Galaxy S I9003 Q&A
- Thread starter HairyScot
- Start date
Install:
Android Assistant and configure the 2 auto clean options under settings.
Install:
MinFreeManager
Set it to agresssive. (May cause some force closes)
So far works great for me.
Extras:
Try to install:
Xposed and greenify.
Sent from my E310 using XDA Free mobile app
Android Assistant and configure the 2 auto clean options under settings.
Install:
MinFreeManager
Set it to agresssive. (May cause some force closes)
So far works great for me.
Extras:
Try to install:
Xposed and greenify.
Sent from my E310 using XDA Free mobile app
Q
Hello,
1. my camera app is crashing, when I turn it on.
I'm using nameless-4.4.3-20140615-galaxysl-WEEKLY but happens in every nameless rom.
how can I repair it?
Is it the only way to change the stock one?
does anyone have the working camera stock app?
2. When I try to plug in my car charger, the phone doesn't charge.
I need to reboot the phone, then it is charging?
does anyone know what to do?
thaks in advance.
Hello,
1. my camera app is crashing, when I turn it on.
I'm using nameless-4.4.3-20140615-galaxysl-WEEKLY but happens in every nameless rom.
how can I repair it?
Is it the only way to change the stock one?
does anyone have the working camera stock app?
2. When I try to plug in my car charger, the phone doesn't charge.
I need to reboot the phone, then it is charging?
does anyone know what to do?
thaks in advance.
Greetings;
For now i would suggest you to
Perform a clean install and flash stock firmware (you can find it on sammobile website - requires registration).
Clean Install Step by Step:
1) Remove SD Card
2) Reboot your device in CWM Recovery Mode.
(If CWM is not there; flash CF-Root)
Select: "Advanced" and Erase Dalvik Cache.
Go back and Select: "Mounts and Storage"
And Format:
- Data
- System
- Boot
- Cache
After that Power Off your device and boot into download mode.
Open Odin; plug the USB Cable; select the firmware file under "PIT"
Press start; and wait untill Odin says "Pass".
Note that 1st boot takes longer.
Also do not remove the cable utill Odin says "Pass"
Let me know how it went.
The charging issue on the car charger may be due to a broken pin or incompatible charger.
Sent from my GT-I9003 using XDA Free mobile app
For now i would suggest you to
Perform a clean install and flash stock firmware (you can find it on sammobile website - requires registration).
Clean Install Step by Step:
1) Remove SD Card
2) Reboot your device in CWM Recovery Mode.
(If CWM is not there; flash CF-Root)
Select: "Advanced" and Erase Dalvik Cache.
Go back and Select: "Mounts and Storage"
And Format:
- Data
- System
- Boot
- Cache
After that Power Off your device and boot into download mode.
Open Odin; plug the USB Cable; select the firmware file under "PIT"
Press start; and wait untill Odin says "Pass".
Note that 1st boot takes longer.
Also do not remove the cable utill Odin says "Pass"
Let me know how it went.
The charging issue on the car charger may be due to a broken pin or incompatible charger.
Sent from my GT-I9003 using XDA Free mobile app
Last edited:
auto factory reset problem
hello everyone
I dont if it has been stated earlier....if yes then pardon me and direct me to the thread
my problem is very weird
in my i9003.....all custom roms work without any prob...but when I try to flash stock rom DDLF2 of my indian firmware then it flashes via odin and shows pass but phone keeps on boot screen.....I tried factory reset but still same
I researched a bit and then after flashing ddlf2 firmware I directly flashed vurrut kernel onto it......dis way my ohine boots in stock DDLF2 firmware and everythung worls fine
BUT the real problem starts whenever I reboot....phone kinda resets itself....all apps corrupt and I hv to re install them....all settings are reverted back to stock
plz help me.....I am searching job and face probs many times due to this issue.....I hv to use custom rom for now neither any modded stock. ..but I want actual stock back
any help plzz
hello everyone
I dont if it has been stated earlier....if yes then pardon me and direct me to the thread
my problem is very weird
in my i9003.....all custom roms work without any prob...but when I try to flash stock rom DDLF2 of my indian firmware then it flashes via odin and shows pass but phone keeps on boot screen.....I tried factory reset but still same
I researched a bit and then after flashing ddlf2 firmware I directly flashed vurrut kernel onto it......dis way my ohine boots in stock DDLF2 firmware and everythung worls fine
BUT the real problem starts whenever I reboot....phone kinda resets itself....all apps corrupt and I hv to re install them....all settings are reverted back to stock
plz help me.....I am searching job and face probs many times due to this issue.....I hv to use custom rom for now neither any modded stock. ..but I want actual stock back
any help plzz
Greetings.
It is possible to format and resize manually. I just dont know how it would work on Samsung.
Although it seems you have installed a custom rom (wich can resize partitions) or you have flashed the wrong file with wrong size.
In this case you should try:
1) Download Stock firmware from Sammobile.
2) Use Odin to Flash it.
The partition will resize into its previous size.
Then install CWM; Prepare the device for a clean install and install your favourite rom.
Press Thank button if it helped you.
Sent from my GT-I9003 using XDA Free mobile app
It is possible to format and resize manually. I just dont know how it would work on Samsung.
Although it seems you have installed a custom rom (wich can resize partitions) or you have flashed the wrong file with wrong size.
In this case you should try:
1) Download Stock firmware from Sammobile.
2) Use Odin to Flash it.
The partition will resize into its previous size.
Then install CWM; Prepare the device for a clean install and install your favourite rom.
Press Thank button if it helped you.
Sent from my GT-I9003 using XDA Free mobile app
which file
im having a soft break after try to restore...
1. Download and run odin.
2. Check Re-Partition, Auto Reboot and F. Reset Time.
3. Click PIT button and select this file: latona_20110114.pit
4. Put your phone into download mode: Press Volume down + OK + Power.
5. Connect USB cable and the program will detect the phone's Com number.
6. Click Start button to download the PIT file to phone.
7. After it is Done Click on Reset button, then unselect Re-Partition box.
8. Click PDA button and select this file: I9003xxxxx-xxx...-PDA-low-CL890053.tar.md5
9. Click PHONE button and select this file: MODEM_I9003xxxxx_REV_00_CL889972.tar.md5
10. Click CSC button and select this file: GT-I9003-CSC-xxxxxx.tar.md5
11. Remove the battery, then enter Device into Download Mode again.
12. Click Start button to flash these files to phone.
13. Do not touch anything till you see PASS on the program window.
14. Just do a factory reset after flashing using recovery
i've follow those instruction but not stuck at no8. because dont know which files need to select... picture below
1st one(RED LINE) or the 2nd one (GREEN LiNE)?
im having a soft break after try to restore...
1. Download and run odin.
2. Check Re-Partition, Auto Reboot and F. Reset Time.
3. Click PIT button and select this file: latona_20110114.pit
4. Put your phone into download mode: Press Volume down + OK + Power.
5. Connect USB cable and the program will detect the phone's Com number.
6. Click Start button to download the PIT file to phone.
7. After it is Done Click on Reset button, then unselect Re-Partition box.
8. Click PDA button and select this file: I9003xxxxx-xxx...-PDA-low-CL890053.tar.md5
9. Click PHONE button and select this file: MODEM_I9003xxxxx_REV_00_CL889972.tar.md5
10. Click CSC button and select this file: GT-I9003-CSC-xxxxxx.tar.md5
11. Remove the battery, then enter Device into Download Mode again.
12. Click Start button to flash these files to phone.
13. Do not touch anything till you see PASS on the program window.
14. Just do a factory reset after flashing using recovery
i've follow those instruction but not stuck at no8. because dont know which files need to select... picture below
1st one(RED LINE) or the 2nd one (GREEN LiNE)?
I couldt see the pic and didn't understand what's exactly the problem.
But if the issue is the file is easy to solve.
Assuming you Extracted your files to a folder...
Inside the folder you have about 5/6 files (more or less)
I.e: Modem; PDA; CSC; PIT etc.
So using process of exclusion, just take note of what files you have inside the folder and compare with the ones loaded into Odin and see wich file was not loaded.
Then load the file left in the last missing file to load.
You may also post the filename and the last missing part (in Odin) here before you flash. So we can see if you're going in the right direction.
--- --- ---
Besides that all the files (at least the ones I have) are identified except 1.
That will cross with the last 2 load buttons (in Odin) on the bottom.
If im not mistaken: Modem and CSC
--- --- ---
If you're experiencing a boot loop or a stop at boot.
Follow the instructions on how to install cwm (if you haven't flashed it yet); then clean caches and perform a soft reset.
This is what I do in those situations, and usually works 80% of times
Hit thanks if it helped you.
Sent from my GT-I9003 using XDA Free mobile app.
But if the issue is the file is easy to solve.
Assuming you Extracted your files to a folder...
Inside the folder you have about 5/6 files (more or less)
I.e: Modem; PDA; CSC; PIT etc.
So using process of exclusion, just take note of what files you have inside the folder and compare with the ones loaded into Odin and see wich file was not loaded.
Then load the file left in the last missing file to load.
You may also post the filename and the last missing part (in Odin) here before you flash. So we can see if you're going in the right direction.
--- --- ---
Besides that all the files (at least the ones I have) are identified except 1.
That will cross with the last 2 load buttons (in Odin) on the bottom.
If im not mistaken: Modem and CSC
--- --- ---
If you're experiencing a boot loop or a stop at boot.
Follow the instructions on how to install cwm (if you haven't flashed it yet); then clean caches and perform a soft reset.
This is what I do in those situations, and usually works 80% of times
Hit thanks if it helped you.
Sent from my GT-I9003 using XDA Free mobile app.
Last edited:
can't install any ROM....!!
hey, i am new to android. Just got an old Samsung galaxy sl gt-i9003. it has never been rooted. i tried rooting it using odin and the cf root file by LoLaTiOn for DDMF1 firmware. Did everything correctly and when it came to install zip from sd card, it gave an error after i selected the zip file. the error says- can't open E:/(name_of_the_ROM).zip (bad). I thought the problem might be with the zip file. but i tried a lot of ROMs like CM11 and Nameless but still the same error. please help me. i can't figure out what is the problem. :confuse: how can i install the ROM properly without any error?.
CF-ROOT file i used by LoLaTiOn: http://xdaforums.com/showpost.php?p=43016372&postcount=30
My phone details:
hey, i am new to android. Just got an old Samsung galaxy sl gt-i9003. it has never been rooted. i tried rooting it using odin and the cf root file by LoLaTiOn for DDMF1 firmware. Did everything correctly and when it came to install zip from sd card, it gave an error after i selected the zip file. the error says- can't open E:/(name_of_the_ROM).zip (bad). I thought the problem might be with the zip file. but i tried a lot of ROMs like CM11 and Nameless but still the same error. please help me. i can't figure out what is the problem. :confuse: how can i install the ROM properly without any error?.
CF-ROOT file i used by LoLaTiOn: http://xdaforums.com/showpost.php?p=43016372&postcount=30
My phone details:
Last edited:
How to run odin on Windows 8.1?
I recently upgraded to Windows 8.1. I installed Samsung drivers and Kies too. But odin doesn't recognise my phone. Any suggestions?
I recently upgraded to Windows 8.1. I installed Samsung drivers and Kies too. But odin doesn't recognise my phone. Any suggestions?
Similar threads
Top Liked Posts
-
There are no posts matching your filters.
-
3
to flash the theme
-you must be deodexed
-to deodex go to this link
http://xdaforums.com/showthread.php?t=1323661
-download deodex_ddkp2_cwm.zip
-put it in your sd card
-go to recovery(either by going to cwm app n select reboot into recovery or power off the device and press vol up+home key+power key)
-select install from zip (using volume keys and menu key)
-choose install zip from sd card
-select the deodex_ddkp2_cwm.zip theme zip
-it will ask for confirmation press yes
-select wipe cache and select yes
-download the theme file(it will be a zip file)
-put the zip file in the sd card
-go to recovery(either by going to cwm app n select reboot into recovery or power off the device and press vol up+home key+power key)
-select install from zip (using volume keys and menu key)
-choose zip from sd card
-select the ics theme zip
-it will ask for confirmation press yes
-go back and select wipe cache
-press yes and reboot
and you are done(same procedure for all themes)2
1. Yes
2. Yes
3. Find in the forum. You will get a thread related to it.
4. Actually kpe firmware contains all 4 files which is normally included in any firmware. We always need modem, bootloader files for flashing which lacks in newer firmwares i.e. kph, kpm. So we need kpe as a base.2
Use titanium backup to batch backup all your apps. After that, if u want to backup contacts and SMS, search the market. Then restore after flashing. Make sure you select the backup folder to the external SD card.
Cheers
Sent from my GT-i9003 powered by MIUI2
Download archive for your firmware. Extract it. Go to system/app and search application you need. I don't remember it's name. May be "route6"
---------- Post added at 11:20 PM ---------- Previous post was at 11:12 PM ----------
edit /etc/apt/sources.list
and add
===========
deb http://archive.canonical.com/ubuntu/ jaunty partner
===========
But I suggest you to update to 10.04 LTS. 9.04 is not supported now but 10.04 yes.
Also because of new License of Java from Oracle, the new packages of sun-java were removed from repositories (in 11.10 there is no sun-java even in partner repo)2Nobody seems to be answered my question here, whereas make a new thread seems promising but that's against the rule...
I have my unit for about 3 months already and if my memory serves me right. I think i have flashed it for more than ten times already. And as of now i don't see any problem so far.
