Bumper that works with mods?

[Stanleywinthrop]

Has anyone found one?

 

[Darth]

Just got a Z3 play. Had a Z, and my wife has a Z2 play. No trouble getting a bumper for those phones, but can't find one for the Z3 play. It's bumming me out, cause I have troubles with extra screen touches from my hand without the bumper. But definitely need to use mods with it, so other cases are out.

Hopefully someone makes one soon. :fingers-crossed:

 

[fdwboy]

I'd watch Sprint and US Cellular's sites once the Z3 Play is available from them. Verizon made the best bumper for the Z and Z2 series, but since they aren't carrying the Z3 Play they won't make one. Hopefully either Sprint or USC will make a bumper. Otherwise I wouldn't hold my breath since there were very few aftermarket bumpers for the Z or Z2 Play.

 

[jayb222]

In also looking for a bumper case for this phone. I hope they make one for us like the z play and play 2.

 

[Darth]

I wonder if those bumpers with the clear back, would work with the back neatly cut out. Might risk 7 bucks to try it.

 

[Stanleywinthrop]

I wonder if those bumpers with the clear back, would work with the back neatly cut out. Might risk 7 bucks to try it.

Please report back if you give it a try!

 

[Darth]

Please report back if you give it a try!

Just ordered this, and going to conduct surgery to remove the back. Wish me luck!

https://www.amazon.com/Rnicy-Shockp...i+z3+rnicy&dpPl=1&dpID=31TWxWrO-jL&ref=plSrch

 

[dieterhaack]

@Darth
I wish you good luck, indeed.
My opinion is that *any* bumper or cover will make it hard to reach the sidemounted fingerprint. it sits deeper. With Sony devices, I only used snap-on hard cover with a cutout for the sensor. Which is obviously not possible for the Z1-3 series.

Another issue forced me to dump my expensive Z2 Play Verizon Bumper: It makes the phone too large, so that I can't hold it securely with my short fingers. Two-handed usage, even without...
My solution was to use a full screen protector to prevent scatches while pulling phone out of pocket or screen facing the table. The back side has it's Mod on. This is surely no drop protection onto the edge, but this is a risk I have to live with.

 

[Darth]

@Darth
I wish you good luck, indeed.
My opinion is that *any* bumper or cover will make it hard to reach the sidemounted fingerprint. it sits deeper. With Sony devices, I only used snap-on hard cover with a cutout for the sensor. Which is obviously not possible for the Z1-3 series.

Another issue forced me to dump my expensive Z2 Play Verizon Bumper: It makes the phone too large, so that I can't hold it securely with my short fingers. Two-handed usage, even without...
My solution was to use a full screen protector to prevent scatches while pulling phone out of pocket or screen facing the table. The back side has it's Mod on. This is surely no drop protection onto the edge, but this is a risk I have to live with.

Dang, think I just wasted some cash. LoL

Didn't even think about the fingerprint sensor, which I really don't want to lose. Ah well, I'll have a lightweight case that still lets the nice looking back be seen, that I can use when I don't need the battery mod. Which I don't think I need much really, the battery life has been awesome for me.

My Z had a fried battery I'm sure, would barely last an hour and a half of use. So the battery mod was a full time necessity. Not the Z3 play though. Doubt I need it except as emergency power when I'm not near a plug, or for sitting on the couch.

 

[Darth]

So I got the case delivered that I linked above. And got to cutting the rubber sides off of the harder clear back.

The bumper does have a cut out for fingerprint scanner and works fine. So that's good! I rushed and my cutting job is really not nice. That's on me. A sharper utility knife blade and taking my time more would have made for a much neater cut. Did it on a breadboard and was extremely careful not to slip and cut a corner open. Really took time cutting out the corners.

I basically cut right along the edge of the hard clear back plastic. My knife was kinda dull though. Was too impatient to get a new blade for it.

But, success! It's on, stays on, and my battery mod is on. It's way flimsier than my Z's old bumper or my wife's Z2 play bumper, but those were thicker cause they were made without backs and made thicker. So the sides move a bit and are a wee bit floppy, but the corners are tight, so it stays on.

Aside from the back being a bit ugly cause of my bad cut, which I'll try to tidy up later, it does work. Just a but flimsy. But I still prefer it to no bumper, for me personally.

I'll probably only use it at home, and will definitely buy a real one if someone ever makes one. I'd like a thicker more sturdy one for sure.

**Try at your own risk and satisfaction not guaranteed.** :laugh:

 

[Stanleywinthrop]

So I got the case delivered that I linked above. And got to cutting the rubber sides off of the harder clear back.

The bumper does have a cut out for fingerprint scanner and works fine. So that's good! I rushed and my cutting job is really not nice. That's on me. A sharper utility knife blade and taking my time more would have made for a much neater cut. Did it on a breadboard and was extremely careful not to slip and cut a corner open. Really took time cutting out the corners.

I basically cut right along the edge of the hard clear back plastic. My knife was kinda dull though. Was too impatient to get a new blade for it.

But, success! It's on, stays on, and my battery mod is on. It's way flimsier than my Z's old bumper or my wife's Z2 play bumper, but those were thicker cause they were made without backs and made thicker. So the sides move a bit and are a wee bit floppy, but the corners are tight, so it stays on.

Aside from the back being a bit ugly cause of my bad cut, which I'll try to tidy up later, it does work. Just a but flimsy. But I still prefer it to no bumper, for me personally.

I'll probably only use it at home, and will definitely buy a real one if someone ever makes one. I'd like a thicker more sturdy one for sure.

**Try at your own risk and satisfaction not guaranteed.** :laugh:

Thanks Darth! Can you keep us updated about how it holds up?

 

[jayb222]

You'd think someone wouldn't made an official one by now. It uses less plastic to make a bumper.

 

[jayb222]

Finally found one on sale on amazon! If anyone gets it, please give impressions.
It's aluminium so Idon't know how it will work with the fingerprint sensor. Reviews say it's a bit too thick to place your finger correctly. Now that verizon is supplying the Moto Z3 they might release a rubber bumper like the ones for the moto Z and Z2. I'll wait and see.

Moto Z3 Play Case,Dngn Luxury [Aluminum Alloy Frame Bumper


https://www.amazon.com/Dngn-Luxury-Aluminum-Shockproof-Motorola/dp/B07FYBRSKH/ref=sr_1_15?ie=UTF8&qid=1533592842&sr=8-15&keywords=moto+z3+bumper

This looks to be more of the same by another dealer but the pics show no figerprint sensor. Reviews do say there is one though.:
https://www.amazon.com/HikerClub-Aluminum-Pattern-Silicone-Motorola/dp/B07F6C3HHX/ref=sr_1_7?ie=UTF8&qid=1533594325&sr=8-7&keywords=moto+z3+bumper#customerReviews

 

[pizza_pablo]

Finally found one on sale on amazon! If anyone gets it, please give impressions.
It's aluminium so Idon't know how it will work with the fingerprint sensor. Reviews say it's a bit too thick to place your finger correctly. Now that verizon is supplying the Moto Z3 they might release a rubber bumper like the ones for the moto Z and Z2. I'll wait and see.

Moto Z3 Play Case,Dngn Luxury [Aluminum Alloy Frame Bumper


https://www.amazon.com/Dngn-Luxury-Aluminum-Shockproof-Motorola/dp/B07FYBRSKH/ref=sr_1_15?ie=UTF8&qid=1533592842&sr=8-15&keywords=moto+z3+bumper

This looks to be more of the same by another dealer but the pics show no figerprint sensor. Reviews do say there is one though.:
https://www.amazon.com/HikerClub-Aluminum-Pattern-Silicone-Motorola/dp/B07F6C3HHX/ref=sr_1_7?ie=UTF8&qid=1533594325&sr=8-7&keywords=moto+z3+bumper#customerReviews

I have one like this, from eBay, for the Z2 Play. The "bumper" does not stay on the phone, without the back of the case attached. Even with a Mod attached to the phone it does not seem like the "bumper" portion will remain on the phone. It is very loose.

 

[Darth]

I have one like this, from eBay, for the Z2 Play. The "bumper" does not stay on the phone, without the back of the case attached. Even with a Mod attached to the phone it does not seem like the "bumper" portion will remain on the phone. It is very loose.

I saw a review saying the same. Disappointed.

 

[jayb222]

I saw a review saying the same. Disappointed.

I have one like this, from eBay, for the Z2 Play. The "bumper" does not stay on the phone, without the back of the case attached. Even with a Mod attached to the phone it does not seem like the "bumper" portion will remain on the phone. It is very loose.

Well that is disappointing. Oh well, I'm waiting on you Verizon. Provide us with that little piece of plastic. Anyone for that matter!

 

[kenbrownstone]

Also this case I have for my z2force and it interferes with reception of the antennas. Had it on for ten minutes then just threw it into the trash. I had a company I reached out to and said they were making some.I bought one of theirs for the force 2 and it was hands down best bumper I had..

Sent from my Moto Z3 Play using Tapatalk

 

[pizza_pablo]

Also this case I have for my z2force and it interferes with reception of the antennas. Had it on for ten minutes then just threw it into the trash. I had a company I reached out to and said they were making some.I bought one of theirs for the force 2 and it was hands down best bumper I had..

Name of company?

 

[kenbrownstone]

Name of company?

The same one u we're talking about.. Also got it in the Moto z play version and it was worse on reception and wouldn't stay on ,was to big..If they would've been better I would buy for my z3

Sent from my Moto Z3 Play using Tapatalk

 

[kenbrownstone]

Name of company?

Just got this

Sent from my Moto Z3 Play using Tapatalk