Please share it!
Here... don't flash the hboot unless you want your internal memory wiped.
Here... don't flash the hboot unless you want your internal memory wiped.
http://dl.dropbox.com/u/66746543/ControlBearRelease-vigor-ics-windows.zip
It should work now... just tried it.
ok i finall fixed my device from being stuck on the htc white screen,
to fix this do the following.
1.download the gb Ruu ( make sure you are on gingerbread firmware, 2.01) not sure if this will work form the ics firmware.
2.flash it, it may fail once, if it does try again it will eventually flash successfully
after its done reflash your recovery, and done s-off and unlocked device, somehow they still remain?
SUCCESS - Taking a sip.
SUCCESS - Beer is tasty.
SUCCESS - Beer is tasty.
SUCCESS - Beer is tasty.
SUCCESS - Beer is tasty.
SUCCESS - Buddies and Beer
Checking alcohol level......
Seems to be just right.....
Let's take one more......
Aaaah, nice sunny day!!
Rebooting.......
Waiting device....
Fastboot detected
Beer is tasty, lets take another!!
Found device... Please wait...
Rebooting bootloader.......
Waiting device....
Now phone is on recovery and not doing anything. Still on waiting device.... Ideas? Wait?
tyvm it workedHere... don't flash the hboot unless you want your internal memory wiped.
http://dl.dropbox.com/u/66746543/ControlBearRelease-vigor-ics-windows.zip
Flash this patch right here in recovery...tyvm it worked
the only problem i have right now is that its not recognizing my 16gb card for some reason
edit:i tried booting into the recovery and the sd-ext mount works, so should i just reinstall the ROM?
V.02 screws up restoring backups. Go back to V.01. I posted it in the last page or two. Don't flash the hboot if it asks or you're internal memory will get wiped.For some reason I can't get anywhere with this. Gets to transferred backups then backup failed press enter to exit. Not really sure what I haven't done. I have all the files in the same directory as fastboot/adb and have the drivers installed. USB debugging is also enabled. Has anyone else seen the same error?
SUCCESS - Taking a sip.
SUCCESS - Beer is tasty.
SUCCESS - Beer is tasty.
SUCCESS - Beer is tasty.
SUCCESS - Beer is tasty.
SUCCESS - Buddies and Beer
Checking alcohol level......
Seems to be just right.....
Let's take one more......
Aaaah, nice sunny day!!
Rebooting.......
Waiting device....
Fastboot detected
Beer is tasty, lets take another!!
Found device... Please wait...
Rebooting bootloader.......
Waiting device....
Now phone is on recovery and not doing anything. Still on waiting device.... Ideas? Wait?
What does this patch contain gray?
Sent from my Htc Rezound
Follow me on twitter @lmrtech
Prerequisites said:Prerequisites
In order to use JuopunutBear you must meet the following pre-requisites:
Be unlocked using the HTCdev bootloader unlock
Be rooted (have superuser and/or an unsecured boot image installed)
Have a spare microSD card, or to have backed up all contents of your SDcard
Have fastboot and adb drivers installed and working (windows)
Have usb debugging enabled
Have a legth of insulated wire of sufficient length to join the contact points for your device. See images and videos for device specific information.
Instructions said:Instructions
(Optional) Perform a full backup and replace your sdcard with one that you are willing to wipe.
Ensure that your battery is fully charged.
Choose the correct download for your device and operating system
Extract the zip file to a new directory
Verify the MD5 checksum for your download
Read and/or watch the video for the device specific information for your device
Run controlbear as admin(windows) or root or using sudo on linux
Follow the on-screen instructions from ControlBear
Do not press any of the buttons on the phone during the process.
After doing the “wire-trick” yor phone will reboot. The sequence of the reboot may vary somewhat from that you see in the videos as these were taken during various stages of development.
If you see the following message from ControlBear after doing the wire trick:
ErrorMsg: Still sober.
This means that you have been unsuccessful in implementing the wire-trick. Run ControlBear again.
The usual casue for this is that you failed to perform 2 clean contacts or mistimed the wire trick.
Your phone will reboot several times during the process, this is normal. ControlBear will tell you when it has finished whether sucessfully or not.
Wire Trick said:Wire Trick
The “wire trick” is an essential part of the JuopunutBear S-OFF procedure.
When instructed to do so by the program you must perform the “wire trick” which is done as follows.
Obtain an insulated wire of appropriate length and gauge
Insert one end of the wire into the hole where pin 1 is indicated in the picture below, ensuring that a firm contact it made with the metal contact at the bottom of the hole
Briefly touch to other end of the wire to the contact marked GND in the picture below.
Wait approximately 1.75 seconds and then again touch the wire to the marked GND.
Allow the program to continue.
Note: it may take several attempts of running the program in order to obtain the correct timing for the wire trick.
The contact points for the “wire trick” are shown in the picture below.
Fix for external SD is as follows:
- Install busybox
- adb shell busybox fdisk /dev/block/mmcblk1
- type o
- type w
- adb shell busybox fdisk /dev/block/mmcblk1
- type n
- select primary, then 1
- chose default sizes
- type w
- adb shell busybox mkfs.vfat /dev/block/mmcblk1p1
For those of you having problems with internal storage, my apologies. We accidentally included the GB hboot.
Download this:
http://dl.dropbox.com/u/14779955/jb_hboot.zip MD5: b05336c08f709bf0a909205bcb95b951
Put the phone in fastboot mode, then run the follwoing commands:
Code:fastboot oem rebootRUU fastboot flash zip jb_hboot.zip fastboot reboot
Ignore the green bar.