[18/06/2012][ROM]photonic CM 7.2 - 2.6.35

Search This thread
By:
Advanced…
O

osmarsilva

Member
Apr 4, 2012
12
2
Please Help me Wifi Doesn't Work

hi guys, my wifi doesn't work on the nand I tried install CM7 2.3, 2.2, When I active the wifi I can see error and wifi doesn't activated.

I downloaded a android HTC SENSE 3.5 in the forum and wifi works and I run android from my sd card wifi works fine.

I tried install two bootloader lk-photonic.nb and out.nb.


Please Help me.

tks a lot.
 
jomaga

jomaga

Senior Member
Apr 20, 2008
869
1,257
Hi Schlund
I´m searching a bit about the audio headset issue, and running a logcat from DDMS, I noticed when I plug or unplug my headset allways there's a line like this:

04-18 22:38:34.063: W/Vold(118): Ignoring unknown switch 'Headset'

Could it be related to it? the system could be still in mono state from the phone speaker?

The full log related to plugging the headset is:
04-18 22:38:34.063: V/HeadsetObserver(183): Headset UEVENT: {SUBSYSTEM=switch, SWITCH_STATE=130, DEVPATH=/devices/virtual/switch/h2w, SEQNUM=2028, ACTION=change, SWITCH_NAME=Headset}
04-18 22:38:34.063: W/Vold(118): Ignoring unknown switch 'Headset'
04-18 22:38:34.063: V/HeadsetObserver(183): Intent.ACTION_HEADSET_PLUG: state: 1 name: Headset mic: 0

Any clue?

Still searching....
 
Last edited:
  • Like
Reactions: tm.bax and schlund
S

swissly

Senior Member
Jul 10, 2008
138
20
Schlund,

Today I found out something about the bluetooth problem, I don't know if this will be of help. I tried two different devices:

- the first is a bluetooth audio receiver (supports A2DP): I can pair with this, connect to it and music plays well without any problems!
- the second is my car (does not support A2DP): I can pair with it but connecting does not work.

Is there anything I could check on the device which does not even connect?

And then I found another issue with the wired headset. It does work for phonecalls without problems. But when I finish the call music starts playing!?! (music was not playing before). This only happens when using the headset. Is this a bug of CM or something specific on this build?

Thanks
 
S

schlund

Senior Member
Nov 25, 2010
457
1,064
jomaga said:
Hi Schlund
I´m searching a bit about the audio headset issue, and running a logcat from DDMS, I noticed when I plug or unplug my headset allways there's a line like this:

04-18 22:38:34.063: W/Vold(118): Ignoring unknown switch 'Headset'

Could it be related to it? the system could be still in mono state from the phone speaker?

The full log related to plugging the headset is:
04-18 22:38:34.063: V/HeadsetObserver(183): Headset UEVENT: {SUBSYSTEM=switch, SWITCH_STATE=130, DEVPATH=/devices/virtual/switch/h2w, SEQNUM=2028, ACTION=change, SWITCH_NAME=Headset}
04-18 22:38:34.063: W/Vold(118): Ignoring unknown switch 'Headset'
04-18 22:38:34.063: V/HeadsetObserver(183): Intent.ACTION_HEADSET_PLUG: state: 1 name: Headset mic: 0

Any clue?

Still searching....
Click to expand...
Click to collapse

I am happy to see others searching for the problem:)
i checked this part of code in android, the function that puts that error message out is only about usb devices, thats why its igoring "Headset" :(
 
  • Like
Reactions: Vogelhaus7, jomaga, ToughGuy and 1 other person
S

schlund

Senior Member
Nov 25, 2010
457
1,064
swissly said:
Schlund,

Today I found out something about the bluetooth problem, I don't know if this will be of help. I tried two different devices:

- the first is a bluetooth audio receiver (supports A2DP): I can pair with this, connect to it and music plays well without any problems!
- the second is my car (does not support A2DP): I can pair with it but connecting does not work.

Is there anything I could check on the device which does not even connect?

And then I found another issue with the wired headset. It does work for phonecalls without problems. But when I finish the call music starts playing!?! (music was not playing before). This only happens when using the headset. Is this a bug of CM or something specific on this build?

Thanks
Click to expand...
Click to collapse

pairing with cars is always special :)
yes i know bout the headset play problem (is because of the button) but as far as i know derefas has fixed it.
 
  • Like
Reactions: ToughGuy and tm.bax
jomaga

jomaga

Senior Member
Apr 20, 2008
869
1,257
I found an 35mm jack driver from HTC. I'm not sure if it's useful for mono/stereo issue, but anyway here it is:
http://gitorious.org/linux-on-wince...lobs/master/arch/arm/mach-msm/htc_35mm_jack.c

---------- Post added at 10:45 PM ---------- Previous post was at 09:59 PM ----------

Here is my full log after reboot concerning Libacoustic and AudioHardware lines:
Code: 
04-20 00:03:12.509: V/Libacoustic-wince(123): Running custom built libhtc_acoustic.so
04-20 00:03:12.509: V/Libacoustic-wince(123): Device capabilities :
04-20 00:03:12.509: V/Libacoustic-wince(123): - Htc voc cal fields per params : 17
04-20 00:03:12.509: V/Libacoustic-wince(123): - Dual mic supported : false
04-20 00:03:12.509: E/Libacoustic-wince(123): Error opening dev /dev/tpa2016d2 (fd = 9). Error No such file or directory (2)
04-20 00:03:12.509: V/Libacoustic-wince(123): - Use TPA2016 Amplifier : false
04-20 00:03:12.509: E/Libacoustic-wince(123): Failed to open /sdcard/AudioPara3.csv. Error Permission denied (13)
04-20 00:03:12.509: E/Libacoustic-wince(123): Trying with default file
04-20 00:03:12.509: E/Libacoustic-wince(123): Successfully opened /system/etc/AudioPara3.csv
04-20 00:03:12.539: V/Libacoustic-wince(123): BT Phone Acoustic Table: Default
04-20 00:03:12.539: V/Libacoustic-wince(123): BT Phone Acoustic Table: HTC BH S100
04-20 00:03:12.539: V/Libacoustic-wince(123): BT Phone Acoustic Table: HTC BH M100
04-20 00:03:12.539: V/Libacoustic-wince(123): BT Phone Acoustic Table: Motorola H500
04-20 00:03:12.539: V/Libacoustic-wince(123): BT Phone Acoustic Table: Nokia HS-36W
04-20 00:03:12.539: V/Libacoustic-wince(123): BT Phone Acoustic Table: PLT 510v.D
04-20 00:03:12.539: V/Libacoustic-wince(123): BT Phone Acoustic Table: M2500 by Plantronics
04-20 00:03:12.539: V/Libacoustic-wince(123): BT Phone Acoustic Table: Nokia HDW-3
04-20 00:03:12.539: V/Libacoustic-wince(123): BT Phone Acoustic Table: HBH-608
04-20 00:03:12.539: V/Libacoustic-wince(123): BT Phone Acoustic Table: HBH-DS970
04-20 00:03:12.539: V/Libacoustic-wince(123): BT Phone Acoustic Table: i.Tech BlueBAND
04-20 00:03:12.539: V/Libacoustic-wince(123): BT Phone Acoustic Table: Nokia BH-800
04-20 00:03:12.539: V/Libacoustic-wince(123): BT Phone Acoustic Table: Motorola H700
04-20 00:03:12.539: V/Libacoustic-wince(123): BT Phone Acoustic Table: HTC BH M200
04-20 00:03:12.549: V/Libacoustic-wince(123): BT Phone Acoustic Table: Jabra JX10
04-20 00:03:12.549: V/Libacoustic-wince(123): BT Phone Acoustic Table: 320Plantronics
04-20 00:03:12.549: V/Libacoustic-wince(123): BT Phone Acoustic Table: 640Plantronics
04-20 00:03:12.549: V/Libacoustic-wince(123): BT Phone Acoustic Table: Jabra BT500
04-20 00:03:12.549: V/Libacoustic-wince(123): BT Phone Acoustic Table: Motorola HT820
04-20 00:03:12.549: V/Libacoustic-wince(123): BT Phone Acoustic Table: HBH-IV840
04-20 00:03:12.549: V/Libacoustic-wince(123): BT Phone Acoustic Table: 6XXPlantronics
04-20 00:03:12.549: V/Libacoustic-wince(123): BT Phone Acoustic Table: 3xxPlantronics
04-20 00:03:12.549: V/Libacoustic-wince(123): BT Phone Acoustic Table: HBH-PV710
04-20 00:03:12.549: V/Libacoustic-wince(123): BT Phone Acoustic Table: Motorola H670
04-20 00:03:12.549: V/Libacoustic-wince(123): BT Phone Acoustic Table: HBM-300
04-20 00:03:12.549: V/Libacoustic-wince(123): BT Phone Acoustic Table: Nokia BH-208
04-20 00:03:12.549: V/Libacoustic-wince(123): BT Phone Acoustic Table: Samsung WEP410
04-20 00:03:12.549: V/Libacoustic-wince(123): BT Phone Acoustic Table: Jabra BT8010
04-20 00:03:12.549: V/Libacoustic-wince(123): BT Phone Acoustic Table: Motorola S9
04-20 00:03:12.549: V/Libacoustic-wince(123): BT Phone Acoustic Table: Jabra BT620s
04-20 00:03:12.549: V/Libacoustic-wince(123): BT Phone Acoustic Table: Nokia BH-902
04-20 00:03:12.549: V/Libacoustic-wince(123): BT Phone Acoustic Table: HBH-DS220
04-20 00:03:12.549: V/Libacoustic-wince(123): BT Phone Acoustic Table: HBH-DS980
04-20 00:03:12.549: V/Libacoustic-wince(123): BT Phone Acoustic Table: 8XXPlantronics
04-20 00:03:12.549: V/Libacoustic-wince(123): BT Phone Acoustic Table: Palm Headset
04-20 00:03:12.559: V/Libacoustic-wince(123): BT Phone Acoustic Table: Jawbone
04-20 00:03:12.559: V/Libacoustic-wince(123): BT Phone Acoustic Table: Jawbone1234
04-20 00:03:12.559: V/Libacoustic-wince(123): BT Phone Acoustic Table: 590Plantronics
04-20 00:03:12.559: V/Libacoustic-wince(123): BT Phone Acoustic Table: Audi UHV 6384
04-20 00:03:12.559: V/Libacoustic-wince(123): BT Phone Acoustic Table: BlueConnect(tm)
04-20 00:03:12.559: V/Libacoustic-wince(123): BT Phone Acoustic Table: HandsFreeLink TM
04-20 00:03:12.559: V/Libacoustic-wince(123): BT Phone Acoustic Table: Parrot 3400LS
04-20 00:03:12.559: V/Libacoustic-wince(123): BT Phone Acoustic Table: BMW
04-20 00:03:12.559: V/Libacoustic-wince(123): BT Phone Acoustic Table: Motorola H350
04-20 00:03:12.559: V/Libacoustic-wince(123): BT Phone Acoustic Table: Jabra BT135
04-20 00:03:12.559: V/Libacoustic-wince(123): BT Phone Acoustic Table: Jabra BT160
04-20 00:03:12.559: V/Libacoustic-wince(123): BT Phone Acoustic Table: Motorola H721
04-20 00:03:12.559: V/Libacoustic-wince(123): BT Phone Acoustic Table: DoCoMo Wireless P01
04-20 00:03:12.559: V/Libacoustic-wince(123): BT Phone Acoustic Table: SoundLeaf+
04-20 00:03:12.559: V/Libacoustic-wince(123): BT Phone Acoustic Table: Nokia BH-103
04-20 00:03:12.559: V/Libacoustic-wince(123): BT Phone Acoustic Table: Jabra BT530
04-20 00:03:12.559: V/Libacoustic-wince(123): BT Phone Acoustic Table: Jabra BT3030
04-20 00:03:12.559: V/Libacoustic-wince(123): BT Phone Acoustic Table: JKDAP3265
04-20 00:03:12.559: V/Libacoustic-wince(123): BT Phone Acoustic Table: JKDAP3264
04-20 00:03:12.559: V/Libacoustic-wince(123): BT Phone Acoustic Table: Jabra BT5010
04-20 00:03:12.559: V/Libacoustic-wince(123): BT Phone Acoustic Table: Motorola H12
04-20 00:03:12.559: V/Libacoustic-wince(123): BT Phone Acoustic Table: Nokia BH-703
04-20 00:03:12.569: V/Libacoustic-wince(123): BT Phone Acoustic Table: Motorola H710
04-20 00:03:12.569: V/Libacoustic-wince(123): BT Phone Acoustic Table: Jabra BT2050
04-20 00:03:12.569: V/Libacoustic-wince(123): BT Phone Acoustic Table: Jabra BT2070
04-20 00:03:12.569: V/Libacoustic-wince(123): BT Phone Acoustic Table: Bluetooth headset
04-20 00:03:12.569: V/Libacoustic-wince(123): BT Phone Acoustic Table: i.Air 301
04-20 00:03:12.569: V/Libacoustic-wince(123): BT Phone Acoustic Table: BH M300
04-20 00:03:12.569: V/Libacoustic-wince(123): BT Phone Acoustic Table: Clip Music 801
04-20 00:03:12.569: V/Libacoustic-wince(123): BT Phone Acoustic Table: Clip Naro 601
04-20 00:03:12.569: V/Libacoustic-wince(123): BT Phone Acoustic Table: Jabra BT8040
04-20 00:03:12.589: I/Libacoustic-wince(123): Readed :
04-20 00:03:12.589: I/Libacoustic-wince(123): 24 Audio_Path_Table entries
04-20 00:03:12.589: I/Libacoustic-wince(123): 24 Audio_Path_Uplink_Table entries
04-20 00:03:12.589: I/Libacoustic-wince(123): 36 Phone_Acoustic_Table entries
04-20 00:03:12.589: I/Libacoustic-wince(123): 36 WB_Phone_Acoustic_Table entries
04-20 00:03:12.589: I/Libacoustic-wince(123): 66 BT_Phone_Acoustic_Table entries
04-20 00:03:12.589: I/Libacoustic-wince(123): 24 HTC_VOC_CAL_CODEC_TABLE_Table entries
04-20 00:03:12.589: I/Libacoustic-wince(123): 13 CE_Acoustic_Table entries
04-20 00:03:12.589: V/Libacoustic-wince(123): UpdateAudioAdieTable(bAudioUplinkReq 0,bAUXBypassReq 0, bEnableHSSD=0, bForceUpdate = 1)
04-20 00:03:12.599: I/Libacoustic-wince(123): get_audpp_filter
04-20 00:03:12.599: E/Libacoustic-wince(123): Failed to open AUDIO_NORMAL_FILTER /sdcard/AudioFilterTable.csv. Error Permission denied (13)
04-20 00:03:12.599: E/Libacoustic-wince(123): Trying with default file
04-20 00:03:12.599: E/Libacoustic-wince(123): Successfully opened /system/etc/AudioFilterTable.csv
04-20 00:03:12.599: V/Libacoustic-wince(123): Found IIR filter
04-20 00:03:12.599: V/Libacoustic-wince(123): Found ADRC record
04-20 00:03:12.599: V/Libacoustic-wince(123): Found EQ record
04-20 00:03:12.599: I/Libacoustic-wince(123): EQ flag = ffff.
04-20 00:03:12.599: I/Libacoustic-wince(123): EQ_GAIN=00. EQ_FREQ=190. EQ_TYPE=01. EQ_QF=16a.
04-20 00:03:12.599: I/Libacoustic-wince(123): EQ_GAIN=03. EQ_FREQ=1f4. EQ_TYPE=03. EQ_QF=16a.
04-20 00:03:12.599: I/Libacoustic-wince(123): EQ_GAIN=01. EQ_FREQ=3b6. EQ_TYPE=03. EQ_QF=16a.
04-20 00:03:12.599: I/Libacoustic-wince(123): EQ_GAIN=02. EQ_FREQ=6a4. EQ_TYPE=03. EQ_QF=16a.
04-20 00:03:12.599: I/Libacoustic-wince(123): EQ_GAIN=00. EQ_FREQ=1388. EQ_TYPE=03. EQ_QF=16a.
04-20 00:03:12.599: I/Libacoustic-wince(123): EQ_GAIN=00. EQ_FREQ=1f40. EQ_TYPE=03. EQ_QF=16a.
04-20 00:03:12.599: I/Libacoustic-wince(123): EQ_GAIN=00. EQ_FREQ=2328. EQ_TYPE=03. EQ_QF=16a.
04-20 00:03:12.599: I/Libacoustic-wince(123): EQ_GAIN=00. EQ_FREQ=4650. EQ_TYPE=02. EQ_QF=16a.
04-20 00:03:12.599: I/Libacoustic-wince(123): get_audpre_table
04-20 00:03:12.599: E/Libacoustic-wince(123): Failed to open AUDIO_NORMAL_PREPROCESS /sdcard/AudioPreProcessTable.csv. Error Permission denied (13)
04-20 00:03:12.599: E/Libacoustic-wince(123): Trying with default file
04-20 00:03:12.609: E/Libacoustic-wince(123): Successfully opened /system/etc/AudioPreProcessTable.csv
04-20 00:03:12.609: V/Libacoustic-wince(123): Found TX_IIR filter 0
04-20 00:03:12.609: V/Libacoustic-wince(123): Found TX_IIR filter 1
04-20 00:03:12.609: V/Libacoustic-wince(123): Found TX_IIR filter 2
04-20 00:03:12.609: V/Libacoustic-wince(123): Found TX_IIR filter 3
04-20 00:03:12.609: V/Libacoustic-wince(123): Found TX_IIR filter 4
04-20 00:03:12.609: V/Libacoustic-wince(123): Found TX_IIR filter 5
04-20 00:03:12.609: V/Libacoustic-wince(123): Found TX_IIR filter 6
04-20 00:03:12.609: V/Libacoustic-wince(123): Found TX_IIR filter 7
04-20 00:03:12.609: V/Libacoustic-wince(123): Found TX_IIR filter 8
04-20 00:03:12.609: V/Libacoustic-wince(123): Found TX_IIR filter 9
04-20 00:03:12.609: V/Libacoustic-wince(123): Found TX_IIR filter 10
04-20 00:03:12.609: V/Libacoustic-wince(123): Found TX_IIR filter 11
04-20 00:03:12.609: V/Libacoustic-wince(123): Found TX_IIR filter 12
04-20 00:03:12.609: V/Libacoustic-wince(123): Found TX_IIR filter 13
04-20 00:03:12.609: V/Libacoustic-wince(123): Found TX_IIR filter 14
04-20 00:03:12.609: V/Libacoustic-wince(123): Found TX_IIR filter 15
04-20 00:03:12.609: V/Libacoustic-wince(123): Found TX_IIR filter 16
04-20 00:03:12.609: V/Libacoustic-wince(123): Found TX_IIR filter 17
04-20 00:03:12.609: V/Libacoustic-wince(123): Found AGC filter 0
04-20 00:03:12.609: V/Libacoustic-wince(123): Found AGC filter 1
04-20 00:03:12.609: V/Libacoustic-wince(123): Found AGC filter 2
04-20 00:03:12.609: V/Libacoustic-wince(123): Found AGC filter 3
04-20 00:03:12.609: V/Libacoustic-wince(123): Found AGC filter 4
04-20 00:03:12.609: V/Libacoustic-wince(123): Found AGC filter 5
04-20 00:03:12.609: V/Libacoustic-wince(123): Found AGC filter 6
04-20 00:03:12.609: V/Libacoustic-wince(123): Found AGC filter 7
04-20 00:03:12.609: V/Libacoustic-wince(123): Found AGC filter 8
04-20 00:03:12.609: V/Libacoustic-wince(123): Found NS record 0
04-20 00:03:12.609: V/Libacoustic-wince(123): Found NS record 1
04-20 00:03:12.609: V/Libacoustic-wince(123): Found NS record 2
04-20 00:03:12.609: V/Libacoustic-wince(123): Found NS record 3
04-20 00:03:12.609: V/Libacoustic-wince(123): Found NS record 4
04-20 00:03:12.609: V/Libacoustic-wince(123): Found NS record 5
04-20 00:03:12.609: V/Libacoustic-wince(123): Found NS record 6
04-20 00:03:12.609: V/Libacoustic-wince(123): Found NS record 7
04-20 00:03:12.609: V/Libacoustic-wince(123): Found NS record 8
04-20 00:03:12.609: V/Libacoustic-wince(123): constructed (9 SND endpoints)
04-20 00:03:12.609: V/Libacoustic-wince(123): cnt = 0 ept->name = HANDSET ept->id = 0
04-20 00:03:12.609: V/Libacoustic-wince(123): cnt = 1 ept->name = SPEAKER ept->id = 1
04-20 00:03:12.609: V/Libacoustic-wince(123): cnt = 2 ept->name = HEADSET ept->id = 2
04-20 00:03:12.609: V/Libacoustic-wince(123): cnt = 3 ept->name = NO_MIC_HEADSET ept->id = 2
04-20 00:03:12.609: V/Libacoustic-wince(123): cnt = 4 ept->name = BT ept->id = 3
04-20 00:03:12.609: V/Libacoustic-wince(123): cnt = 5 ept->name = BT_EC_OFF ept->id = 3
04-20 00:03:12.609: V/Libacoustic-wince(123): cnt = 6 ept->name = SPEAKER_MIC ept->id = 13
04-20 00:03:12.609: V/Libacoustic-wince(123): cnt = 7 ept->name = IDLE ept->id = 17
04-20 00:03:12.609: V/Libacoustic-wince(123): cnt = 8 ept->name = CURRENT ept->id = 256
04-20 00:03:12.609: E/AudioHardwareMSM72XX_wince(123): Error opening dev /dev/audience_A1010 (fd = -1). Error No such file or directory (2)
04-20 00:03:12.609: D/AudioHardwareMSM72XX_wince(123): mNumSndEndpoints = 9
04-20 00:03:12.609: V/AudioHardwareMSM72XX_wince(123): constructed 9 SND endpoints
04-20 00:03:12.609: V/AudioHardwareMSM72XX_wince(123): cnt = 0 ept->name = HANDSET ept->id = 0
04-20 00:03:12.609: V/AudioHardwareMSM72XX_wince(123): cnt = 1 ept->name = SPEAKER ept->id = 1
04-20 00:03:12.609: V/AudioHardwareMSM72XX_wince(123): cnt = 2 ept->name = HEADSET ept->id = 2
04-20 00:03:12.609: V/AudioHardwareMSM72XX_wince(123): cnt = 3 ept->name = NO_MIC_HEADSET ept->id = 2
04-20 00:03:12.609: V/AudioHardwareMSM72XX_wince(123): cnt = 4 ept->name = BT ept->id = 3
04-20 00:03:12.609: V/AudioHardwareMSM72XX_wince(123): cnt = 5 ept->name = BT_EC_OFF ept->id = 3
04-20 00:03:12.609: V/AudioHardwareMSM72XX_wince(123): cnt = 6 ept->name = SPEAKER_MIC ept->id = 13
04-20 00:03:12.609: V/AudioHardwareMSM72XX_wince(123): cnt = 7 ept->name = IDLE ept->id = 17
04-20 00:03:12.609: V/AudioHardwareMSM72XX_wince(123): cnt = 8 ept->name = CURRENT ept->id = 256
04-20 00:03:12.609: V/AudioHardwareMSM72XX_wince(123): doAcousticVolumeUpdate 17 1 5
04-20 00:03:12.609: D/AudioHardwareMSM72XX_wince(123): rpc snd_set_volume(17, 1, 5)
04-20 00:03:12.609: V/AudioHardwareMSM72XX_wince(123): Initial audio volume setting done
04-20 00:03:12.609: V/AudioHardwareMSM72XX_wince(123): AudioHardware::AudioHardware Initialized
04-20 00:03:12.619: D/AudioHardwareInterface(123): setMode(NORMAL)
04-20 00:03:12.619: I/AudioHardwareMSM72XX_wince(123): Set master volume to 5.
04-20 00:03:12.629: I/CameraService(123): CameraService started (pid=123)
04-20 00:03:12.639: D/AudioFlinger(123): setParameters(): io 1, keyvalue routing=2, tid 157, calling tid 123
04-20 00:03:12.639: I/AudioFlinger(123): AudioFlinger's thread 0x30fb8 ready to run
04-20 00:03:12.639: V/AudioHardwareMSM72XX_wince(123): AudioStreamOutMSM72xx::setParameters() routing=2
04-20 00:03:12.639: V/AudioHardwareMSM72XX_wince(123): set output routing 2
04-20 00:03:12.639: I/AudioHardwareMSM72XX_wince(123): Routing audio to Speakerphone
04-20 00:03:12.639: V/AudioHardwareMSM72XX_wince(123): doAudioRouteOrMute() device 1, mMode 0, mMicMute 1
04-20 00:03:12.639: V/AudioHardwareMSM72XX_wince(123): AudioHardware::update_device 1 1 1
04-20 00:03:12.639: V/Libacoustic-wince(123): msm72xx_start_acoustic_setting
04-20 00:03:12.639: V/Libacoustic-wince(123): msm72xx_set_audio_path: device=1 Mic = 0, DualMic = 0, Speaker = 0, Headset = 0
04-20 00:03:12.639: V/Libacoustic-wince(123): UpdateAudioAdieTable(bAudioUplinkReq 0,bAUXBypassReq 0, bEnableHSSD=0, bForceUpdate = 0)
04-20 00:03:12.639: V/Libacoustic-wince(123): Update not required
04-20 00:03:12.679: V/Libacoustic-wince(123): msm72xx_set_acoustic_table 1 5
04-20 00:03:12.679: V/Libacoustic-wince(123): Acoustic profile : HANDSFREE
04-20 00:03:12.679: V/AudioHardwareMSM72XX_wince(123): call snd_set_device 1
04-20 00:03:12.679: D/AudioHardwareMSM72XX_wince(123): rpc snd_set_device(1, 1, 1)
04-20 00:03:12.679: V/Libacoustic-wince(123): msm72xx_set_acoustic_done
04-20 00:03:12.679: I/Libacoustic-wince(123): ADRC Filter ADRC FLAG = ffff.
04-20 00:03:12.679: I/Libacoustic-wince(123): ADRC Filter COMP THRESHOLD = 2600.
04-20 00:03:12.679: I/Libacoustic-wince(123): ADRC Filter COMP SLOPE = b333.
04-20 00:03:12.679: I/Libacoustic-wince(123): ADRC Filter COMP RMS TIME = 106.
04-20 00:03:12.679: I/Libacoustic-wince(123): ADRC Filter COMP ATTACK[0] = 7f7d.
04-20 00:03:12.679: I/Libacoustic-wince(123): ADRC Filter COMP ATTACK[1] = 3096.
04-20 00:03:12.679: I/Libacoustic-wince(123): ADRC Filter COMP RELEASE[0] = 7ff7.
04-20 00:03:12.679: I/Libacoustic-wince(123): ADRC Filter COMP RELEASE[1] = 4356.
04-20 00:03:12.679: I/Libacoustic-wince(123): ADRC Filter COMP DELAY = 30.
04-20 00:03:12.679: I/Libacoustic-wince(123): Setting EQ Filter
04-20 00:03:12.679: I/Libacoustic-wince(123): IIR Filter FLAG = ffff.
04-20 00:03:12.679: I/Libacoustic-wince(123): IIR NUMBER OF BANDS = 04.
04-20 00:03:12.679: I/Libacoustic-wince(123): IIR Filter N1 = 00.
04-20 00:03:12.679: I/Libacoustic-wince(123): IIR Filter N2 = 4000.
04-20 00:03:12.679: I/Libacoustic-wince(123): IIR Filter N3 = 00.
04-20 00:03:12.679: I/Libacoustic-wince(123): IIR Filter N4 = 8000.
04-20 00:03:12.679: I/Libacoustic-wince(123): IIR FILTER M1 = 7616.
04-20 00:03:12.679: I/Libacoustic-wince(123): IIR FILTER M2 = 8732.
04-20 00:03:12.679: I/Libacoustic-wince(123): IIR FILTER M3 = 44d4.
04-20 00:03:12.679: I/Libacoustic-wince(123): IIR FILTER M4 = 3903.
04-20 00:03:12.679: I/Libacoustic-wince(123): IIR FILTER M16 = 3e8b.
04-20 00:03:12.679: I/Libacoustic-wince(123): IIR FILTER SF1 = 02.
04-20 00:03:12.679: E/Libacoustic-wince(123): msm72xx_enable_audpp: 0x0007
04-20 00:03:12.679: V/AudioHardwareMSM72XX_wince(123): AudioHardware::doUpdateVolume 1
04-20 00:03:12.679: V/Libacoustic-wince(123): msm72xx_start_acoustic_setting
04-20 00:03:12.679: I/AudioHardwareMSM72XX_wince(123): updating volume method=AUDIO
04-20 00:03:12.679: V/AudioHardwareMSM72XX_wince(123): doAcousticVolumeUpdate 1 1 5
04-20 00:03:12.679: V/Libacoustic-wince(123): msm72xx_set_acoustic_table 1 5
04-20 00:03:12.679: V/Libacoustic-wince(123): Update not required
04-20 00:03:12.679: V/AudioHardwareMSM72XX_wince(123): call snd_set_volume voice 5
04-20 00:03:12.679: D/AudioHardwareMSM72XX_wince(123): rpc snd_set_volume(1, 1, 5)
04-20 00:03:12.679: V/Libacoustic-wince(123): msm72xx_set_acoustic_done
04-20 00:03:12.679: D/AudioHardwareMSM72XX_wince(123): setVoiceVolume(1.000000)
04-20 00:03:12.679: I/AudioHardwareMSM72XX_wince(123): Setting in-call volume to 5 (available range is 0 to 5)
04-20 00:03:12.679: V/AudioHardwareMSM72XX_wince(123): doAcousticVolumeUpdate 256 0 5
04-20 00:03:12.679: V/Libacoustic-wince(123): msm72xx_set_acoustic_table 256 5
04-20 00:03:12.679: V/Libacoustic-wince(123): Update not required
04-20 00:03:12.679: V/AudioHardwareMSM72XX_wince(123): call snd_set_volume voice 5
04-20 00:03:12.679: D/AudioHardwareMSM72XX_wince(123): rpc snd_set_volume(256, 0, 5)
 
  • Like
Reactions: rigo007, ToughGuy and tm.bax
V

vouager

Senior Member
Jan 15, 2007
82
19
Also, you needed driverr for TPA2016 Chip
Read this!
xdandroid.com/irclogs/%23xdandroid.20100729.log.html
And search Google for TPA2016 android driver

I have found one Driver here:
gitorious.org/linux-on-qualcomm-s-msm/linux-msm/commit/dec7729227bf3601e349a3947636a8e760b5c366?format=html&utm_source=twitterfeed&utm_medium=twitter

Regards
 
Last edited:
  • Like
Reactions: tm.bax
spithash

spithash

Senior Member
May 21, 2010
153
27
OnePlus 5T
Google Pixel 4a
Hey guys I wanted to ask a little question :p .Will the patch for transparent statusbar work in our Minis? Had anybody tested it ??

P.S I need transparent status bar!There are some sexy themes out there :D

Edit: I used UOT Kitchen and it worked! Gj me
 

Attachments

  • shot_000001.png
    shot_000001.png
    112.9 KB · Views: 218
Last edited:
  • Like
Reactions: dstar000 and rigo007
W

wout

Senior Member
Jul 2, 2005
246
0
gps not working

Dear all,

How can I get GPS to work on this rom ?
Tried reflashing 4times, went back to wm6.5 leaving gps on and installed android again.
still no luck....

any ideas ?

greetings,
Wout
 
B

bas.bas

Senior Member
Jan 6, 2012
94
77
Hi wout

wout said:
Dear all,

How can I get GPS to work on this rom ?
Tried reflashing 4times, went back to wm6.5 leaving gps on and installed android again.
still no luck....

any ideas ?

greetings,
Wout
Click to expand...
Click to collapse

http://xdaforums.com/showpost.php?p=24064645&postcount=544
and 29 times you can reflash, it will not work properly, if you forget to do this:

Mounts and Storage Menu

------------------------
CWM-based Recovery v5.0.2.7
Formatting /boot...
Done.
Formatting /cache...
Done.
Formatting /data...
Done.
Formatting /system...
Done.



http://xdaforums.com/showpost.php?p=21810673&postcount=97

schlund said:
solution is quite simple:
enter CWM Recovery, format "boot, system, data, cache" -partitions, and install again !
Seems you have still st from your old version on your installation!
Click to expand...
Click to collapse
 
Last edited:
munjeni

munjeni

Senior Member
Jun 2, 2011
9,720
22,375
Battery controler/chip/or_what inside photon is the same as in aria... when I jtag-ed my aria with windowsce flash, battery worked perfect like worked in wince in my photon, so I'm 100% sure kernel module from aria with small modifications to rpc_call/smem_address will bring you batery driver like in aria!!! Allso I think for audio allso. Difierence photon/aria is very litle... only diference is aria have compas and oj, aria have small un-aligments on touch screen, aria have diferent butons: home,menu,back,search... only buttons controler not worked in aria when I installed wince, all other worked perfect (wifi, gps, audio, radio, bluetooth...etc)!
 
Last edited:
  • Like
Reactions: ssamth2003, peter08po, Unreal2k3 and 2 others
You must log in or register to reply here.

Similar threads

munjeni
[ROM] CM9 4.0.4 ICS HTC HD Mini [16.Jul.2012]
Replies
921
Views
349K
multiwirth
multiwirth
tzacapaca
[TUTORIAL] /!\Install Android on HTC HD Mini
Replies
1K
Views
398K
jotha
jotha
Cotulla
[ROM] [PORT] Ad Photon (discontinued)
Replies
422
Views
237K
superzuan
superzuan
krook6023
[DEV Discussion] HD Mini Android/Linux Development Thread
Replies
726
Views
237K
munjeni
munjeni
derefas
[ROM]HTC HD Mini Sense 3.5
Replies
239
Views
110K
Abdulla_91
Abdulla_91

Top Liked Posts

24 Hours All time
  • There are no posts matching your filters.
  • 102
    S
    schlund
    photonic CM 7.2​

    What is Photonic ?​

    Photonic is a unofficial port of Cyanogenmod, almost AOSP Version 2.3.7 - photonic kernel 2.6.35 Changes are minimal, sources are open. For further information visit github or official Cyanogenmod on the web!

    Sources are written to support NAND Boot (a replacement of Winmobile ROM incl. bootloader & recovery system) and SD-CARD Boot (classic boot from winmobile via haret)
    ​

    - Current Status -

    bugged/not working:
    these will be fixed in later releases

    • HQ/HD Video Playback
    • Video Recording
    • Audio via Bluetooth
    • FM Radio (Neither Headset nor Speaker)
    • Headset Stereo

    what should be fixed before next release:
    when list is finished next release will be uploaded
    • Battery driver (started but not finished)

    History
    18/06/12 - r10
    • Bootloader with new Partition-layout: Increases Phone Storage Size DONE!
    • Cut screen DONE! by derefas
    • update to latest official CM7 sources
    • ARM11 not going to suspend and causing battery drain DONE!
    • WIFI Stability and Tethering DONE!

    23/01/12
    • Rewritten wifi_nvs driver to get device specific calibration data and real mac address on NAND DONE!
    • GPS driver DONE!
    • Hundrets of lines of unlisted fixes like several clock, dsp, audio, data transfer, wifi, bt and code fixes DONE!

    downloads:
    (feel free to link to the downloads, but please DO NOT MIRROR! If you're having problems with downloading the files ASK ME!)

    NAND-Boot:
    1. Files for SD-Card - (needed to boot into fastboot to flash lk for the first time)
    2. Files for PC - (contains new bootloader&recovery, fastboot and drivers)
    3. Update.zip file - (is the main build file)
    3. latest GAPPS - (Google Apps like Market etc.)
    Click to expand...
    Click to collapse
    SD-Boot:
    not updated to r10, yet
    1. SD-Pack - Mirror 1 - (all in one)
    Click to expand...
    Click to collapse

    EXPERIMENTAL UPDATES:
    1. r11 - infos see GooManager
    Click to expand...
    Click to collapse



    - Credits -
    cotulla - for his initial 2.6.29 kernel port
    Alexander Tarasikov - for his initial lkbootloader
    the whole xda-photon people for the common project

    - Disclaimer -
    This product is free to use at your own risk. We take no
    responsibility for any conflict, fault, or damage caused by
    this unlocking procedure. No warranties, implied or otherwise, are given if you agree to use this product.
    No problems were found while testing this product on several different devices, your experience may vary.
    View
    53
    S
    schlund
    Instructions for a clean! Installation: NAND-BOOT
    This procedure will wipe all your data! So backup your content before you continue!

    STEP 1: Installing LK Bootloader & Recovery
    (If you have already installed a NAND version, you can skip the haret boot part, but it is very important to flash the new bootloader from lk-photonic-pc-r10.rar!! It contains important changes for wifi calibration!)
    1. Download all files for NAND (see downloads)
    2. Extract lk-photonic-pc-r10.rar to somewhere on your PC
    3. Copy cm-7-20120618-UNOFFICIAL-photonic-r10.zip, the GAPPS file and the content of lk-photonic-sd.rar archive to the root of your sdcard and run HaRET from your device
    4. The device should boot to the fastboot prompt. Connect the USB cable
    5. If your connecting your phone for the first time to your pc you may have to install drivers from the folder you have just extracted.(See also here) You can see it in your windows notification bar if you were sucessful. Be sure to have already run haret and already being in fastboot console on the device when installing drivers! If you are sill having problems to connect to the device via fastboot try installing HTC Sync (from htc website)
    6. Enter the Fastboot-folder on your pc (the one you have extracted) and run start-photonic.bat
    7. Choose Option "1" to flash Bootloader AND Recovery. The Batchfile will lead you. (Choosing CWM Recovery is recommended)
    8. If everything went fine choose Option "4" to reboot your deivce, now on HTC Bootscreen press and hold "Volume up" until you have entered the Recovery

    STEP 2: Installing the build
    (Once entered CWM Recovery you can control the menu with vol-up and down buttons, power button=enter)
    1. First, go to "mounts and storage"-menu and Unmount any partitions that can be unmounted (most likely, cache)
    2. Next, in "mounts and storage"-menu, format System, Data, Cache and Boot partitions
    3. Next, go to recovery main menu and select install zip from sdcard, then select choose zip from sd card
    4. Choose the cm-7-20120618-UNOFFICIAL-photonic-r10.zip
    5. Once done do the same to install GAPPS
    6. Select reboot system now
    7. Get some coffee and wait for the device to finish the first boot
    8. Hopefully your are done now and should see the setup wizard!
    9. Feel free to remove any of the files from SD-Card now, they are not needed anymore
    Click to expand...
    Click to collapse

    Instructions to UPDATE from a previous Photonic Release
    This should keep your old photonic data
    These Instructions are related to the previous one!
    1. DOWNLOAD cm-7-20120618-UNOFFICIAL-photonic-r10.zip, GAPPS and lk-photonic-pc-r10.rar
    2. Extract lk-photonic-pc-r10.rar to somewhere on your PC
    3. COPY the update-zip and GAPPS to your SD-CARD
    4. Boot into CWM Recovery: While in Android press and hold "Power" Button, choose "Restart", then choose "Recovery". Device will reboot in Recovery now. You can also simply boot up the device and hold "Volume up" button when HTC logo appears.
    5. Choose Option "Backup and Restore" and let it do a full Backup.
    6. Reboot the device and press "Volume down" to enter Fastboot mode
    7. Run start-photonic.bat on your PC from the folder you have it extracted to
    8. Choose Option "1" and install new Bootloader and Recovery and follow instructions
    9. When finished reboot and enter Recovery again with holding "Volume up" when HTC logo appears
    10. Format boot, cache, system and data partition im "mounts & storage"
    11. choose "backup and restore" again, but NOW you restore your previously saved backup!
    12. Next, go to recovery main menu and select install zip from sdcard, then select choose zip from sd card
    13. Choose the cm-7-20120618-UNOFFICIAL-photonic-r10.zip
    14. Once done do the same to install GAPPS
    15. Reboot the phone and be happy with the Update!
    Click to expand...
    Click to collapse

    Installation Instructions for SD-BOOT

    1. Download file for SD-Boot (see downloads)
    2. Copy the content of the archive to the root of your sd-card
    3. Run Haret from your device
    4. After several minutes(up to 10 minutes, screen looks like freezed!) CM7.2 Splashscreen should appear and some minutes later you should see the Setup Wizard!
    5. Give it some minutes then to finish installations in backround before you continue
    Click to expand...
    Click to collapse

    How to go back to WinMobile NAND-BOOT

    1. Download official Stock ROM for your device from HTC Site. Take care of the language and provider brandings! It will only one work for your phone! If you have really no idea which one to take you can contact their support, they will help you!
    2. Start the Utility you have just downloaded
    3. Be sure to have enough battery power, at least 50% !!
    4. Unplug/Plug battery of your phone, press and hold! Volume down then press power button
    5. You should have entered 3-Color Screen now, plug the phone with your computer and start the tool! wait for the progress beeing done

    If you are having problems with connection while flashing do it this way!
    Click to expand...
    Click to collapse
    View
    32
    S
    schlund
    Version tracking and Following EXPERIMENTAL BUILDS
    You may have noticed that i added some version tracking:

    The "-rX" in the filenames show the growing release number (Example: -r10)
    I removed ROM Manager and added GooManager instead, you can browse the files on the phone, checkout and install experimental updates etc. It will also let you know if there is an update!

    In the "Photonic" Folder there are two other folders: EXPERIMENTAL and RELEASE
    RELEASE is thought to be main, most stable and tested version, that most people should use. Experimental updates will only be included after heavy testing there
    EXPERIMENTAL is the storage for brand new tests on kernel and the android build, i will write the changes to the changelogs for the files so you can decide if you want to test it

    In most cases its "safe" to install experimental updates, feedback to them (using this forum thread) can really help me with developement.
    People that did hard to install the Photonic Release itsself should not try to test them.
    Click to expand...
    Click to collapse

    When having problems with the drivers
    To install the Android USB driver on Windows 7 for the first time:

    1. Connect your device to your computer's USB port.
    2. Right-click on Computer from your desktop or Windows Explorer, and select Manage.
    3. Select Devices in the left pane.
    4. Locate and expand Other device in the right pane.
    5. Right-click the device name and select Update Driver Software. This will launch the Hardware Update Wizard.
    6. Select Browse my computer for driver software and click Next.
    7. Click Browse and locate the USB driver folder.
    8. Click Next to install the driver.

    To install the Android USB driver on Windows XP for the first time:
    1. Connect your device to your computer's USB port. Windows will detect the device and launch the Hardware Update Wizard.
    2. Select Install from a list or specific location and click Next.
    3. Select Search for the best driver in these locations; un-check Search removable media; and check Include this location in the search.
    4. Click Browse and locate the USB driver folder.
    5. Click Next to install the driver.
    Click to expand...
    Click to collapse
    View
    28
    S
    schlund
    the "liberated" image is ready, i have spent my spare time from the last weeks with it, to see if its worth finding a way to do it.

    Now i am at a point where i can say: Yes it is possible!

    for explanation how it works:

    we have 2 cores in our chipset, with each running a system on it.
    Arm9 core, running iguana rtos, that you do not notice as casual user, and
    Arm11 core, that is running wm/android, all the stuff you see on your display

    system is going up with 2 generic bootloaders by qualcomm, that bring up the hardware, first thing that happens, done by htc is "oemsbl" bootloader, running on arm9. that one loads amss (iguana) from nand to ram on arm9,it is doing everything with the modem and phone i.e.. amss is running on nand in a special efs partition. (we can not overwrite this one while the device is running, but we also dont need to). oemsbl also inits appspl (our SPL-Bootloader) on arm11. since here arm9 and arm11 have several interfaces to communicate with each other. we are lucky, most things are done via shared memory. SPL (appspl) starts the os then.

    so, what we want to do is flashing a different appspl, oemsbl and amss now, also we have to change the layout of htc partition.

    is that possible? YES
    we are lucky, the partitionlayout of these partitions are the same, so once they are loaded from nand to memory (except efs) we can change them while system is running.

    of course, this is a very risky procedure, as it is always when flashing spl and radio but its possible.

    what holds me back now ? the parts on nand we want to overwrite are locked. its my job now to find a way to unlock them, but the people that are involved in my work know, i am having good progress and i am very close ;)

    when will there be a release ? thats hard to say, ones unlocked, theres not much to do anymore, have to write a flash tool for DAU's, an other tool for copying your serials, imei's & mac's is already finished. also the first 2 android versions are finished now.

    will it be a "real" aria ? It will tell you so, but it's not. there are minor hardware differences that i had to fix in kernel & systems. but in general its possible to boot every aria release (with several things not working)

    are there any bugs left ? NO
    View
    21
    S
    schlund
    hey guys, sorry for the missing status update;

    i have decided to do some test before posting my status with battery driver. but happily the last test isnt over yet, waiting for the battery beeing empty since 50h now!

    well, i think the test will take about 10 more hours, but i will post the detailed results then :)
    View

New posts