Defy's Flashlight has dead.

[lackyking]

Has already been fixed by replacing the LED problem.
http://www.itfunz.com/thread-84762-1-1.html

 

[shady_lanem]

Can someone translate that to english please!

 

[reinsen]

First, remove the battery, SIM card and memory card, mobile phone with a T5 screwdriver to screw the sides and top of the 9 removed the back cover the phone apart.


Second, the flash is the hot melt in the back cover, so use the blade to slowly cut off the three gel-point, and then remove the flash PCB assembly (be careful not to cut around to the back cover or may not waterproof)


Third, the LED cover cut with a blade down, and then blowing hot air gun under the LED chip. High temperature adhesive tape with a small piece of the pad will be posted up by the cathode, the other three after the solder paste coated pads will creeLED paste pad, over reflow furnace. ,



Four, painted around 705 in the LED plastic lens and then processed (grinding thin, hole expansion), cast clinched LED. .



Fifth, in half an hour after the glue dried LED flash Replace the back cover, the location of the three columns marked with 705 plastic glue. ,



VI Adhesive will cover installed, remove the nine screws lock, replacement LED success,,,


Note: There are three joints in the PCB are linked, a separate LED that is positive, next to the pad to use separate high temperature adhesive tape. Sure to remove the LED in the square before the EVA blowing hot air heat gun to take down.


Cree LED is used by R2, XP-E Series color temperature 4300-5000K, outdoor white. The maximum LED current up to 1000mA,
Open with a camera flash, the current is only 35mA, very bright, should not be burned out.
I was in the general environment for, and the screen and the motherboard up with plastic bags just fine. Not into the ash.

is it so hard to use google?

 

[psicodelico]

My flash is not burn. I can turn it on and off using a app for that but when i go take the picture the flash color is blue/green.

 

[jeffokada81]

Can someone translate that to english please!

Use Google chrome, it will ask you to translate or do it automatically for you.

 

[Darkcaptain]

Someone who does not work the Flash, has tested the new ROM China?

I want to try, but do not know if it works with the MB525 and the current ROM I have (Froyo Orange PL)

 

[chaihg]

Since it is not even a year since this phone released, why dont all of you who have a burnt LED give back your device and claim it under warranty?.
You would get a new device right. Its easy to restore whatever rom you came from.

 

[Zaben]

I was going through build.prop for some thing else and noticed these settings on my 3.4.2-145 build.

ro.media.capture.flashIntensity=41
ro.media.capture.torchIntensity=25

What are these set to for the Chinese ROM?

 

[Jt612]

So there is no solution for the green/weak flash light problem?

 

[Darkcaptain]

So there is no solution for the green/weak flash light problem?

I not think , my phone has been sent to the Motorola Technical Service by the famous problem of the speaker (in calls) and also by the flash camera.

In 15 days say it will be repaired, I will write here.

Sorry for my english.

 

[Jt612]

will it damage my phoen further trying the lightfix? to see if it fixes the gren flash problem?

 

[dogo2]

Yesterday I looked my LED under a microscope and unfortunately there were some brown spots on it. I compared it to a working LED and as you may think it hadn't any brown spots... So I guess it is really burnt

I installed the original firmware and sent it back to be repaired. I'm waiting only for an official update now

 

[edition-]

will it damage my phoen further trying the lightfix? to see if it fixes the gren flash problem?

Us that are on "undowngradable" ROM's i guess we will have to wait for an official 2.2 and then send to repair :\

 

[dogo2]

I'm not sure why everybody speaks of undowngreadable... I have installed this ROM and then flashed back the original 2.21.0 (DE, AT, CH) - MotoBlur sbf from here with RSDLite. Everything went ok.

I have to say I'm not an expert. I cannot promise this will work on your phone too.

 

[shady_lanem]

Bummer My flashlight is near to useless. Can't even lights up an inch away. Well, I'm getting Atrix in few days then sending this back to warranty

 

[slashvanyoung]

My LED flash died as well and yes, I did mess with the earlier Chinese Froyo ROMs so that might have caused the issue.

Before the flash completely died, I noticed it going out of sync with the camera.

Fortunately, I didn't have to wait for weeks to get my repaired Defy back. They got me a replacement within a day.

 

[edition-]

I'm not sure why everybody speaks of undowngreadable... I have installed this ROM and then flashed back the original 2.21.0 (DE, AT, CH) - MotoBlur sbf from here with RSDLite. Everything went ok.

I have to say I'm not an expert. I cannot promise this will work on your phone too.

Jboogie's ROMs are all downgradable , i got passed 2.51 and all the froyo builds, can't get back :\

 

[fabianowerner]

My flashlight was OK on Pays Rom 4.1 but i figured that it was weak, reflashed original Eclair 2.1 and now its very weak, barely can see it on video camera, and the photo camera it flashes but only a weak light that cant light up nothing. And when i tried to turn it on using an app (Flashlighter) it went very very weak and only a small brown point turned on. Did i break my flashlight?

 

[naenee]

The LED light was not designed to be used as anything other than a camera flash. Using it as a flashlight may well have broken it.

Hm. That said, the video recording feature has a button to toggle the LED, which would contradict my above statement

 

[fabianowerner]

my led now is gone, cant turn it on using videocamera, and its really weak with green light at the end, using photo camera.