FORUMS
Remove All Ads from XDA

[Q] Motorola Atrix Hard Brick failed to boot 0x1000

144 posts
Thanks Meter: 10
 
By Andr3s, Senior Member on 1st March 2012, 09:39 PM
Post Reply Email Thread
22nd May 2013, 01:30 AM |#31  
Junior Member
Thanks Meter: 0
 
More
Unhappy Boot failed error
Quote:
Originally Posted by mcjinx216

People on here shouldnt give up so easily, I have a solution for failed to boot brick.

Download moto-fastboot, and unzip to C:\moto-fastboot
DL here:http://www.android-advice.com/file-d...rix_Root_Files

Download system image for 2.3.4 and unzip to moto-fastboot folder
DL here http://www.android-advice.com/file-d...bread_4591_ROM

Download atrix oem unlock and unzip to moto-fastboot folder
DL here:http://gititbit.ch/pub/unlock.zip

open cmd and navigate to C:\moto-fastboot\

Force fastboot on phone by holding down PWR and VOL UP while inserting battery.

Type these commands:

moto-fastboot oem unlock (it will show atrix ID re-enter with ID at end of line)

when finished, then enter these commands:

moto-fastboot flash boot boot.img

moto-fastboot flash system system.img

moto-fastboot -w

moto-fastboot reboot

When it reboots, you will be back to stock, fully restored!!

I then used Pete's Motorola Tools to root my atrix.
Info and DL here http://www.psouza4.com/Bionic/
yes it did work on my atrix make sure usb debugging is on and unknown sources checked.

I then installed CWM to my Atrix
DL here http://forum.xda-developers.com/show....php?t=1475444
unzip to moto-fastboot, put atrix in fastboot mode and open cmd, navigate to moto-fastboot folder and type this:

moto-fastboot flash recovery recovery.img

Reboot and you are DONE!!!! All thats left is to find a ROM and you are good to go.

Hello sir, i m facing a serious proble with my moto atrix MB860.

i used RSD process and bricked my phone.
it shows SVF:105:1:2
failed to boot 0x1000
and after 1 - 2 seconds screen become blank.

is there any solution for this hard brick. im soo much worried about my phone and cant afford this big loss for me.
or add me at skype ([email protected] and [email protected].
i will very very grateful to you.
 
 
4th August 2014, 04:25 AM |#32  
Junior Member
Thanks Meter: 0
 
More
[QUOTE=mcjinx216;23738497]People on here shouldnt give up so easily, I have a solution for failed to boot brick.

Download moto-fastboot, and unzip to C:\moto-fastboot
DL here:http://www.android-advice.com/file-d...rix_Root_Files

Download system image for 2.3.4 and unzip to moto-fastboot folder
DL here http://www.android-advice.com/file-d...bread_4591_ROM

Download atrix oem unlock and unzip to moto-fastboot folder
DL here:http://gititbit.ch/pub/unlock.zip

open cmd and navigate to C:\moto-fastboot\

Force fastboot on phone by holding down PWR and VOL UP while inserting battery.

Type these commands:

moto-fastboot oem unlock (it will show atrix ID re-enter with ID at end of line)

when finished, then enter these commands:

moto-fastboot flash boot boot.img

moto-fastboot flash system system.img

moto-fastboot -w

moto-fastboot reboot

When it reboots, you will be back to stock, fully restored!!

I then used Pete's Motorola Tools to root my atrix.
Info and DL here http://www.psouza4.com/Bionic/
yes it did work on my atrix make sure usb debugging is on and unknown sources checked.

I then installed CWM to my Atrix
DL here http://forum.xda-developers.com/show....php?t=1475444
unzip to moto-fastboot, put atrix in fastboot mode and open cmd, navigate to moto-fastboot folder and type this:

moto-fastboot flash recovery recovery.img

Reboot and you are DONE!!!! All thats left is to find a ROM and you are good to go.[/QUOT












good day.......thanks for this info, but can you walk me through what you did step by step please, i'm having the same issue with my phone. i did what you did and now i'm stuck at failed to boot 1
4th August 2014, 04:30 AM |#33  
Senior Member
Flag Córdoba
Thanks Meter: 363
 
More
It is already step by step... Perhaps you missed the second fastboot oem unlock?

Enviado desde mi MB860 usando Tapatalk 2
4th August 2014, 03:07 PM |#34  
Junior Member
Thanks Meter: 0
 
More
Quote:
Originally Posted by andresrivas

It is already step by step... Perhaps you missed the second fastboot oem unlock?

Enviado desde mi MB860 usando Tapatalk 2





i realize that, but i meant walk me through it, in detail....sorry about that if it would take up time, but i would really love my phone to be up and running again
4th August 2014, 08:50 PM |#35  
Quote:
Originally Posted by sam584

i realize that, but i meant walk me through it, in detail....sorry about that if it would take up time, but i would really love my phone to be up and running again

You just described the procedure in detail. Follow the steps

Sent from my MB886 using xda app-developers app
9th August 2014, 06:27 PM |#36  
Junior Member
Thanks Meter: 0
 
More
Informative but didn't work... :/
Quote:
Originally Posted by mcjinx216

People on here shouldnt give up so easily, I have a solution for failed to boot brick.

Download moto-fastboot, and unzip to C:\moto-fastboot
DL here:http://www.android-advice.com/file-d...rix_Root_Files

Download system image for 2.3.4 and unzip to moto-fastboot folder
DL here http://www.android-advice.com/file-d...bread_4591_ROM

Download atrix oem unlock and unzip to moto-fastboot folder
DL here:http://gititbit.ch/pub/unlock.zip

open cmd and navigate to C:\moto-fastboot\

Force fastboot on phone by holding down PWR and VOL UP while inserting battery.

Type these commands:

moto-fastboot oem unlock (it will show atrix ID re-enter with ID at end of line)

when finished, then enter these commands:

moto-fastboot flash boot boot.img

moto-fastboot flash system system.img

moto-fastboot -w

moto-fastboot reboot

When it reboots, you will be back to stock, fully restored!!

I then used Pete's Motorola Tools to root my atrix.
Info and DL here http://www.psouza4.com/Bionic/
yes it did work on my atrix make sure usb debugging is on and unknown sources checked.

I then installed CWM to my Atrix
DL here http://forum.xda-developers.com/show....php?t=1475444
unzip to moto-fastboot, put atrix in fastboot mode and open cmd, navigate to moto-fastboot folder and type this:

moto-fastboot flash recovery recovery.img

Reboot and you are DONE!!!! All thats left is to find a ROM and you are good to go.



Hello sir. my atrix is bricked while using RSD .. it just shows the boot error and then blank display ..
I recently bought it for high cost.. it's not entering in fastboot mode aur rsd protocol mode..
i tried using nvflash recovery with factory repair cable.. but when i use any command .. Like "nvflash --sync" (the simplest) it shows :

Quote:

Nvflash started
rcm version 0X4
Command send failed (usb write failed)

then pc disconnects it .. I have JTag it.. but still not going in fastboot aur any other flash mode. :/ :/ :/

plzzzzz I need helppp
13th August 2014, 10:11 AM |#37  
wedgess's Avatar
Retired Forum Moderator / Inactive Recognized Developer
Flag Dublin, Ireland
Thanks Meter: 14,518
 
Donate to Me
More
Too much bickering going on here... I'm leaving this thread open so that you guys can hopefully fix your bricked devices but it will only remain open so long as the childish bickering stops. We do not need it here !! As this thread is old, a lot of links are down. Consider this a warning regarding the previous behavior within this thread .

Thread cleaned
The Following User Says Thank You to wedgess For This Useful Post: [ View ] Gift wedgess Ad-Free
13th August 2014, 10:13 AM |#38  
Quote:
Originally Posted by wedgess

Too much bickering going on here... I'm leaving this thread open so that you guys can hopefully fix your bricked devices but it will only remain open so long as the childish bickering stops. We do not need it here !! As this thread is old, a lot of links are down. Consider this a warning regarding the previous behavior within this thread .

Thread cleaned

Thanks for the more official and tactful way of trying to get things back on track. Comparing my last post to yours, yours is a bit more effective

Sent from my MB886 using XDA Free mobile app
14th August 2014, 01:27 AM |#39  
Junior Member
Thanks Meter: 4
 
More
fail to boot 0x1000
The phone shows fail to boot 0x1000 then shuts off
Things that dont work Holding the vol up and power while inserting the battery .. phone still shuts off
Rsd not detecting the phone because it turns off after the error comes up.
Recovery mode dont work , phones displays error then turns off.

What was notice though if you leave the battery in it drains it regardless of the fact that it turns off. However it would seem as if something is running with the lcd off because the battery does drain and also the only way to turn if back on is a battery pull. When you power on again you get the same error , hence you have to battery pull again.

By the way this is different from the other fail to boot 0x1000 that list the menu for you to choose from , that one is easily fixed by flashing over the rom. This one is not being detected by the PC which is why there seem to be no fix for it so far.
8th September 2018, 05:38 PM |#40  
Junior Member
Flag mount lavinia
Thanks Meter: 0
 
More
Great work and utmost help
Atlast I found a great help that I could unbrick my phone mb861. I could not find even build # on about phone. I tried too many methods. Thanksd a million
Quote:
Originally Posted by mcjinx216

People on here shouldnt give up so easily, I have a solution for failed to boot brick.

Download moto-fastboot, and unzip to C:\moto-fastboot
DL here:http://www.android-advice.com/file-d...rix_Root_Files

Download system image for 2.3.4 and unzip to moto-fastboot folder
DL here http://www.android-advice.com/file-d...bread_4591_ROM

Download atrix oem unlock and unzip to moto-fastboot folder
DL here:http://gititbit.ch/pub/unlock.zip

open cmd and navigate to C:\moto-fastboot\

Force fastboot on phone by holding down PWR and VOL UP while inserting battery.

Type these commands:

moto-fastboot oem unlock (it will show atrix ID re-enter with ID at end of line)

when finished, then enter these commands:

moto-fastboot flash boot boot.img

moto-fastboot flash system system.img

moto-fastboot -w

moto-fastboot reboot

When it reboots, you will be back to stock, fully restored!!

I then used Pete's Motorola Tools to root my atrix.
Info and DL here http://www.psouza4.com/Bionic/
yes it did work on my atrix make sure usb debugging is on and unknown sources checked.

I then installed CWM to my Atrix
DL here http://forum.xda-developers.com/show....php?t=1475444
unzip to moto-fastboot, put atrix in fastboot mode and open cmd, navigate to moto-fastboot folder and type this:

moto-fastboot flash recovery recovery.img

Reboot and you are DONE!!!! All thats left is to find a ROM and you are good to go.

Post Reply Subscribe to Thread

Guest Quick Reply (no urls or BBcode)
Message:
Previous Thread Next Thread
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes