[DFT][Updated!#3] HSPL / RSPL for HTC WP7 First Generation

Search This thread

kaijai87

New member
Mar 28, 2009
3
0
Link to DFT HSPL/RSPL R#3

I have an HTC Arrive and I'm trying to run RSPL/HSPL so I can load a custom rom onto my phone. Anybody have a link to the DFT HSPL/RSPL R#3 program or have a copy that they can upload? The link in the thread is broken and I can't find it anywhere online. I've searched high and low. Anyone that can help me with this? I can offer a small donation via PayPal for your troubles.
 

dxdy

Senior Member
Apr 17, 2008
5,051
2,109
49
www.red-gsm.net
Nokia Lumia 920
Xiaomi Mi Mix 2S
I have an HTC Arrive and I'm trying to run RSPL/HSPL so I can load a custom rom onto my phone. Anybody have a link to the DFT HSPL/RSPL R#3 program or have a copy that they can upload? The link in the thread is broken and I can't find it anywhere online. I've searched high and low. Anyone that can help me with this? I can offer a small donation via PayPal for your troubles.

did you check SPL version in bootloader?

here is link
https://mega.co.nz/#!VopnmCAT!CflMfC_L3k8nuKUex8DOiUKSAnNLPbC4Q0dsToiZGPI

if device not restart to RSPL, you must flash this
http://rapidshare.com/files/1996657....00.01_23.12W.05.06U_NoDo_Signed_by_ansar.zip

and no need for donation... this links is already on forum...
 

kaijai87

New member
Mar 28, 2009
3
0
Thanks!

Thanks so much for the link. I really appreciate it. My SPL version was 3.xxx (can't remember exactly); whatever comes with Mango. I flashed NoDo to downgrade it to 1.25, so I am ready to use the DFT tool and RSPL then HSPL. Thanks again!
 

dxdy

Senior Member
Apr 17, 2008
5,051
2,109
49
www.red-gsm.net
Nokia Lumia 920
Xiaomi Mi Mix 2S
I choose Exact my spl version, and for the software it runs correctly telling me phone suppoesd to be restarted to rspl but my phone doesn't do that . it stays at spl screen

first check did MID's (Model ID - first line in bootloader screen) supported by HSPL, in first post you have list of supported MIDs

make hard reset to have clean ROM on phone

when you install HSPL, if not restart, try repeat process again from beginning (turn off phone, boot to bootloader...)... sometimes work after few trying... or choose different SPL on list, is not matter if not same as on phone...

also you can try flash stock NoDo ROM for your device to change SPL on phone.. if you tell which phone have, i can give you link for recommended stock NoDO ROM to flash it with SPL which work to change it to HSPL...
 

Krokotam_

Member
Nov 5, 2007
11
0
So i have done everything but i have constant error that Vendor ID is different . My phone is from TMOUS i want to flash Europian rom to it . My SPL ver is 1.202250.0 .
 

jfostr

Member
Dec 10, 2010
35
0

dxdy

Senior Member
Apr 17, 2008
5,051
2,109
49
www.red-gsm.net
Nokia Lumia 920
Xiaomi Mi Mix 2S
The link for the newest version of the HSPL doesn't seem to be working for me. Is there another way you could post it?

both links is OK...
but here other
http://www20.zippyshare.com/v/48515887/file.html

---------- Post added at 08:10 AM ---------- Previous post was at 08:09 AM ----------

So i have done everything but i have constant error that Vendor ID is different . My phone is from TMOUS i want to flash Europian rom to it . My SPL ver is 1.202250.0 .

you need Y-USB cable and gold card method....
 

bleros

Senior Member
Mar 17, 2012
612
232
system32
Pleasee somebody help me i cant downgrade with any tutorial here spl driver are installed the usb not show on white screen i have installed wmdc but not work how to downgrade spl please
 

Attachments

  • 20140111_021228.jpg
    20140111_021228.jpg
    255.2 KB · Views: 183

eeeeeeehsan

Member
Jan 18, 2010
10
1
Hi guys
I have no Idea what i did but my modelID has changed to a strange letters that don't allow me to flash rom or rspl. i try tu oslp but the error:

Code:
[Error Description]:

OSPL detected. Please run RSPL launcher first!

[Info]: USBWorkHSPL.cpp (286)

I try the rspl and the errors:

Code:
[Error Description]:

Invalid ModelID. This means that your phone not supported.
This installer supports only limited number of the phones.
SPARK, MOZART, MONDRIAN, GOLD, SCHUBERT.
If you have phone from this list, but still have this error, please contact with DFT team.

[Info]: USBWorkRSPL.cpp (235)


[Error Description]:

ModelID is 'yðöâ3(å'. Please report this info to DFT.

Doas somebody knows the answer?!
 

eeeeeeehsan

Member
Jan 18, 2010
10
1
Hi guys
I have no Idea what i did but my modelID has changed to a strange letters that don't allow me to flash rom or rspl. i try tu oslp but the error:

Code:
[Error Description]:

OSPL detected. Please run RSPL launcher first!

[Info]: USBWorkHSPL.cpp (286)

I try the rspl and the errors:

Code:
[Error Description]:

Invalid ModelID. This means that your phone not supported.
This installer supports only limited number of the phones.
SPARK, MOZART, MONDRIAN, GOLD, SCHUBERT.
If you have phone from this list, but still have this error, please contact with DFT team.

[Info]: USBWorkRSPL.cpp (235)


[Error Description]:

ModelID is 'yðöâ3(å'. Please report this info to DFT.

Doas somebody knows the answer?!
 

indigold

Senior Member
Aug 11, 2011
421
40
warri
A friend of mine gave me an hd7 so I try install xspl (rspl /hspl) device is supported from op instructions. Spl version is 1.60, but when I run rspl it tells me congratulations but phone doesn't boot to rspl, it remains on spl, and when I try changing spl by flashing a stock 3.xx rom, it doesn't go pass 0%. But phone can boot on fine. What do I do?
 

Top Liked Posts

  • There are no posts matching your filters.
  • 175
    DFT HSPL RSPL WP7F3

    DarkForcesTeam proudly presents RSPL / HSPL
    for phones HTC WP7 First Generation



    (Short name is “WP7F”)
    This is first big step to customization and community development for these devices.


    History:


    15.02.2012 Updated release. Revision #3.
    Changes:
    • Was added support for 'SCHU1000' and 'PD291200' MIDs
    • Removed OTA update inside RSPL and HSPL, this allows to keep HSPL after HTC OTA Zune update.
    • Added warning screen about 4.XX and 5.XX
    • But still NO support for 4.XX and 5.XX
    • Support for CDMA devices: GoldC and SparkW
    • Wizard UI: only WWE support remains.

    NOTE for ROM chefs:
    SparkW custom ROMs must has "SPAW1000" MID instead of "PC402000".
    This is done to protect from flashing Spark custom ROM to Spark_W and reversed.



    18.08.2011 Updated release. Revision #2.
    Changes:
    • Improved wizard GUI on non DPI 96 systems.
    • Added support for "PD291300", "PD291500" two new Schubert MIDs.
    • Replaced RSPL and HSPL for Spark from 1.10 to 1.20.
    01.08.2011 Initial release. Revision #1.




    WARNING TO ALL:
    Do NOT use RSPL / HSPL with Mozart 4.XX and other RUU ROMS with MANGO.
    All WP7F devices affected: MOZART, GOLD, SCHUBERT, MONDRIAN, SPARK!
    It will damage your device. Not a joke.
    MORE INFORMATION HERE



    Read the next few messages for more information.


    This release supports those WP7F devices:

    *Gold (HTC Pro 7,T7575)
    *Mozart (HD3,T8697,T8698,T8699)
    *Mondrian (Surround,T8788)
    *Spark (Trophy,T8686)
    *Schubert (HD7, HD7S, T9292,T9295,T9296)
    *HTC Gold C (HTC Arrive)
    *HTC Spark W (Trophy Verizion)


    Most of these devices have several MIDs (ModelID, looks like “PC921000”).
    Current release supports only some limited number of MIDs. This was designed to minimize possible harm to user’s devices.

    List of supported MIDs:

    Gold: “PC92****”, “PC921000”
    Mozart: “MOZA1000”, “PD67****”, “PD671000”, “PD671200”
    Mondrian: “PD26****”, “PD261000”, “PD261100”
    Spark: “PC401000”
    Schubert: “PD29****”, “PD291000”, “PD291100”, "PD291200", "PD291300", "PD291500"


    !Please note that on SPL screen MID is only 7 symbols, without last one.!

    Programs stops any operations if unknown MID detected. If your device have unknown MID, please report about it in this thread. Specify your MID, device name, ROM versions. It’s nice, if you can give a link to download ROM.


    Basic stuffs to know:

    SPL is Secondary Program Loader. It allows to flash ROMs to device.
    Without working SPL device is fully bricked, you can’t restore it. It’s why all operations with SPL are dangerous.
    OSPL is Original SPL. This SPL comes with stock ROM and doesn’t allow to flash custom stuffs.
    RSPL is Reloaded SPL. It load only to RAM, so it doesn’t persistent. It’s enough to soft reset device to get OSPL back.
    HSPL is Hard SPL. It’s permanently flashed to internal device memory and replaces OSPL. After soft reset you still have HSPL instead of OSPL.

    This release consists from RSPL and HSPL wizards.
    For regular users, who flash ROMs rather rare, it can be enough to use only RSPL.
    For advanced users and ROM makers, it can be useful to install HSPL.


    IMPORTANT NOTES
    1. Before doing any operations be sure you have battery level more than 50%!
    Sometimes in SPL mode WP7F devices DO NOT charge. You may got a cold brick if it power down during SPL or RADIO update!
    2. Stock RUU ROMs have two NBH inside, SPL_Signed and RUU_Signed.
    So it's not possible directly flash stock ROM, you need extract files and remove SPL_Signed.nbh at least.
    3. Rememeber if you have HSPL and you flashing stock RUU_Signed.nbh you lost HSPL!
    4. Supported OS: Windows XP, Windows Vista, Windows 7.


    Warranty Issues

    Be warned, using RSPL may void your warranty.
    If you need to send your device to a Repair Centre, make sure that it looks like stock! Install stock official ROM before go to Repair Centre.


    Disclaimer

    This product is free to use at your own risk. We take no responsibility for any conflict, fault, or damage caused by this procedure. No warranties implied or otherwise, are given if you agree to use this product. No problems were found while testing this product on several different devices, your experience may vary.
    Use of the Product for commercial purposes is strictly prohibited.
    It’s not allowed to make changes to this package; it must be distributed as original release.




    Last version (R#3)


    attachment.php



    Official DFT site (Chinese)


    -DFT, 18.08.2011
    56
    Launching RSPL


    DFT_RSPL_WP7FG1_LAUNCH allows you to load RSPL on the device:

    1. Extract ALL files from RAR archive.
    2. Run DFT_RSPL_WP7FG1_LAUNCH (with administrative rights to access USB)
    3. Mindfully reads information text. Press “Next” button.
    4. Reset your device and hold “Volume Down” button during reset to enter OSPL mode.
    5. Connect your device to PC via USB cable.
    6. Now you may need to install proper USB drivers. They come with Active Sync / Windows Mobile Device Center.
    7. Install drivers if required.
    8. Make sure device show “USB” at the bottom instead of “Serial”.
    9. Press “Next” button in the wizard. It should detect your phone.
    10. If you are using WCEUSBHS driver under Windows Vista/7 (for MTTY or MAGLDR TTY for example), you should apply “Windows XP compatible mode” in the properties of EXE file to get connection.
    11. After successful connection it should show device codename and allows to choose installed OSPL version.
    12. You should look at the screen and select OSPL version in drop down list box. You need do this because it’s not possible to detect installed version via USB.

    If your current SPL version doesn't present in the list, you can choose nearest version,
    BUT ONLY IF IT HAS SAME FIRST NUMBER!!
    Example: You have 4.XX on the device. Do NOT choose 1.XX 2.XX 3.XX.


    13. Press “Next”. Wait until comes final page.
    14. Read and close window
    15. Look at the device – it must reboot to RSPL.
    16. If you see RSPLX.Y.Z and “CotullaRSPL” on the screen – the task done! Otherwise, please report in this thread about your problems.
    17. Put some feedback in this thread for community and developers.


    Installing HSPL


    DFT_HSPL_WP7FG1_INSTALL allows you to install HSPL on the device:

    1. Launch RSPL on the device like described above.
    2. Be sure that you close RSPL wizard window.
    3. Run DFT_HSPL_WP7FG1_INSTALL.exe (with administrative rights to access USB)
    4. Mindfully reads information text. Press “Next” button.
    5. Proper drivers already must be installed in RSPL step.
    6. Press “Next” button in the wizard. It should detect your phone.
    7. If you are using WCEUSBHS driver under Windows Vista/7 (for MTTY or MAGLDR TTY for example), you should apply “Windows XP compatible mode” in the properties of EXE file to get connection.
    8. After successful connection it should show device codename and allows to choose HSPL or OSPL version to install. OSPL means you install stock SPL back.
    9. Check device codename, if something wrong turn off computer and run to the nearest forest. Grab some water with yourself.
    10. Press “Next”. Wait until comes final page.
    11. Device will reboot and start to boot OS.
    12. Reset it and enter SPL mode again. Be sure there HSPLX.Y.Z and “CotullaHSPL” appear.
    13. Put some feedback in this thread for community and developers.
    31
    Example of HSPL screen on HTC Schubert:

    attachment.php
    21
    @cotulla Should we be expecting a magldr release soon? ;-) I heart dual booting!
    for LEO - yes. about WP7F, we have some experiments and runnning some MAGLDR version on Gold and Mozart, but not sure how deep it will go.
    because this devices are not so lucky as LEO, some things make stuffs difficult, like external audio codec and other ril interface. Last thing can stop porting for a long time. time will show truth ;) but I can't promise anything. LEO is still The King. haha.
    19
    Issues with MANGO RUU ROMS.


    List of such ROMs:

    It's not full list. Maybe some other ROMs affected by this too.
    Thread about this ROMs.

    RUU_Gold_S_HTC_Europe_3.02.401.01_Radio_5.69.09.29 a_22.50.50.21_Signed_GOLD_RELEASE.exe
    RUU_Mozart_S_HTC_Europe_4.06.401.00_5.69.09_RELEAS E.exe
    RUU_Mozart_S_HTC_RUS_4.06.411.00_5.69.09_RELEASE.e xe
    RUU_Schubert_S_HTC_Europe_4.05.401.02_Radio_5.69.0 9.29a_22.50.50.21_Signed_SCHUBERT_RELEASE.exe
    RUU_Spark_S_HTC_Europe_4.06.401.00_5.69.09_RELEASE .exe


    About issue:

    After running RSPL on MANGO OSPL, you can't flash device via SPL.
    Windows Phone 7 OS is still booting and working.
    Instead of full SPL screen you will see only one the first line:
    You device will be "HALF BRICKED", because you can use OS, but can't flash anything else.

    attachment.php


    At the current moment it's IMPOSSIBLE to recover such devices. And I am not sure it will be ever possible.


    What you must NOT do:

    Before running RSPL wizard check your SPL screen.
    There current SPL version at top: "X.Y.Z 2250 "
    When wizard asks you to choose your current SPL version, be sure it's present inside versions list.
    If your current SPL version doesn't present in the list, you can choose nearest version, BUT ONLY IF IT HAS SAME FIRST NUMBER!!
    Example: You have 4.XX on the device. Do NOT choose 1.XX 2.XX 3.XX.

    Generally it means that you must NOT run RSPL wizard after MANGO RUU ROM installation. You must flash older version (with 7004 or NoDo) and then run RSPL.
    Installed OS version doesn't important. Only SPL version important.