Here is the JY mcu v2.16 that works in my JY S07 at 800x480. I was sure to have it removed from the Post #7500
Sorry if i confused it.
Greetings Ken
Thanks, I can comfirm yours is the type in this thread, sorry, what was your question again ? !
---------- Post added at 09:33 PM ---------- Previous post was at 09:30 PM ----------
The KGL widgets are different from the JY and KLD widgets. KLD and JY have a widget that is built into the launcher and displays either music, radio or BT music, depending on what is playing, but KGL have a separate widget for radio, music and BT music and theyve been the same since 4.2. As the KLD and JY types are built into the launchers, you wont be able to see them listed as widgets. You are right though, the KGL ones can be put on any of the other types whether 4.2, 4.4 or 4.4.2, personally I dont like the look of them and I dont like having 3 , I prefer having one multifunction one like KLD/JY. What I d like to do at some point is to try and make a multifunction one that is a proper widget (ie shows up in wuidgets as a widget) and not built into the launcher.
I'm a little confused. I have a KLD system with the 2.20 MCU and coudu's latest on it. When you say there's a widget built into the launcher that displays either music, radio, or BT music, what exactly are you talking about? I know on the home screen there are buttons for Music, Radio, and Bluetooth that launch what appear to be different apps.
I think he is talking about on the main launcher screen to the right side there is a widget that changes. If you are playing the radio, it will show the frequency, if you have an Ipod hooked up and are playing music from it it will show the track information. It changes the information displayed depending on what you are doing.
Steve
I'm a little confused. I have a KLD system with the 2.20 MCU and coudu's latest on it. When you say there's a widget built into the launcher that displays either music, radio, or BT music, what exactly are you talking about? I know on the home screen there are buttons for Music, Radio, and Bluetooth that launch what appear to be different apps.
I have one unit for my car Mazda 6 2009 it's very cool but I have one issue my unit without SD slot just GPS slot the issue all apps need SD Card. Always says insert SD card for record voice and video also torque app need it. I put USB memory but still that issue. What I can do for solve it
MCU version:
MTCB-KLD-V2.12
Model : S07
Android : 4.4.4
Apologies if this has been mentioned before, I have read most of the thread but am only up to page 500-ish. I also did search but found nothing like this.
Whilst testing some speakers, I ran a frequency sweep on the headunit (I have a Joyous as noted in my sig). When the sweep gets to around 450Hz, up until 600Hz, the main tone is copied with one that appears to be 3x the frequency. This does not depend on volume but purely on frequency and can be heard as a change in tone to one that is much sharper. I have tested with equaliser flat and loudness off. Please see the attached screengrab (taken with my mobile phone).
Can anyone else test out this behaviour?
I used FuncGen Signal Generator on the headunit and Spectrum Analyzer on the phone.
There are free space in internal but some apps like Sygic or voice recorder need external SD and my unit without it just GPS and two USB slot.
Hi,
Regarding letter "h" in the file name this update for 1024x600 HU's. But
posted link isn't able to download it.
Can You PM link to me ?
So, can You ask them to provide 800x600 android firmware ?
Here's the rooted version (update.img), with extended install-recovery.sh (from post #5336), KGL ?x? KK 4.4.4, from 20150115:
updateKGL?x?KK.part1.rar
updateKGL?x?KK.part2.rar
I don't know the screen resolution either (I don't know which file, if any, to look for, though I could see all, of course).
The MTC apps are of version 5 (not 3, as KLD has)(may be specific to KGL, or simply a newer version).
Apologies if this has been mentioned before, I have read most of the thread but am only up to page 500-ish. I also did search but found nothing like this.
Whilst testing some speakers, I ran a frequency sweep on the headunit (I have a Joyous as noted in my sig). When the sweep gets to around 450Hz, up until 600Hz, the main tone is copied with one that appears to be 3x the frequency. This does not depend on volume but purely on frequency and can be heard as a change in tone to one that is much sharper. I have tested with equaliser flat and loudness off. Please see the attached screengrab (taken with my mobile phone).
Can anyone else test out this behaviour?
I used FuncGen Signal Generator on the headunit and Spectrum Analyzer on the phone.
Lets ask our chinese friends to provide another oneHi,
You were right. I flash the update yesterday and it built for 1200x600 px screen resolution.
When I use Voice Recorder, it stores files on internal_sd. Are you using a different voice recorder app? What do you see when you go to Settings -> Storage: NAND FLASH?
Hi,
You were right. I flash the update yesterday and it built for 1200x600 px screen resolution.
---------- Post added at 07:22 AM ---------- Previous post was at 07:16 AM ----------
Hi,
Screen resolution is 1200x600
Interesting. I have a G2100 unit (also a JY). I'm going to run some test this evening and report back. Edit, I should note that I am using Viper4Android which uses the internal hardware amp rather than digital volume control.
Hi together this is an important announcement!
As you knew Mike an me we were talking about a dedicated section.
This is now achieved and I am requested by him to sort things out from here.
I will split out some Key knowledge posts, for example malaysks Firmware-Post, to new Threads in our subforums.
Developers
Please if you create new work open you own Thread in the new forums. If you already have posted here probably wait until I split your post out or write to me to ensure I will split you out if you think I missed you or you have a critical release.
Questionning Users
Please open your own thread for your questions in our new section. I can not split out every question from here. This thread will be left over for searching so please if you have current questions just ask in our new Q&A-Section.
I will start splitting up this thread in about one hour.
You can find the new section at the bottom of this link:
http://xdaforums.com/android-auto
Thank you!
- [user=853627]@coudu[/user] (rooted, stock). Early v4.0 and v4.1 have some problems.
- [user=3590033]@Malaysk[/user] (rooted, with very useful mods, some come with NEXT launcher)
- [user=6041319]@dsa8310[/user] (rooted, almost stock)
[B]- Boot Up:[/B]: time is around 30s.
[B]- GPS[/B]: GPS positions very fast. TomTom, Navigon, Sygic, and regular off-line GPS work. Navigon and Sygic have some problems with some ROMs
[B]- Stand by mode[/B]: Latest ROMs and MCU have the possibility of choosing stand by mode with various times chosen.
[B]- Radio:[/B] radio stations are saved as frequencies
[B]- Bluetooth contacts:[/B] contacts are saved on the device.
- Works fine with Bose system (Audi)
- Possible ground loop noise that needs some tricks to be removed (see section problems)
- Torque works and can run in parallel with A2DP
- ELM327 works (might need special app like CarService in very weird cases)
- Camera works (might be better to get the one with RK3188 chip)
- There is no automatic brightness control because the unit does not have light sensor, but there are apps that can help
- The touch screen is extremely responsive. It works as good as most phones.
1- Install the APK.
2- Make sure you are connected to WiFi and you have an internet connection.
3- Open Root Master (do not upgrade to newer version unless you can read chinese, The newest version has different options, all in chinese. Version 2.1.1 just has a button that says "root".))
4- Press root button
5- Chinese characters will flash across the screen.
6- A second popup box will appear, press the purple button.
- cd /mnt/sdcard
- su
- pm install "NameOfTheApp".apk