AP4 WIFI doesnt start

[chijika]

Advanced X7500 problem

plz.. help me.. my smartphon Not started...I tried everything but ROM- No Entry




Cmd>task 32
task 32
Level = 0

Cmd>lnbs mymac.bin 75108000
lnbs mymac.bin 75108000
Format by TrueFFS ver.: 7.1.0

:F=mymac.bin
:A=75108000
:O=00000000
:L=FFFFFFFF


start NB image download

SH
Load ADDR: 75108000 Length: 13


Programming DOC flash blocks by serial port...

Buffer=4M,0x400000
DOCInfoTableinitHW+
Binary0 Size: 0x200000
FAT0 Size: 0x5000000
FAT1 Size: 0xB00000
FAT2 Size: 0x9080000
All Size: 0xED80000
FAT0_ADDR=0x200000,FAT1_ADDR=0x5200000,FAT2_ADDR=0x5D00000
ERROR: NO header matched


Transfer CERT error

Flash Programing Error

Please help me .... I do not know English well sorry

 

[Arnold_2987]

hi
please help me , i am from iran & not writin enlish very good

my x7500 model id change to Athe400

please help me !

 

[markforbes]

Hi All, can someone tell me what is the problem if I get a LEVEL=FF onstead of 0 when typing in Task 32?

Your assistance will be appreciated.

 

[lakeman]

think this means your phone hasn,t been unlocked

 

[schnieder]

my instructions deal with that too, but here they are again:
1) press OK when mtty pops up that small popup, instead of exiting it.
2) make sure the bin is in the same folder as mtty, and that you did not mistype the name of the bin
3) do not copypaste the command, type it in manually

maybe try copying mtty into C:\ root, along with the bin file

and who is "almost everyone"?


p.s.: you don't need XP compatibility mode, this mtty was designed for vista too

stuck in bootloader.
I have a HTC Athena x7500.

Wend I turn on the device, it goes directly to bootloader and
the screen is:

ATHE 100
IPL - v1.00
ATHE 100
SPL-v3.05.0000 OR my old spl is 1.10
I have tried to change the language of my athena and then he died :spanish > fransh
USB (wend is to connect)
series (wend is unconnectable).

I can not turn the unit off by pressing the button, but must take
the battery.

I have tried with hardspl its not working
I want a solution in the forum xda-develop it says my q must upgrade to the rom of espana oficial
After downloading the rom:Advantage_HTC_SPA_2.21.412.1_1.50.00.00_Ship
I tried to upgrade to this rom May j has a mesage on my athena screen:

found spl v1.10
dowload Spl before v3.05 is not allowed!

I tried to update it with the sd card i have the same mesage

upgrade with athenaUnlucker not work
upgrade with hardspl v7 not work
upgrade with CheetahUnlocker not work
upgrade with athena wraper not work

I have explored ruu_signeg.nbh with notepad jai entered the signer spl 1.10 I know if c is sure or not
I believe there is a problem in the image rom saved in my athena rom
what I see on the screen of my athena is the spl 3.05.0000
The real spl is 1.10there is confusion in my spl
is what I can fix this problem with mtty
so if possible please guide me
I board on my pda (cid locked)on the Spanish language HTC_304
sorry for my bad Englis
thank you in advance
My email: [email protected]

 

[juanbazzi]

Cmd>lnbs mac3.bin 75108000
lnbs mac3.bin 75108000

Cmd>task 32
task 32
Level = 0

Cmd>lnbs mac3.bin 75108000
lnbs mac3.bin 75108000
Format by TrueFFS ver.: 7.1.0

:F=mac3.bin
:A=75108000
:O=00000000
:L=FFFFFFFF


start NB image download

SH
Load ADDR: 75108000 Length: 800


Programming DOC flash blocks by serial port...

Buffer=4M,0x400000
DOCInfoTableinitHW+
Binary0 Size: 0x200000
FAT0 Size: 0x5000000
FAT1 Size: 0xA00000
FAT2 Size: 0x9080000
All Size: 0xEC80000
FAT0_ADDR=0x200000,FAT1_ADDR=0x5200000,FAT2_ADDR=0x5C00000
ERROR: NO header matched


Transfer CERT error

Flash Programing Error

 

[bendeer]

Is there possibility to get Level=0 when device stuck on bootloader? ( wrong spl loaded .. )

or is there any option to change CID? My actually CID is HTC_F08 - Denmark.. I'm looking for a correct rom for something like a 3 days.. with no effect.

 

[B-44]

The matter aint no wrong SPL- it's the question what you do with/to the one you have...

 

[raosp]

error message

Hi, well i tryed to do everything like in the post but after i wrote the comand " Lbns filename.bin 75108000" it gives me "command error" i named the bin file mac, i think its ok right ?
so how can i do it right ?
thanks in advance.

here's an experimental program I made to make the process more automatic so users can fix their own wifi without our help.


this is good for both corrupt modelid and corrupt wifi, and fixes both at the same time.

STEP BY STEP:

1. download attachment at the end of the post for mac1.exe (requires .net 2.0 installed on the PC)
2. you will also need to download the other attachment in this post for the mtty program.
3. enter bootloader (tricolour screen) manually by pressing and holding camera button all the way in (yes I mean that, press it in as hard as you can!!), while doing a reset, then keep the camera button held until you see the tricolour screen.
4. disable USB in activesync (wmdc if you have vista - in this case, do not kill wmdc, just disable usb in it!!!)
5. run mtty and select USB option from the dropdown box!
6. then press enter in main window that comes up, see if that gives you Cmd>
7. now you should have Cmd>, if not, re-check if you did the above steps right until you get Cmd>
8. now run the mac1.exe, type in your MAC address you want to use for the Athena, if you have SPL 3.xx reported on the tricolour screen, then use the button for SPL 3.xx, otherwise if you have SPL 1.xx reported, use button for 1.xx.
9. this should have generated a .bin file for you, copy that bin file in the folder of mtty.
10. now, in mtty, type (do not copypaste!) this command: task 32
11. this should return Level = 0
12. now, you must only do one of the two following commands:
- if you have SPL 3.xx, then type (do not copypaste!!) this command: lnb filename.bin 76508000
(there filename is the name of the .bin file you generated - don't forget to put .bin after filename, as the full name is needed).
- OR, if you have SPL 1.xx, then the command is different (do not copypaste!!): lnbs filename.bin 75108000
(there filename is the name of the .bin file you generated - don't forget to put .bin after filename, as the full name is needed).

NOTE, the command starts with a lowercase "L", not "I"!

WARNING: PLEASE DO NOT MIX UP THESE TWO DIFFERENT COMMANDS!!!
if this info helps: most people will have SPL 3.xx, and if you have AP4 (not vanilla) already running then you're definitely 3.xx

13. mtty will popup a window asking "OK", you press OK!
if you get "Fail to synchronize with the host (1)", then make sure you did follow step by step. if still same error, try placing mtty and the bin file under C:\.
14. now the file downloads, if mtty reports it flashed the file, and at the end "code entrypoint unknown", then that's it, now boot back to WM and see if wifi works.

edit: see raskell's mtty tutorial too, #36. post in this thread


if you *really* can't manage to get it working, you can still feel free to PM me.

let me know if this program and step by step description helped any.

 

[raosp]

need help

Hi, well i tried to do all this steps but in the end a error message comes up
i did : Lnb mac.bin 75108000 and it gives me "error command" what am i doing wrong ?
i placed the mtty folder in the sistem32 folder, but still no results, can you help me ?

here's an experimental program I made to make the process more automatic so users can fix their own wifi without our help.


this is good for both corrupt modelid and corrupt wifi, and fixes both at the same time.

STEP BY STEP:

1. download attachment at the end of the post for mac1.exe (requires .net 2.0 installed on the PC)
2. you will also need to download the other attachment in this post for the mtty program.
3. enter bootloader (tricolour screen) manually by pressing and holding camera button all the way in (yes I mean that, press it in as hard as you can!!), while doing a reset, then keep the camera button held until you see the tricolour screen.
4. disable USB in activesync (wmdc if you have vista - in this case, do not kill wmdc, just disable usb in it!!!)
5. run mtty and select USB option from the dropdown box!
6. then press enter in main window that comes up, see if that gives you Cmd>
7. now you should have Cmd>, if not, re-check if you did the above steps right until you get Cmd>
8. now run the mac1.exe, type in your MAC address you want to use for the Athena, if you have SPL 3.xx reported on the tricolour screen, then use the button for SPL 3.xx, otherwise if you have SPL 1.xx reported, use button for 1.xx.
9. this should have generated a .bin file for you, copy that bin file in the folder of mtty.
10. now, in mtty, type (do not copypaste!) this command: task 32
11. this should return Level = 0
12. now, you must only do one of the two following commands:
- if you have SPL 3.xx, then type (do not copypaste!!) this command: lnb filename.bin 76508000
(there filename is the name of the .bin file you generated - don't forget to put .bin after filename, as the full name is needed).
- OR, if you have SPL 1.xx, then the command is different (do not copypaste!!): lnbs filename.bin 75108000
(there filename is the name of the .bin file you generated - don't forget to put .bin after filename, as the full name is needed).

NOTE, the command starts with a lowercase "L", not "I"!

WARNING: PLEASE DO NOT MIX UP THESE TWO DIFFERENT COMMANDS!!!
if this info helps: most people will have SPL 3.xx, and if you have AP4 (not vanilla) already running then you're definitely 3.xx

13. mtty will popup a window asking "OK", you press OK!
if you get "Fail to synchronize with the host (1)", then make sure you did follow step by step. if still same error, try placing mtty and the bin file under C:\.
14. now the file downloads, if mtty reports it flashed the file, and at the end "code entrypoint unknown", then that's it, now boot back to WM and see if wifi works.

edit: see raskell's mtty tutorial too, #36. post in this thread


if you *really* can't manage to get it working, you can still feel free to PM me.

let me know if this program and step by step description helped any.

 

[B-44]

You obviously mixed the two commands and took a large L instead of lowercase one:
Lnb mac.bin 75108000

quote:
"- if you have SPL 3.xx, then type (do not copypaste!!) this command: lnb filename.bin 76508000
(there filename is the name of the .bin file you generated - don't forget to put .bin after filename, as the full name is needed).
- OR, if you have SPL 1.xx, then the command is different (do not copypaste!!): lnbs filename.bin 75108000
(there filename is the name of the .bin file you generated - don't forget to put .bin after filename, as the full name is needed).

NOTE, the command starts with a lowercase "L", not "I"!

WARNING: PLEASE DO NOT MIX UP THESE TWO DIFFERENT COMMANDS!!!"

btw: Is the name of your file "mac" ?

 

[guzh]

task 32
Level = 0

Cmd>lnbs mac2.bin 76108000
Format by TrueFFS ver.: 7.1.0

:F=mac2.bin
:A=76108000
=00000000
:L=FFFFFFFF


start NB image download

SH
Load ADDR: 76108000 Length: 929


Programming DOC flash blocks by serial port...

Buffer=4M,0x400000
DOCInfoTableinitHW+
Binary0 Size: 0x200000
FAT0 Size: 0x5000000
FAT1 Size: 0xA00000
FAT2 Size: 0x9080000
All Size: 0xEC80000
FAT0_ADDR=0x200000,FAT1_ADDR=0x5200000,FAT2_ADDR=0x5C00000
*

Done

Code entry point unknown

And still I get Device ID error when I'm trying to flash siped ROM.
SPL 1.2
MAC - valid

Please help!

 

[B-44]

task 32
Level = 0

Cmd>lnbs mac2.bin 76108000
Format by TrueFFS ver.: 7.1.0

Should be 75108000

 

[Masutin]

Anybody still around? What does this mean?
start NB image download
Load ADDR: 75108000 Length: 929
Invalid Address 0x75108000
Error! The image must be in ROM area.

 

[OUYANGDIANDIAN]

THANKS.SO