*****************************************************************************
XDA-Developers HTC KAISER CID Unlocker by pof
HTC TyTN II P4550 / T-Mobile MDA Vario III / AT&T Tilt (8900, 8915, 8925)
Swisscom XPA 1605 / Vodafone v1615 / Vodafone VPA Compact V / SFR v1615
Features:
1. SuperCID / Security Level=0 2. Does not check NBH signatures
3. Model ID check only 4 bytes 4. Based on MFG bootloader, rtask enabled
5. Accept any password 6. SPL overwrite disabled
This software is free to use but at your own risk, I take no responsiblity
for any conflict, fault, or damage caused by this unlocking procedure.
No warranties of any kind are given, any commercial use is prohibited.
Your donation is a strong incentive to continue research on new devices,
if you find my work useful please cosider making a PayPal donation to:
pau@eslack.org
Any donation amount is greatly appreciated
*****************************************************************************
Please make sure ActiveSync is enabled (GREEN icon in systray)
and hit ENTER to start...
Kaiser JumpSPL is running on your device, please check your device
screen and follow the steps until you see the tri-color screen.
When done hit ENTER to continue...
Device screen should be now TRI-COLOR and show "USB"
===> PLEASE UNPLUG AND RE-PLUG THE USB CABLE NOW <===
===> PLEASE UNPLUG AND RE-PLUG THE USB CABLE NOW <===
===> PLEASE UNPLUG AND RE-PLUG THE USB CABLE NOW <===
ActiveSync icon should become gray after that.
When done hit ENTER to continue...
Phone screen should now be tri-color and the activesync icon gray
if not, the loading process has failed and you'll have to repeat it again.
If all was OK hit ENTER and the standard "PDA Phone ROM Update Utility"
window will start, allowing you to flash HardSPL on your device.
Hit CTRL+C to Cancel or ENTER to continue...
Follow the steps on the wizard to flash HardSPL, when finished your
device will reboot. It should last no more than 1 minute.
- Launching RUU, please wait...
Process is finished, congratulations!
If you find it useful don't forget to donate
*****************************************************************************
(c)2007 pof - XDA Developers
Hit ENTER to quit.
Trying to flash HardSPL to my new tytn. However I keep getting this error message and the programme will not continue.
Any suggestions
Uhm... I do want to follow the directions explicitly,
Device screen should be now TRI-COLOR and show "USB"
===> PLEASE UNPLUG AND RE-PLUG THE USB CABLE NOW <===
===> PLEASE UNPLUG AND RE-PLUG THE USB CABLE NOW <===
===> PLEASE UNPLUG AND RE-PLUG THE USB CABLE NOW <===
Is this repeated for emphasis, or is one supposed to do this three times?
And.... why is this process so much more convoluted than flashing Hard SPL 2.10 Olipro on the 8525? Is it because the Kaiser is still new and the simplified process has not yet been created?
You need do it only once
You need do it cause the process executes the SSPL on the Kaiser, and the unplug/replug is needed to allow the OS on your PC to install the correct drivers, to be sure the process can follow, and warraty the success on HardSPL flash.
The process is basic the same as in Hermes HardSPL, with the unplug/replug step
Cheers.
*****************************************************************************
XDA-Developers HTC KAISER CID Unlocker by pof
HTC TyTN II P4550 / T-Mobile MDA Vario III / AT&T Tilt (8900, 8915, 8925)
Swisscom XPA 1605 / Vodafone v1615 / Vodafone VPA Compact V / SFR v1615
Features:
1. SuperCID / Security Level=0 2. Does not check NBH signatures
3. Model ID check only 4 bytes 4. Based on MFG bootloader, rtask enabled
5. Accept any password 6. SPL overwrite disabled
This software is free to use but at your own risk, I take no responsiblity
for any conflict, fault, or damage caused by this unlocking procedure.
No warranties of any kind are given, any commercial use is prohibited.
Your donation is a strong incentive to continue research on new devices,
if you find my work useful please cosider making a PayPal donation to:
pau@eslack.org
Any donation amount is greatly appreciated :-)
*****************************************************************************
Please make sure ActiveSync is enabled (GREEN icon in systray)
and hit ENTER to start...
Kaiser JumpSPL is running on your device, please check your device
screen and follow the steps until you see the tri-color screen.
When done hit ENTER to continue...
Device screen should be now TRI-COLOR and show "USB"
===> PLEASE UNPLUG AND RE-PLUG THE USB CABLE NOW <===
===> PLEASE UNPLUG AND RE-PLUG THE USB CABLE NOW <===
===> PLEASE UNPLUG AND RE-PLUG THE USB CABLE NOW <===
ActiveSync icon should become gray after that.
When done hit ENTER to continue...
Phone screen should now be tri-color and the activesync icon gray
if not, the loading process has failed and you'll have to repeat it again.
If all was OK hit ENTER and the standard "PDA Phone ROM Update Utility"
window will start, allowing you to flash HardSPL on your device.
Hit CTRL+C to Cancel or ENTER to continue...
Follow the steps on the wizard to flash HardSPL, when finished your
device will reboot. It should last no more than 1 minute.
- Launching RUU, please wait...
Process is finished, congratulations!
If you find it useful don't forget to donate :)
*****************************************************************************
(c)2007 pof - XDA Developers
Hit ENTER to quit.