any one who know jtag see this picture to M.R Orefkov see this because i have wrong

[dvdaio]

plase from an one how know about jtag about htc p3400 guide me please

i want to know in this picture where is pin 14 go because it didn't appear good
and also the gns for this device where i must to put it
i have dead htc with wrong bootloader and i made all things to it now but jtag didn't detect my device

this is direct link to image
http://img269.imageshack.us/img269/9348/genep3400new.jpg
tell me where is pont 14 go and also the gnd for this phone where i must to put it

 

[vaibhav_batra_the_techguy]

Wires for JTAG interface MUST not be longer 20 - 25 cm !!!

Buy a LPT socket like this

and with the help of a multimeter chk all the pin connections...and solder required wires accordingly to different pins.

Then solder other end of wires to GENE

Put that wire set of pin no 14 & 18-25 to the Ground of the GENE PCB

And do not use USB while doing this

 

[dvdaio]

thanks alot my best frind but this socket lpt is male or female and the pin 14 and 18 to 25 with the ground oky i did that and i made also new board in elctronic shop to this jtag and the check for all connection is i must use batery or use power supplay when power up the phone with lpt and is there any settings in my pc to prepare it

Wires for JTAG interface MUST not be longer 20 - 25 cm !!!

Buy a LPT socket like this

and with the help of a multimeter chk all the pin connections...and solder required wires accordingly to different pins.

Then solder other end of wires to GENE

Put that wire set of pin no 14 & 18-25 to the Ground of the GENE PCB

And do not use USB while doing this

 

[vaibhav_batra_the_techguy]

u need male socket because PCs have LPT female sockets

something like this

i have seen many people in the mobile repairing shops flashing nokia phones without the battery
so the answer is NO, u dont need to use battery or some other power source
LPT will provide all the power needed

 

[dvdaio]

i made ALL things like you told me and tried to another pc my phone was didn't detect by h-jtag and the phone is powerd on boot loader mode now i want to know the reason my board is very googd quality that i made for this jtag and i checked for it before i take it and also the resistors are good so what is the reason now
[email protected]

 

[vaibhav_batra_the_techguy]

well if the phone booted with the help of LPT i.e. no external power source it means there is some other problem than connectivity...

contact orekfov or ramersonv, they may help/ guide u further

 

[dvdaio]

hi my best friend i have good news for you finally the jtag was worknig but now there

hi my best friend i have good news for you finally the jtag was worknig but now there another samll problem it is in this steps

Further we Choose item of menu Load
2) Necessarily the first we put a tick on Load as binary image
3) we Specify the address of loading in RAM 10000000
4) we Choose a file bootloader for loading spl.nb, we press Ok and we see progress a bar of loading (it is necessary to wait some time that was filled in the file).
5) As soon as it will be filled in a file we choose item of menu View and it is chosen by submenu Disassemble at...
6) 10000000 address necessary to us Is specified, we press Ok and we see code ARM - if all has passed well and the file is loaded that by the first command should be EA0003FE.
7) we Clamp button Camera Is chosen punkt menu RUN and to submenu Go FROM...
8) we Specify 10000000 address and is pressed Ok


Where i can find this choice because i made all settings in jtag my processor was shoing also without any problem but where is the choice to load bootloader file please is you can help me i am in the finally steps
[email protected]

 

[dvdaio]

Finally i made all thins now all things are oky but the last thing

FINALLY I MADE ALL THINS NOW ALL THINGS ARE OKY BUT THE LAST THING
AFTER THE FILE ARE LAODED MY DEVICE ALSO SHOW TO ME SPL 1.07 oref NOW WHAT IS THE PROBLEM IS THE FILE DIDN'T LOADED CORRECTLY OR WHAT
[email protected]

 

[vaibhav_batra_the_techguy]

now u need to flash a ROM

search the forum for ROMs for New GENE

BTW did u used for old Gene (SN - HT7x)?

FYI S.N doesnt matter in deciding whthr u hv new or Old GENE

 

[dvdaio]

my best frind finally i recoverd my device with jtag and all be oky but my device now is show imei as 004400XXXXXXX and now i want to recovers my original imei because when i pust sim on the device it told me data crashed so what is the solution now
[email protected]

 

[vaibhav_batra_the_techguy]

my best frind finally i recoverd my device with jtag and all be oky but my device now is show imei as 004400XXXXXXX and now i want to recovers my original imei because when i pust sim on the device it told me data crashed so what is the solution now
[email protected]

http://forum.xda-developers.com/showthread.php?t=274860

 

[dvdaio]

my best friend i have an error when i try to use this programe it gave me and error
(UNABLE TO COMPLETE THE HTC IMEI UPDATE WIZARD AND TELL ME YOU MUST HAVE CID UNLOCKED WHAT IS THAT MEAN ?????
[email protected]

 

[dvdaio]

this is the data but also the imei didn't changed
Old IMEI number:
C4BC6400C4BC640

New IMEI number:
353527020579491
also the old imei

 

[mailforkrishna]

Help please

my best frind finally i recoverd my device with jtag and all be oky but my device now is show imei as 004400XXXXXXX and now i want to recovers my original imei because when i pust sim on the device it told me data crashed so what is the solution now
[email protected]

Could you please explain the jtag method you followed to recover your gene it will help to save on of my friends Gene.
His phone is bricked.

 

[dvdaio]

oky pm me on yahoo
[email protected]
or on hotmail
[email protected]

 

[mailforkrishna]

Help

oky pm me on yahoo
[email protected]
or on hotmail
[email protected]

Have wrote on hotmail

 

[vaibhav_batra_the_techguy]

please elaborate the whole process in ur first post with possible screenshots....

this is gonna be sticky

 

[dvdaio]

oky now i prepared the screen shot for that to help all people who have this problem but the last problem with me is on change the imei for my device

 

[dvdaio]

please i want the lat thing that to repair my device i wnat to change my imei it is corrupted after that i can make a new thread to all people with the stps to help them
thanks i wait your reply
[email protected]

 

[Addicted2xda]

oky now i prepared the screen shot for that to help all people who have this problem but the last problem with me is on change the imei for my device

Please go to Dev/ Hack section, there is a thread for changing IMEI numbers elaborated, started by ameeth (a mod). I don't remember exactly where but its a stickey.
Best of luck