FORUMS
Remove All Ads from XDA

[GUIDE] Z Ultra and Z1 HARD BRICK RECOVERY

510 posts
Thanks Meter: 996
 
By Doom Slayer, Senior Member on 13th February 2014, 12:15 AM
Post Reply Email Thread
6th September 2017, 09:35 AM |#711  
Junior Member
Thanks Meter: 0
 
More
Help please. My phone xperia z1 is not detected by any flashtool or in the device manager. My phone was left uncharged for several months, when i tried to charge it, it just show a solid red led, not blinking so i thought maybe the battery is dead so i bought a new battery and replaced the old one, but still the same, cannot be on, cannot be detected by pc, when I connect to the charger it just show a solid red led. I tried all the button combination.
 
 
10th December 2017, 04:44 AM |#712  
Junior Member
Flag WeiFang
Thanks Meter: 0
 
More
Do you have sin set file for sol24?(z ultra Japan AU KDDI version)
recently I bought a second hand sony sol24,which was unable to turn on or entre the flash mode because the previous user turn off the power while flashing.
now the indicator light goes red blink when plug in the charger or connected to computer with the data cable.
I wanna try to fix it with S1tool.
but it seems the phone never had trim aera backup.
thanks a lot.
10th March 2018, 11:28 PM |#713  
Junior Member
Thanks Meter: 0
 
More
sa z5 hard brick s1 boot help me
Welcome to S1 tool.
That is small and crippled subset of SETOOL2 service tool.

SELECT FIRMWARE PACKAGES
YOU CAN SELECT SEVERAL PACKAGES WITH CTRL BUTTON
CHECKING PACKAGES ...

DETACH USB CABLE FROM PHONE
REMOVE BATTERY FROM PHONE
ATTACH TESTPOINT
PRESS "READY", THEN ATTACH USB CABLE TO PHONE

will use Sahara protocol ...
REMOVE TESTPOINT NOW, THEN PRESS "READY"

PROCESSING ...
SERIAL NUMBER : 13484502
HARDWARE ID : 04000100E1009400
HASH :F421B16FFDD52124A7107C2156B6C478355991BC9D88F0F86 82CD08F127A0FA5
HARDWARE ID 04000100E1009400 NOT SUPPORTED
Elapsed:27 secs.

SELECT FIRMWARE PACKAGES
YOU CAN SELECT SEVERAL PACKAGES WITH CTRL BUTTON
CHECKING PACKAGES ...

DETACH USB CABLE FROM PHONE
REMOVE BATTERY FROM PHONE
ATTACH TESTPOINT
PRESS "READY", THEN ATTACH USB CABLE TO PHONE

PROCEDURE STOPPED BY USER
Elapsed:19 secs.

SELECT FIRMWARE PACKAGES
YOU CAN SELECT SEVERAL PACKAGES WITH CTRL BUTTON
CHECKING PACKAGES ...

DETACH USB CABLE FROM PHONE
REMOVE BATTERY FROM PHONE
ATTACH TESTPOINT
PRESS "READY", THEN ATTACH USB CABLE TO PHONE

will use Sahara protocol ...
REMOVE TESTPOINT NOW, THEN PRESS "READY"

PROCESSING ...
llbug: write error: "Aygıt komutu algılayamıyor"
llbug: blk write fail.fatal
Elapsed:24 secs.

SELECT FIRMWARE PACKAGES
YOU CAN SELECT SEVERAL PACKAGES WITH CTRL BUTTON
CHECKING PACKAGES ...

DETACH USB CABLE FROM PHONE
REMOVE BATTERY FROM PHONE
ATTACH TESTPOINT
PRESS "READY", THEN ATTACH USB CABLE TO PHONE

will use Sahara protocol ...
REMOVE TESTPOINT NOW, THEN PRESS "READY"

PROCESSING ...
SERIAL NUMBER : 13484502
HARDWARE ID : 04000100E1009400
HASH :F421B16FFDD52124A7107C2156B6C478355991BC9D88F0F86 82CD08F127A0FA5
HARDWARE ID 04000100E1009400 NOT SUPPORTED
Elapsed:147 secs.

SELECT FIRMWARE PACKAGES
YOU CAN SELECT SEVERAL PACKAGES WITH CTRL BUTTON
CHECKING PACKAGES ...

DETACH USB CABLE FROM PHONE
REMOVE BATTERY FROM PHONE
ATTACH TESTPOINT
PRESS "READY", THEN ATTACH USB CABLE TO PHONE

will use Sahara protocol ...
REMOVE TESTPOINT NOW, THEN PRESS "READY"

PROCESSING ...
llbug: write error: "Aygıt komutu algılayamıyor"
llbug: blk write fail.fatal
Elapsed:77 secs.

SELECT FIRMWARE PACKAGES
YOU CAN SELECT SEVERAL PACKAGES WITH CTRL BUTTON
CHECKING PACKAGES ...

DETACH USB CABLE FROM PHONE
REMOVE BATTERY FROM PHONE
ATTACH TESTPOINT
PRESS "READY", THEN ATTACH USB CABLE TO PHONE

will use Sahara protocol ...
REMOVE TESTPOINT NOW, THEN PRESS "READY"

PROCESSING ...
SERIAL NUMBER : 13484502
HARDWARE ID : 04000100E1009400
HASH :F421B16FFDD52124A7107C2156B6C478355991BC9D88F0F86 82CD08F127A0FA5
HARDWARE ID 04000100E1009400 NOT SUPPORTED
Elapsed:18 secs.

SELECT FIRMWARE PACKAGES
YOU CAN SELECT SEVERAL PACKAGES WITH CTRL BUTTON
CHECKING PACKAGES ...

DETACH USB CABLE FROM PHONE
REMOVE BATTERY FROM PHONE
ATTACH TESTPOINT
PRESS "READY", THEN ATTACH USB CABLE TO PHONE

will use Sahara protocol ...
REMOVE TESTPOINT NOW, THEN PRESS "READY"

PROCESSING ...
SERIAL NUMBER : 13484502
HARDWARE ID : 04000100E1009400
HASH :F421B16FFDD52124A7107C2156B6C478355991BC9D88F0F86 82CD08F127A0FA5
HARDWARE ID 04000100E1009400 NOT SUPPORTED
Elapsed:22 secs.

SELECT FIRMWARE PACKAGES
YOU CAN SELECT SEVERAL PACKAGES WITH CTRL BUTTON
CHECKING PACKAGES ...

DETACH USB CABLE FROM PHONE
REMOVE BATTERY FROM PHONE
ATTACH TESTPOINT
PRESS "READY", THEN ATTACH USB CABLE TO PHONE

PROCEDURE STOPPED BY USER
Elapsed:99 secs.

SELECT FIRMWARE PACKAGES
YOU CAN SELECT SEVERAL PACKAGES WITH CTRL BUTTON
CHECKING PACKAGES ...

DETACH USB CABLE FROM PHONE
REMOVE BATTERY FROM PHONE
ATTACH TESTPOINT
PRESS "READY", THEN ATTACH USB CABLE TO PHONE

will use Sahara protocol ...
REMOVE TESTPOINT NOW, THEN PRESS "READY"

PROCESSING ...
SERIAL NUMBER : 13484502
HARDWARE ID : 04000100E1009400
HASH :F421B16FFDD52124A7107C2156B6C478355991BC9D88F0F86 82CD08F127A0FA5
HARDWARE ID 04000100E1009400 NOT SUPPORTED
Elapsed:91 secs.
13th May 2018, 12:53 PM |#714  
Junior Member
developer's world
Thanks Meter: 0
 
More
Loader not responding
Hi, can anyone clarify what does this code mean ? LOADER AID: 0004 or why this loader may not responding ?

Code:
RUNNING S1_PRELOADER VER "LOADER_RELEASE_MSM8974_23_4_AID_4"
LOADER AID: 0004
can't get S1 command header
LOADER NOT RESPONDING
Elapsed:57 secs.
well...

What commands will be pushed for initializing after sending ? Does available any source code for s1tools ?

Does exist any way to execute custom bootloader like u-boot etc. ?
Mainly what's the problem and what to do for this case. I mean from what to start o_o

By the way, initially I used GND from usb connector on board, but now [ SOMC Flash Device ] always is activated after connecting without test-point and without battery of course. Any idea ?

Quote:
Originally Posted by munjeni

If you have ta backup (TA.img) from your phone than you can try with this http://forum.xda-developers.com/show...&postcount=314 it is for z1c but I am sure it will work too for your model (but please open syn file set archive after tool generate them for you, to be sure custom-reset.ta is not blank or probably with some stupid data!)

I have TA but I can't get S1 command header as you can see above. Do you know what's problem may be for this ? Thanks.

-----
upd: hmm, just noticed postfix - '...MSM8974_23_4_AID_4' but, what's wrong with loader :( where are you o_O
p.s: z ultra C6833 is not mine, however will be good to fix this anyway :)
17th May 2018, 10:02 PM |#715  
Senior Member
Thanks Meter: 7
 
More
My phone is xa1 plus please help to me my phone is just red light when connect to usb but not reset with power + up volume
27th June 2018, 10:43 AM |#716  
Junior Member
Thanks Meter: 0
 
More
i havesame problem somc flash mode in e1 dual plz help me
1st July 2018, 02:39 AM |#717  
Member
Thanks Meter: 2
 
More
Hi everybody. My Z Ultra was bricked after I accidentally connected a cheap OEM magnetic charger the wrong way round ("reverse charging" - I'm not the first person to do it)

https://forum.xda-developers.com/xpe...arger-t2806392

Power button produced a vibration. Power and volume down produced an Xperia splash screen and nothing else. I removed the battery and charged it for about 45 minutes directly at the terminals. I followed the steps in the OP and it didn't work. The readout says:

SELECT FIRMWARE PACKAGES
YOU CAN SELECT SEVERAL PACKAGES WITH CTRL BUTTON
CHECKING PACKAGES ...

DETACH USB CABLE FROM PHONE
REMOVE BATTERY FROM PHONE
ATTACH TESTPOINT
PRESS "READY", THEN ATTACH USB CABLE TO PHONE

will use Sahara protocol ...
REMOVE TESTPOINT NOW, THEN PRESS "READY"

PROCESSING ...
SERIAL NUMBER : 6ED79402
HARDWARE ID : 04000100E1007B00
HASH :49109A8016C239CD8F76540FE4D5138C87B2297E49C6B30EC 31852330BDDB177
Emergency loader uploaded ...

RUNNING S1_PRELOADER VER "LOADER_RELEASE_MSM8974_23_4_AID_4"
LOADER AID: 0004
DEVICE ID: 0294D76E
FLASH ID: "0015/01000001"
LOADER VERSION: "LOADER_RELEASE_MSM8974_23_4_AID_4"

WRITING PACKAGES ...
Processing package
C:\Users\Daniel\Desktop\C6806\14_2_A_0_290.APP_SW_ Togari_GENERIC_1271_5715_S1_SW_LIVE_6732_PID1_0005 _MMC.SIN_FILE_SET

WILL UPDATE BOOT TO : 1270-3115 S1_BOOT_MSM8974_LA1.04_15
PARSING: "DEVELOPMENT"
value OTP_LOCK_STATUS_1 : UNLOCKED, not match LOCKED
PARSING: "TEST_OEM0_007B00E1"
value OTP_LOCK_STATUS_1 : LOCKED, match LOCKED
value OTP_DATA_1 : 00000100, not match 01000400
value IDCODE_1 : 007B00E1, match 007B00E1
PARSING: "PRECOMMERCIAL_007B00E1"
value OTP_LOCK_STATUS_1 : LOCKED, match LOCKED
value OTP_DATA_1 : 01000400, match 01000400
value IDCODE_1 : 007B00E1, match 007B00E1
PROCESSING : dbi_S1_Boot_MSM8974_LA1_04_15_AID_4_S1-SDI2-6732-PID1-0004-SDI_S1-BOOT-6732-0004-MMC.sin
PROCESSING : emmc_appsboot_S1_Boot_MSM8974_LA1_04_15_AID_4_PLAT FORM-MSM8974-LIVE-HWID007B00E1-SWID09-OEM1-AID4-DEBUG00_S1-BOOT-6732-0004-MMC.sin
PROCESSING : s1sbl_S1_Boot_MSM8974_LA1_04_15_AID_4_PLATFORM-MSM8974-LIVE-HWID007B00E1-SWID65-OEM1-AID4-DEBUG00_S1-BOOT-6732-0004-MMC.sin
PROCESSING : sbl1_S1_Boot_MSM8974_LA1_04_15_AID_4_PLATFORM-MSM8974-LIVE-HWID007B00E1-SWID00-OEM1-AID4-DEBUG00_S1-BOOT-6732-0004-MMC.sin
PROCESSING : tz_S1_Boot_MSM8974_LA1_04_15_AID_4_PLATFORM-MSM8974-LIVE-HWID007B00E1-SWID07-OEM1-AID4-DEBUG00_S1-BOOT-6732-0004-MMC.sin
PROCESSING : Togari_S1BootConfig_MiscTA_130115_1430.ta
MINOR ERROR [ Open_TA_failed, err: 001D ]
BOOT UPDATED
Processing ACPU files
PROCESSING: cache_S1-SW-LIVE-6732-PID1-0005-MMC.sin
PROCESSING: apps_log_S1-SW-LIVE-6732-PID1-0005-MMC.sin
PROCESSING: kernel_S1-SW-LIVE-6732-PID1-0005-MMC.sin
PROCESSING: fotakernel_S1-SW-LIVE-6732-PID1-0005-MMC.sin
SKIP: partition-image_S1-SW-LIVE-6732-PID1-0005-MBR.sin
PROCESSING: rpm_S1-RPMFW-LIVE-6732-PID1-0005-MMC.sin
no update files in package
FINISHED
Elapsed:130 secs.

What's the problem? Is it just a hardware problem?
24th July 2018, 10:27 PM |#718  
Junior Member
Thanks Meter: 0
 
More
So, from what i've understood;
If my TA is damaged, theres no way im gonna get my Z1 to work again?
Post Reply Subscribe to Thread

Guest Quick Reply (no urls or BBcode)
Message:
Previous Thread Next Thread
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes