Just install it. wifi and mobile signal very very low.
Signal strength 2147483647 dBm 255 asu. It must be -60 dBm here where im sitting.
Thanks for the heads up. I will take a look at that.
Also, I uploaded the gapps I've been using to this site and updated the links. I feel like I need to scrub my hard drive everytime I go to Devhost(d-h.st.com) so its probably for the best that I stop using them to host files.
Busybox is included. You should be able to install the Xposed framework but I can't vouch for the modules. I know nothing about gravitybox so I can't give you any info on support for it.Thanks for keep it up. Is that busybox, Xposed, gravitybox supported I have made little modification with these apps.
Busybox is included. You should be able to install the Xposed framework but I can't vouch for the modules. I know nothing about gravitybox so I can't give you any info on support for it.
So, I take a try to install these.
trackball to awake only work when phone have been charge, otherwise not work
Which version are you running? In version 1.0.6, there is a bug in the power management that was putting the trackball gpio to sleep when it is off-charger but this is fixed in 1.0.7.
I have updated the bug section on the main post with the signal strength issue. I found the problem with and I have it fixed on my test phone so the fix should be in the next version I release.
1- Running 1.0.7. trackball not working for me. (screenshot below)
2- Write access denied at sys/android_touch.
3- I have in previous its working well for me. Would you like to add sweep2wake feature. (screenshot below)
Verify that Settings->ASX options->Trackball Wake is checked.
If the box is check and you are still unable to wake with the trackball then:
1. Reboot into recovery
2. Backup
3. Wipe data/factory reset
4. Reboot
Let me know if this works.
Actually do this instead:yup I do that but not working.
Later this week I do that again.
thanks
Actually do this instead:
1. Reboot into recovery
2. Backup
3. Wipe data/factory reset
4. Re-flash 1.0.7 without flashing GAPPS
5. Reboot
Actually do this instead:
1. Reboot into recovery
2. Backup
3. Wipe data/factory reset
4. Re-flash 1.0.7 without flashing GAPPS
5. Reboot
I also flashed this ROM but the trakpad waking isn't working. However this is really a minor thing for a well functioning ROM. I did not expect this phone is still supported by the community. Truly amazing work thank you! Now my MT4G is awaken from a 4 year hibernation and will serve as a smart remote in my living room .
I can't for the life of me get the latest version to install. I've tried doing it through several recoveries and have tried several versions of the rom. The highest I've been able to flash is 1.0.5, and it was buggy as hell. Anything higher and my phone will get stuck in the boot sequence (won't go past the splash screen). I've also tried doing it via OTA update on 1.0.4 (1.0.5 OTA wouldn't work), and it would fail after download. Any suggestions?
[B]1.0.9[/B]
- Fixed boot crash for Glacier phones with "M4G2DE" model internal flash.
- Fixed issue where headphones were not recognized.
- Added hardware key custom rebinding from CM.
- Allow camera button (long press) to select different camera app.
- Camera Updates
- Fixed issue where using the camera button to focus would not turn off LED when button is released.
- Fixed issue where using the camera button to focus would break the next call to focus.
- Fixed occasional freeze when taking a picture.
[B]1.0.8[/B]
- Switched to JB sound package.
- Fixed bug where incorrect signal strength was being reported.
- Camera Updates
- Added Auto-Focus
- Auto exposure improvements
- Added WVGA camcorder mode
[B]1.0.7[/B]
- Added blue notification led
- Fixed display auto-brightness
- Fixed physical button lights
- Fixed issue where SetupWizard would not finish properly
- Fixed YouTube video playback.
- Fixed issue where copying to phone with USB Mass Storage would be 3 times slower.
- Camera Updates
- Added flash for camera. This also fixes Torch.
- Tweaked auto exposure to adjust faster.
- Kernel Updates
- Tweaked power management idle and sleep modes.
- Fixed trackball wake when sleeping.
- Fixed issue where CPU frequency was stuck at 768Mhz.
- Fixed issue where user-configured max CPU frequency not being restored at boot.
- Added overclocking support.
- Allow CPU frequency to be underclocked at 192Mhz. Originally set at 256Mhz.
[B]1.0.6[/B]
- Lots of kernel updates:
- USB driver updated to JB 4.2.2 from CAF
- Kernel version updated to 2.6.36
- Clocks, power management, etc updated to 2.6.38/CAF.
- Improvements made to camera daemon
- GPS Fixed
- Added current CPU speed in Performance settings.
[B]1.0.5[/B]
- Fixed SIM card not being recognized
- OTA Tweaks
[B]1.0.4[/B]
[U]Android updates[/U]
- All but four ICS packages updated to JB MR1
- OTA Updater fixed
- Performance settings, Advanced reboot and Kill app back button options re-added from aospX
- Root access settings added
- Complete rewrite of mm-open-daemon:
- Added support for front facing camera
- Improved auto exposure algorithm
- Wrote formulas to calculate several VFE settings instead of hard coding them, allowing different camera modes to be utilized
- Added different modes/resolutions for both camera sensors
- Various other fixes/improvements
- Updated to CAF Camera App
- Adreno Blobs Updated to JB MR1
- Fixed bug where animations would not render the last frame
- Fixed audio not recording for camcorder
[U]kernel updates[/U]
- Framebuffer driver updated
- GPU driver updated
- New Camera2 driver for MT9V113 (FFC)