g open europe and it flashed ok
it was running 2.2 stock and i updated it to 2.2.2 with the lg suport tool .. there was no more updates to 2.3.3 so i decide to do it manualy
i followed the exact steps from here .. lg pc suite never recognized the phone so i installed the drivers package from lg.com .. i used v20g open europe and it flashed ok
good work
good work i did it also if my phone is lg c660 , my phone scared me cause when i finished flashing and i switched the device stopped on the logo screen i flashed again and again 4 times and while i was reading the comments here in the thread i found a small information from the member TERRATRIX to do a HARD RESET using POWER + VOL DOWN + HOME buttons holding them in the same time , i did and i got a hard reset and the phone entered to the home screen and now i have my phone back on the original software .
thanks developers you are great :laugh:
good work i did it also if my phone is lg c660 , my phone scared me cause when i finished flashing and i switched the device stopped on the logo screen i flashed again and again 4 times and while i was reading the comments here in the thread i found a small information from the member TERRATRIX to do a HARD RESET using POWER + VOL DOWN + HOME buttons holding them in the same time , i did and i got a hard reset and the phone entered to the home screen and now i have my phone back on the original software .
thanks developers you are great :laugh:
Pretty sure ive bricked my phone
was getting the dll msg error when it disconnected
When I try and get into download mode now all I get the the following screen and I cant boot the phone
Please HELP
Thank you !!!
EDIT: Now im back in download mode again , dunno how , but now i'll try and flash again .
---------- Post added at 02:18 PM ---------- Previous post was at 01:58 PM ----------
Now I get this error when trying to flash
was getting the dll msg error when it disconnected
When I try and get into download mode now all I get the the following screen and I cant boot the phone
Please HELP
Thank you !!!
EDIT: Now im back in download mode again , dunno how , but now i'll try and flash again .
---------- Post added at 02:18 PM ---------- Previous post was at 01:58 PM ----------
Pretty sure ive bricked my phone
was getting the dll msg error when it disconnected
When I try and get into download mode now all I get the the following screen and I cant boot the phone
Please HELP
Thank you !!!
EDIT: Now im back in download mode again , dunno how , but now i'll try and flash again .
Now I get this error when trying to flash
Last edited:
Lg official firmware link is not working on.
Please update now.
Today I have bricked my one and only lg p500 while messing with su binaries .
I am moving to recovery directly and cannot boot , even problem is not this but i my amonra thunder g recovery in not opening .????????
Please update now.
Today I have bricked my one and only lg p500 while messing with su binaries .
I am moving to recovery directly and cannot boot , even problem is not this but i my amonra thunder g recovery in not opening .????????
Similar threads
- Poll
Top Liked Posts
-
There are no posts matching your filters.
-
66Since most of all are newbs and don't want to get into all the android jargon I created a small tutorial from all the existing ones.
Q: What is this tutorial meant to do?
A: Help you to update/flash official firmware on your phone [helpful for those with slow or no internet connection]
So first off all you need to download the following files.
KDZ updater
LG official firmware android version v2.2.2 build v10E created by VIjayKumar
A major part of the procedure is created by victortangocharlie, rest edited by me (pictures etc)
victortangocharlie and edited by nikhil4186 said:Procedure to install original firmware using KDZ-FW-UPD.exe ( KDZ FIRMWARE UPDATER )
[Note: This procedure was used to install V10E_00.kdz(android2.2.2) over V10b_00.kdz(android2.2) on an unbranded Indian GSM model of LG P500 using a Windows xp 32bit service pack 3.]
1. Install LG PC Suite IV from SD card which came with phone by connecting the phone to PC through USB cable. This is done to install the drivers for the phone on the PC (the procedure is as follows)
- Enable the 'USB Mass Storage Only' mode in the phone's Settings/SDcard & Phone Storage menu.
- Connect phone to PC with the USB Cable.
- Press the 'Turn on USB Storage' button which appears on phone.
- Browse to the folder containing the 'LG PC Suite IV' on the phone's SD card using Windows Explorer and run the LG Installer file. PC Suite will now install on your system along with the required drivers for your phone.
- Cancel setting up PC Suite or continue setting up PC Suite if you want to Sync or backup the phone data.
- After closing PC Suite, Safely remove the USB device from your system.
- Press the 'Turn off USB Storage' button on phone screen.
- Detach the USB Cable.
- Disable the 'USB Mass Storage Only' mode in the phone's Settings/SDcard &Phone Storage menu.
2. Remove the screen lock
3. Charge the phone to the maximum.
4. Enable USB Debugging on Phone (Settings/Applications/Development).
5. Detach all other peripherals from your PC. Exit all running applications on your PC especially other PC suites if any. Also exit running programs from the notification bar on the desktop. (Also uninstall Nokia or other phone drivers & microsoft visual ++ runtime environments - not an essential step.)
6.[IMPORTANT] Disable 'LGE Virtual Modem' in PC's Device Manager. (In your Windows operating system, go to Control Panel > System > Hardware > Device Manager > Modems > Right click on LGE Virtual Modem and click Disable.)
If this step is not followed the Phone will get bricked!
7. Move all the apps from the SD Card to phone memory and then Unmount the SD card from the phone (Settings/SDcard & Phone Storage) so as to remove it (physically) from the phone.
8. Open the phones back cover and remove the SD Card.
9. Download KDZ_FW_UPD_EN.7z onto your PC and extract it to a folder. Available HERE.Direct Download Link. (MD5 of 7zip file - 813A28BE9182AB604A1D43E745CE7AD7)
10. Run the msxml.msi file and complete the installation.
11. Connect the phone to PC with USB Cable.( If you are using a desktop PC, make sure you use USB ports that are in the back of your PC, avoid the front ports.)
12. Run KDZ_FW_UPD.exe from the extracted folder.
13. Chose TYPE as 3GQCT & Phone Mode as DIAG.
14. In the 'KDZ file' space, browse for the firmware you want to install. (In this case V10E_00.kdz)
15. Press the 'Launch software update' button.
16. The firmware flashing process is now underway.
If all goes well, in 5-10 minutes the phone will be flashed with the new firmware.
I shall describe in detail what happened with my phone - 10-15 seconds after launching software update on PC, my phone screen turned blank and in a couple of seconds the phone entered the 'Emergency Mode'. During this mode the screen was yellow with Emergency Mode written along the middle of the screen. Also you can check the progress on your computer in the KDZ updater. I have attached a text log file for you to compare. When the update is finished the KDZ updater will show a message in the log screen itself as =FINISHED=. The phone stays the same way till the Software update procedure finished on the pc and the phone turnes blank in the end. I waited a while for it to reboot but after a minute or so, I manually switched on the phone. The phone came alive and following the LG boot animation, the android logo screen came up. The phone takes about 2 or more whole minutes in that state before booting up fully and entering the home screen.
17. After booting up fully, detach the phone from the pc.
Go to 'About Phone' in Settings and confirm the change from 2.2 to v2.2.2
I have attached my LOG file so you acn compare it with yours.
After the update all the settings etc etc were the same. I also did not back up my phone.
Additional Links Rooting, Installing - Android SDK, Custom Recovery, Custom ROM's tutorial by victortangocharlie2Please notify me if you see any errors in this tutorial or if you have something to add to this.1
now that you said it, I sure will. just need a little time to read edit and create the photos. another fact that I don't have a computer adds to the challenge lol. tutorials already exist but pictures are better aren't they1
Although KDZ is meant for LG phones, i am not sure whether it would work with optimus 2x.1thanxxx buddy...now i will update it asap after i buy it next month..
damn, you don't even have the phone! what was the nagging all about? lol
