FORUMS
Remove All Ads from XDA

[RADIO] [WIKI] Blackstone Radios - Updated 15 September 1.17.25.09

2,456 posts
Thanks Meter: 49
 
By HDuser, Retired Moderator on 1st January 2009, 12:07 PM
Post Reply Email Thread
WIKI Page for Radio Flashing here

Wiki Version Page http://wiki.xda-developers.com/index...stone_Versions

BLACKSTONE RADIOS - All of these radios have been tested and work. I highly advise flashing radio's via MicroSD card.

Credit to duttythroy-
FAQ: How to do a Rom/Radio Upgrade with SD Card..
Solution:
1.Copy BLACIMG.NBH into the root dir of your Storage Card.
2. Be sure to have at least 30% of charge.
3. Turn off your device by using the Power Button
4. Go to bootloader mode. Push and hold Vol Down + press Power button.
5. As soon as presented the message, push Power button to start flashing or Volume Down button to cancel.
6. The whole procedure will take about 3 minutes. After you finish and see the relative message, soft reset your device, you are ready.


1.09.25.14 / 52.49a.25.26W

Download 1.09.25.14 / 52.49a.25.26W Radio only Megepload
Download HD_Blackstone_Radio 1.09.25.14 (with RUU) 4shared

1.09.25.35 / 52.55b.25.28U

Download 1.09.25.35 / 52.55b.25.28U Radio Only - Duttythroy.net
Download 1.09.25.35 / 52.55b.25.28U Radio Only - 4Shared

1.10.25.25 / 52.57.25.30U

Download 1.10.25.25 / 52.57.25.30U Radio only Megaupload
Download 1.10.25.25 / 52.57.25.30U Radio only rapidshare
Download HD_Blackstone_Radio 1.10.25.25 (with RUU) 4shared

1.12.25.16 / 52.60.25.33

Download 1.12.25.16 / 52.60.25.33 Radio only - Rapidshare
Download 1.12.25.16 / 52.60.25.33 Radio only - 4Shared

1.13.25.24 / 52.62.25.34U

Download 1.13.25.24 / 52.62.25.34 Radio only - Rapidshare
Added BS_Rilphone.dll_1.13.25.24 to the bottom of this Post (sorry no cab, HDuser 5.4.2009)
Reports in the radio thread are made that this Dll does not work, so as always at your own risk
http://forum.xda-developers.com/show...496665&page=12

Radio 1.13.25.24 Thread http://forum.xda-developers.com/showthread.php?t=496665

1.14.25.24 / 52.64.25.34U

Radio 1.14.25.24 Thread http://forum.xda-developers.com/showthread.php?t=508232
Please post issues in that thread

1.17.25.09 / 52.69.25.37

Radio 1.17.25.09 Thread http://forum.xda-developers.com/showthread.php?t=560451

Blackstone Rilphone.dll Cabs

Credit to P1Tater for creating the cabs and to Chainfire for developing DriverWiz - Make signed CABs from driver DLLs that work

Understand, that if it doesn't work, a HR might be in your future. Please test at your own risk.

BS_Rilphone_1_08_25_23.cab
BS_Rilphone_1_09_25_23.cab
BS_Rilphone_1_09_25_24.cab
BS_Rilphone_1_10_25_25.cab
BS_Rilphone_1_12_25_16.cab
BS_Rilphone_1_13_25_24.cab
BS_Rilphone_1_14_25_24.cab
BS_Rilphone_1_15_25_14.cab


Installation method.
  1. Install the .cab that works with the radio you want to flash.
  2. Do not soft reset but turn off the device.
  3. Flash via MicroSD or via your PC in the bootloader.
  4. Finished!
The Following has been copied out of AllTheWay post http://forum.xda-developers.com/show...&postcount=365

I have been noticing in the Raphael community there has been a lot of talk of changing the rilphone.dll file when flashing to a new radio.
I was able to get a GPS signal lock with the radio and .dll file in under 10 seconds using first Quick GPS then loading up Google Maps. Calls are also very clear as well.
Currently I am using radio 1.12.25.16 with the rilphone.dll file that I downloaded from here.

If you would like to read more information on what the rilphone.dll does read this post by Da_G

Here is Microsoft's explanation of it



When a module first registers with the RIL, it passes in two callback functions. One is used for unsolicited notifications, and the other is used for responses to function calls. For example, when the phone receives a new incoming call, the RIL uses the unsolicited notification callback to notify each module about the incoming call.
When a module calls the RIL to get the signal strength, the function call immediately returns a response identifier. The RIL uses the function response callback to convey signal strength information to the module. To ensure that response callbacks are correctly matched with function calls, this callback structure also contains the same response identifier value that is returned by the original function call. This asynchronous architecture simplifies the RIL implementation. If a module needs to call a RIL function in a synchronous manner, it needs to make the function call and block until the module receives the function response callback.
1st January 2009, 01:09 PM |#2  
120.fr's Avatar
Junior Member
Flag Paris
Thanks Meter: 0
 
More
Hi,

Wiki page updated
download link for Radio 1.10.25.25 / 52.57.25.30u

Extract nbh & flash with Blackstone Custom RUU
No hard Reset needed but it's recommanded.


1st January 2009, 02:02 PM |#3  
Junior Member
Thanks Meter: 0
 
More
Any 1 tryed this new radio yet?
1st January 2009, 02:06 PM |#4  
OP Retired Moderator
Zürich, Switzerland
Thanks Meter: 49
 
More
not that I know of, I just updated the first page with a warning
1st January 2009, 02:25 PM |#5  
120.fr's Avatar
Junior Member
Flag Paris
Thanks Meter: 0
 
More
I'm actually running with this radio without problem for the moment.
No hard-Reset done after flash

Wiki Updated with Default Radio download link (1.09.25.14 / 52.49a.25.26W)
Attached Thumbnails
Click image for larger version

Name:	radio.png
Views:	6410
Size:	70.6 KB
ID:	141902  
1st January 2009, 02:48 PM |#6  
OP Retired Moderator
Zürich, Switzerland
Thanks Meter: 49
 
More
120.fr

Would you please fill out the section on how to extract a radio rom on our WIKI Page
1st January 2009, 03:21 PM |#7  
Junior Member
Thanks Meter: 0
 
More
Do you need to do HARD-SPL before flashing radio? Or we can flash
without HARD-SPL thing to do?
1st January 2009, 04:59 PM |#8  
stepw's Avatar
Senior Member
Thanks Meter: 16
 
More
Quote:
Originally Posted by gospodar34

Do you need to do HARD-SPL before flashing radio? Or we can flash without HARD-SPL thing to do?

You can't flash it without HSPL or USPL, unless you want to install full Arabic ROM and have a device with HTC__J15 CID.
1st January 2009, 05:50 PM |#9  
duttythroy's Avatar
Retired Moderator
Flag london
Thanks Meter: 947
 
Donate to Me
More
Quote:
Originally Posted by HDuser

WARNING This has not been tested by me so I can not say that it will work read the thread and try it at your own risk

Hi all

There is a new radio version around.

Wiki Version Page http://wiki.xda-developers.com/index...stone_Versions

Radio, Protocol Version
* 1.10.25.25 / 52.57.25.30U
* Found in RUU_BlackStone_HTC_ARA_1.14.415.2_Radio_52.57.25.3 0_1.10.25.25_Ship.exe
* Rom Thread http://forum.xda-developers.com/showthread.php?t=466173
* Radio Thread http://forum.xda-developers.com/showthread.php?t=466274

WIKI Page for Radio Flashing http://wiki.xda-developers.com/index...ackstone_Radio
This page needs to be updated

Have fun

WARNING This has not been tested by me so I can not say that it will work read the thread and try it at your own risk

Nice work, very good work ur doing and also allocating Roms to the WIKI
1st January 2009, 09:13 PM |#10  
troxter's Avatar
Senior Member
Flag London
Thanks Meter: 35
 
More
:)
Very good radio!!! Finally I don't have a problem with using 3G. Now is three bars of signal strenght in places where was two. Aslo, this radio fixed problem with "The person is temporary unavailable". For me working very fine. Now I can use 3G all the time.

Sorry for my English.
1st January 2009, 09:50 PM |#11  
uiqjirka's Avatar
Senior Member
Flag Prague
Thanks Meter: 40
 
More
Thumbs up
This radio works excelent,3G,HSDPA.Thanks
Post Reply Subscribe to Thread

Guest Quick Reply (no urls or BBcode)
Message:
Previous Thread Next Thread
Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes