[RECOVERY]Clockwork Touch Recovery 5.8.2.1 by JvS CoRp V5 TF101\G

Search This thread

jvscorp

Member
Feb 1, 2008
16
121
ClockworkMod Touch Recovery 5.8.2.1 by JvS CoRp V5



ChangeLog
V1
Installation Error Fixed
V2
Reboot Loop Fixed
Internal memory install only
V3
Minor Fixes for improve performance
Still Internal Memory
V4
New Version 5.8.1.9
Improve performance
V5
New Version 5.8.2.1
LINK Removed
Work on it



Installation:

Just flash the attached zip from internal memory with 5.5.0.4 .
Tested on TF101G B80 con CM9




For change CWM download and install Recovery Installer APK and run.

:mad:Thanks Button is not cost nothing Use it:mad:
Usual disclaimer applies: if you brick your tablet, it's not my problem!
Thanks all Android Community.
 

Attachments

  • IMG-20120402-00016.jpg
    IMG-20120402-00016.jpg
    173.6 KB · Views: 4,936
  • IMG-20120402-00013.jpg
    IMG-20120402-00013.jpg
    174.1 KB · Views: 4,495
  • RecoveryInstaller.apk
    4.3 MB · Views: 10,707
  • Clockwork_Recovery_5.8.1.9_by_JvS_Corp_V4.zip
    5.1 MB · Views: 8,532
Last edited:

kay_kiat88

Senior Member
Dec 19, 2010
889
246
ClockworkMod Recovery touch 5.8.1.8 for TF101 \G by JvS CoRp Original

Installation:

Just flash the attached zip from CWM.




Usual disclaimer applies: if you brick your tablet, it's not my problem!

I see you have been lurking around here for 4 years lol.. does this cwm allow flashing from both internal and external sd? great work and thanks. haven't tried it though.
 
  • Like
Reactions: seriouser

gunz.jones

Senior Member
Nov 6, 2010
1,238
220
Athens, TX
Kept getting parse error and wouldn't install (STATUS 6). Redownloading and will report back.

Edit: Booted back to CWM with a few fresh d/ls. Same error. Line 1 of 56 is BAD.

Sent from my Transformer TF101 using xda premium
 
Last edited:

dangambino

Senior Member
Feb 2, 2010
680
99
baltimore
same issue as the last official cloclwork release. will not reboot. always bqck to recovery. roach please work ur magic. thnx in advance ;)
 
  • Like
Reactions: jvscorp

SWEagle

Senior Member
Nov 16, 2011
321
62
Machico
Running fine now. It would be great if it had the micro SD support...

---------- Post added at 06:25 PM ---------- Previous post was at 06:08 PM ----------

Spoke too soon... It's rebooting into recovery...

I have Rogue CWM in the system memory and i tried to install over this one and didn't work... it goes back again into recovery. Anybody as any idea on how i can get in the OS? or copy Roach CWM in to the system memory?

Any help would be appreciated...
 

hachamacha

Senior Member
Jun 15, 2010
1,368
751
Honor 8
Since people are so interested in touch recovery and especially any recovery with MicroSD support and /sdcard support, then I wonder if anyone has based their take on this on the working MicroSD/Internal version (as linked to by this):

https://github.com/rburrow87/android_device_asus_tf101_recoveryonly

I am guessing that if you know how to add the touch logic to recovery then you might be able to add very similar logic (nothing is ever the same) to this working version I linked to.

It seems odd that people are developing without using both internal and external storage but all work is appreciated.
 
  • Like
Reactions: jvscorp

SWEagle

Senior Member
Nov 16, 2011
321
62
Machico
Managed to get in the OS but i tried to install Roach and Rogue CWM over this one and it doesn't install... always comes up the same...


Any ideas?
 

baseballfanz

Senior Member
Oct 19, 2010
6,829
1,702
Sugar Land TX
Samsung Galaxy A52 5G
Managed to get in the OS but i tried to install Roach and Rogue CWM over this one and it doesn't install... always comes up the same...


Any ideas?

After you have flash a different recovery DO NOT use the Boot into system.
Instead cold boot into the OS and use Terminal Emulator to type in the following command.

Type : su (give permission if ask, choose YES). You should get a #
Type : echo boot | dd of=/dev/block/mmcblk0p3 bs=1 seek=0
Type : exit
Type : reboot

Note: Hit "Enter" after each line
 
  • Like
Reactions: cvs0115 and jvscorp

SWEagle

Senior Member
Nov 16, 2011
321
62
Machico
After you have flash a different recovery DO NOT use the Boot into system.
Instead cold boot into the OS and use Terminal Emulator to type in the following command.

Type : su (give permission if ask, choose YES). You should get a #
Type : echo boot | dd of=/dev/block/mmcblk0p3 bs=1 seek=0
Type : exit
Type : reboot

Note: Hit "Enter" after each line


Thanks you very much for you response...

Me and a friend of mine use this adb command to stop the bootloot and with this it reach the point of the CWM instalation... now it's working fine...

Type: adb shell dd if=/dev/zero of=/dev/block/mmcblk0p3
 
  • Like
Reactions: gsharrison

Top Liked Posts

  • There are no posts matching your filters.
  • 118
    ClockworkMod Touch Recovery 5.8.2.1 by JvS CoRp V5



    ChangeLog
    V1
    Installation Error Fixed
    V2
    Reboot Loop Fixed
    Internal memory install only
    V3
    Minor Fixes for improve performance
    Still Internal Memory
    V4
    New Version 5.8.1.9
    Improve performance
    V5
    New Version 5.8.2.1
    LINK Removed
    Work on it



    Installation:

    Just flash the attached zip from internal memory with 5.5.0.4 .
    Tested on TF101G B80 con CM9




    For change CWM download and install Recovery Installer APK and run.

    :mad:Thanks Button is not cost nothing Use it:mad:
    Usual disclaimer applies: if you brick your tablet, it's not my problem!
    Thanks all Android Community.
    3
    Go back a few posts.

    After you have flash a different recovery DO NOT use the Boot into system.
    Instead cold boot into the OS and use Terminal Emulator to type in the following command.

    Type : su (give permission if ask, choose YES). You should get a #
    Type : echo boot | dd of=/dev/block/mmcblk0p3 bs=1 seek=0
    Type : exit
    Type : reboot

    Note: Hit "Enter" after each line
    This didn't work for me so I took out the exit command and it worked perfectly.. basically this

    After you have flash a different recovery DO NOT use the Boot into system.
    Instead cold boot into the OS and use Terminal Emulator to type in the following command.

    Type : su (give permission if ask, choose YES). You should get a #
    Type : echo boot | dd of=/dev/block/mmcblk0p3 bs=1 seek=0
    Type : reboot

    Note: Hit "Enter" after each line


    Weird huh? I tried your original instructions about 16 times the last three days and was frustrated.. tried it without and it worked the first time.

    Even weirder was I flashed gee one's stock rom and recovery and that worked but just boot looped Roach's CWM repack that came with the rom. I then did my method and viola.. All good.
    2
    Managed to get in the OS but i tried to install Roach and Rogue CWM over this one and it doesn't install... always comes up the same...


    Any ideas?

    After you have flash a different recovery DO NOT use the Boot into system.
    Instead cold boot into the OS and use Terminal Emulator to type in the following command.

    Type : su (give permission if ask, choose YES). You should get a #
    Type : echo boot | dd of=/dev/block/mmcblk0p3 bs=1 seek=0
    Type : exit
    Type : reboot

    Note: Hit "Enter" after each line
    1
    ClockworkMod Recovery touch 5.8.1.8 for TF101 \G by JvS CoRp Original

    Installation:

    Just flash the attached zip from CWM.




    Usual disclaimer applies: if you brick your tablet, it's not my problem!

    I see you have been lurking around here for 4 years lol.. does this cwm allow flashing from both internal and external sd? great work and thanks. haven't tried it though.
    1
    I'm looking forward to trying this.