[Q] CMW

Search This thread

69saimon69

Member
Jan 16, 2014
21
2
Hello,

I have SGS2+ and Stock 4.2.2 for Slovakia Country (I9105PXWUBML1). What CWM is for me? I try Jerry but Odin don´ť say me "Leave CS" only "end....". I try rename file just .tar. After reboot I haven´t CWM.. Could you help me please? Debugging is on.

I am noob, I know it :(
 
Last edited:
Hello,

I have SGS2+ and Stock 4.2.2 for Slovakia Country (I9105PXWUBML1). What CWM is for me? I try Jerry but Odin don´ť say me "Leave CS" only "end....". I try rename file just .tar. After reboot I haven´t CWM.. Could you help me please? Debugging is on.

I am noob, I know it :(

Use this and select the right CWM for your phone and flash it with Odin.
 
  • Like
Reactions: 69saimon69

69saimon69

Member
Jan 16, 2014
21
2
What is wrong?

Copy from Odin:
<ID:0/023> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CWM-6.4.5_4.2.2_ODIN-s2vep.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/023> Odin v.3 engine (ID:23)..
<ID:0/023> File analysis..
<ID:0/023> SetupConnection..
<ID:0/023> Initialzation..
<ID:0/023> Get PIT for mapping..
<ID:0/023> Firmware update start..
<ID:0/023> recovery.img
<ID:0/023> NAND Write Start!!
<ID:0/023> RQT_CLOSE !!
<ID:0/023> RES OK !!
<ID:0/023> Removed!!
 

andixlm

Senior Member
Jun 16, 2012
285
1,069
What is wrong?

Copy from Odin:
<ID:0/023> Added!!
<OSM> Enter CS for MD5..
<OSM> Check MD5.. Do not unplug the cable..
<OSM> Please wait..
<OSM> CWM-6.4.5_4.2.2_ODIN-s2vep.tar.md5 is valid.
<OSM> Checking MD5 finished Sucessfully..
<OSM> Leave CS..
<ID:0/023> Odin v.3 engine (ID:23)..
<ID:0/023> File analysis..
<ID:0/023> SetupConnection..
<ID:0/023> Initialzation..
<ID:0/023> Get PIT for mapping..
<ID:0/023> Firmware update start..
<ID:0/023> recovery.img
<ID:0/023> NAND Write Start!!
<ID:0/023> RQT_CLOSE !!
<ID:0/023> RES OK !!
<ID:0/023> Removed!!

It's all right.
 

andixlm

Senior Member
Jun 16, 2012
285
1,069
Odin not write PASS only RESET! It´s okey?

Yes, it's ok. Try this by @CoolDevelopment

(If stock flashes back stock recovery automatically(some peoples phones do that))
1. Complete guide above until step 4.
2. Klick on PDA and select *filename*.tar.md5. Check that "F. Reset Time" is set and nothing else.
3. Pull out your phones battery.
4. Reboot into recovery(with Home+Power+Volume Up)
5. You should get a message to prevent rom from flashing stock revcovery, answer yes
 
  • Like
Reactions: 69saimon69

Top Liked Posts

  • There are no posts matching your filters.
  • 1
    Hello,

    I have SGS2+ and Stock 4.2.2 for Slovakia Country (I9105PXWUBML1). What CWM is for me? I try Jerry but Odin don´ť say me "Leave CS" only "end....". I try rename file just .tar. After reboot I haven´t CWM.. Could you help me please? Debugging is on.

    I am noob, I know it :(

    Use this and select the right CWM for your phone and flash it with Odin.
    1
    Odin not write PASS only RESET! It´s okey?

    Yes, it's ok. Try this by @CoolDevelopment

    (If stock flashes back stock recovery automatically(some peoples phones do that))
    1. Complete guide above until step 4.
    2. Klick on PDA and select *filename*.tar.md5. Check that "F. Reset Time" is set and nothing else.
    3. Pull out your phones battery.
    4. Reboot into recovery(with Home+Power+Volume Up)
    5. You should get a message to prevent rom from flashing stock revcovery, answer yes