[Discussion & Feedback] OxygenOS 10.3.7 OTA for OnePlus 6T

Search This thread

Pablo.x

Senior Member
Mar 6, 2014
851
319
OnePlus 6T
sure. the easiest way is as follows:
1) download 10.3.3 and place on root of sd
2) in system update, select local update, once finished DO NOT REBOOT
3) open magisk, flash twrp - DO NOT REBOOT
4) once twrp flashed, select install magisk to inactive slot
5) reboot - profit

This would work even with TWRP installed? :confused:
 
Dec 27, 2013
9
5
Went to 10.3.2 and MMS on the Google Message app completely stopped working. Have to use the stock app which I hate.

Tried installed TWRP (3.3.1-1-1-fajita.zip) and I lose wifi. Have to flash the OTA update to get wifi back.

About to try a wipe and install but hate FDR...

UPDATE: Followed @contesauce and tried the Omega kernel. Bam, Wifi is back. Haven't tried flashing Magisk yet though...

After much testing this setting worked for me after a restart! Go to the phone dialer and type *#*#4636#*#* and click Phone Information and change the Set Preferred Network to the below in the screenshot. If yours is already set to this Preferred Network change it to something else as I have changed mine to many different ones until coming back to this one which was my original setting and let the system cycle through to identify the network settings and then change it back to the below. Lastly restart your phone and test as you should be able to now receive and send multimedia messages using the Google Messenger app! Good luck
 

Attachments

  • Screenshot_20200508-063714.jpg
    Screenshot_20200508-063714.jpg
    172 KB · Views: 1,367

Koushik87

Senior Member
Nov 3, 2014
61
17
34
Kolkata
Is there some way to get rid of the OnePlus Account in the settings? It appeared after a playstore update of the OnePlus account app. Already tried to deactivate the app but it stills stays in the settings on top.

Go to the the TWRP thread by maurinfrio. You will find a zip stating Fake India partition deleter. Flash it through TWRP and that weird account info will be disabled.
 

Libraplum76

Senior Member
Oct 25, 2017
134
41
Reside where peace is present
Hello everyone,

I have a Oneplus 6T internationally unlocked phone running on OOS 10.3.3 and I am trying to
to see if a MetroPCS sim card will enable me to have volte. Has anyone confirmed or
know if a MetroPCS sim card will allow my phone to have Volte enabled?

Thank you
Any help is appreciated
 
Last edited:

clsA

Senior Member
Aug 28, 2010
9,823
3,458
Central Florida
Hello everyone,

I have a Oneplus 6T internationally unlocked phone running on OOS 10.3.3 and I am trying to
to see if a MetroPCS sim card will enable me to have volte. Has anyone confirmed or
know if a MetroPCS sim card will allow my phone to have Volte enabled?

Thank you
Any help is appreciated

Not sure about Metropcs but my AT&T sim has it enabled
so unreal mobile or Cricket would also work
 

scorpio76r

Senior Member
Jan 10, 2016
1,123
413
All over like street lights
Hello everyone,

I have a Oneplus 6T internationally unlocked phone running on OOS 10.3.3 and I am trying to
to see if a MetroPCS sim card will enable me to have volte. Has anyone confirmed or
know if a MetroPCS sim card will allow my phone to have Volte enabled?

Thank you
Any help is appreciated
Sure, here you go.
 

Attachments

  • Screenshot_20200512-172935.jpg
    Screenshot_20200512-172935.jpg
    195.4 KB · Views: 884
  • Screenshot_20200512-173046.jpg
    Screenshot_20200512-173046.jpg
    209.5 KB · Views: 880

Artnig

Senior Member
Mar 5, 2014
276
54
After much testing this setting worked for me after a restart! Go to the phone dialer and type *#*#4636#*#* and click Phone Information and change the Set Preferred Network to the below in the screenshot. If yours is already set to this Preferred Network change it to something else as I have changed mine to many different ones until coming back to this one which was my original setting and let the system cycle through to identify the network settings and then change it back to the below. Lastly restart your phone and test as you should be able to now receive and send multimedia messages using the Google Messenger app! Good luck

Did not work for me. Anyone else unable to get MMS on Verizon after 10.3.3 update?
 

hondoslack

Senior Member
Apr 6, 2009
194
37
sure. the easiest way is as follows:
1) download 10.3.3 and place on root of sd
2) in system update, select local update, once finished DO NOT REBOOT
3) open magisk, flash twrp - DO NOT REBOOT
4) once twrp flashed, select install magisk to inactive slot
5) reboot - profit

Apologies for the dumb question, but I do not see a "flash twrp" option in Magisk (step 3)?
Also, for step 4, where is this option? Magisk home page INSTALL button does not give the option to install to inactive slot?
Are these steps performed using specific Magisk modules?

Thanks
 

thirtythr33

Senior Member
Sep 3, 2011
215
99
New York
OnePlus 6T
OnePlus 9 Pro
Apologies for the dumb question, but I do not see a "flash twrp" option in Magisk (step 3)?
Also, for step 4, where is this option? Magisk home page INSTALL button does not give the option to install to inactive slot?
Are these steps performed using specific Magisk modules?

Thanks

no worries, but no, not any magisk modules per se, you will be grabbing the latest twrp.zip and flashing that, and then install - install - install to inactive slot in magisk manager
 

hondoslack

Senior Member
Apr 6, 2009
194
37
no worries, but no, not any magisk modules per se, you will be grabbing the latest twrp.zip and flashing that, and then install - install - install to inactive slot in magisk manager

Is the attached what you are referring to? Magisk Manager does not contain an option to flash anything, which is why I'm wondering. Not sure how I can flash anything without rebooting to TWRP?
 

Attachments

  • Screenshot_20200516-150654.jpg
    Screenshot_20200516-150654.jpg
    154.8 KB · Views: 578

alryder

Senior Member
Apr 15, 2012
496
204
Lansing, MI
Is the attached what you are referring to? Magisk Manager does not contain an option to flash anything, which is why I'm wondering. Not sure how I can flash anything without rebooting to TWRP?

Download the TWRP installer file (TWRP 3.3.1-32 Unofficial Installer by mauronofrio) and save it on your phone. In Magisk Manager go to Modules and click the + at the bottom of the page. Browse to where you saved the TWRP installerfile and install (Flash) it. DON'T REBOOT.

Click Install next to Magisk, click Install again and click Install to Inactive Slot (After OTA). After installation is done, press the reboot button in Magisk Manager.
 

Riddle5

Senior Member
Nov 27, 2013
374
48
Zamora
Hey! I need your help, update the FaceUnlock app and now I can't use that function, does anyone know how to reverse that? I already tried installing the previous version but I don't know how to install
 

onliner

Senior Member
Oct 29, 2016
2,420
1,027
Hey! I need your help, update the FaceUnlock app and now I can't use that function, does anyone know how to reverse that? I already tried installing the previous version but I don't know how to install

Settings/apps/show all apps/show system apps/face unlock/uninstall updates.
 
  • Like
Reactions: pbergonzi

Top Liked Posts

  • There are no posts matching your filters.
  • 12
    Stable 10.3.11 is up - Link

    Mirror to AFH - AFH

    md5 - 58b702514110187ba4dadc91f5dd9e30

    Stock boot image - Stock

    Magisk patched image - Patched

    Changelog
    System:
    • Updated Android security patch to 2021.05
    • Fixed known issues and improved system stability
    3
    That's awesome! Thanks for the link to the iFixit for the battery!! Was looking for a place where I could trust the reviews...

    Just curious if you got the adhesive seal in the package you ordered? If not how did you reseal the back cover on?

    Also, what do you mean by "getting 10+ hours again with Advanced charge controller stopping charge at 75%" ?

    Are you referring to AccuBattery App?

    Looking forward to your reply.

    ✌️
    I GOTCHU FAM!

    It only has the battery, my thoughts were "I always keep my phone in a case, so if I can salvage a little adhesive to just hold the phone together, take my time obviously, I don't need to reseal it. If I keep it away from all dirt, debris and water naturally, I should be okay."

    So needless to say after replacing the battery and being surprised by how good the phone resealed with the cut stock adhesive I was pretty shocked. But if you want to rebind it with new adhesive I PROMOTE IT. Check amazon? I am not sure what size tape you need.

    Also! The battery date was February 8th, 2021, so that made me happier, the old one was 8-27-2018.
    I expected an old stock, not only a few months old. To me that's NEW.

    TO THE GOOGLE!
    2
    No issues during install?
    Just Installed. Dirty flash. No issues so far...
    2
    Wow...10.3.11 within weeks of 10.3.10 release...and the official OnePlus support page for the 6T is still on 10.3.9...

    Wondering what the “Fixed known issues” are to be honest... higher than normal Battery drain maybe?

    Just sharing some info on my battery situation that started 3/4 days after my update to 10.3.10... I notice thatvthe battery was draining more quickly than usual after seeing a dramatic drop in % after some goog Google News read. Web surfing, etc...nothing out of the ordinary tbh.

    I think my battery has lost its capacity to charge to a full 3700 mAh...

    OP Support is suggesting to factory reset and see if the drain is still happening on OOS 10.3.10.

    However, I did use the OnePlus Diagnostic v1.0.0.19, and the Battery Stat does say “73% Serious Loss” and AccuBattery shows 2859mAh after a full charge to 100%, which it says the Health of the battery is @ 77%.

    After reading extensively about Li-On batteries, I came across information saying that when these batteries go below 80%...it is recommended to change it, as the battery performance will start to drop more & more rapidly on the capacity to charge.

    I'm convinced the battery need changing...as Li-On batteries are based on charging cycles...and I was charging the device every single day overnight and when in the car (everyday) it was plugged in and was using Waze & spotify...

    If anyone else out there is having a higher than normal Battery Drain issue, please share here, maybe it's the OOS, or I just kept overcharging for long periods of time (maybe)...

    Tks!

    ✌️
    I got this one, changed in like 20 minutes with a hair dryer and razor blades, getting 10+ hours again with Advanced charge controller stopping charge at 75%

    1
    Yes, you have to do the Tmobile conversion with the msm tool on the 6t. It's worth it though.
    It's my wife's phone and I plan on doing it the next time I have some free time. I've been kicking myself for not realizing the phone I bought for her wasn't the global one. It's definitely a pain for stuff like this.
  • 148
    3a5uOVJ.png

    Hey everyone,

    We are starting to push the incremental rollout of OxygenOS 10.3.7 for OnePlus 6T.

    Changelog
    Code:
    [B]System:[/B]
    • Newly added "Hide silent notifications in status bar" feature to filter unimportant notifications, making the app notification management easier( Route: Settings>Apps & Notifications> Notifications> Advanced> Hide silent notifications in status bar )
    • Fixed the small probability issue that Screenshot may fail
    • Updated Android Security Patch to 2020.11
    • Improved system stability and fixed general bugs
    [B]Game Space:[/B]
    • Newly added gaming tools box for convenient switches of Fnatic mode. You can now choose three ways of notifications: text-only, heads up and block, just for your immersive gaming experience
    • Newly added quick reply feature in a small window for WhatsApp and INS (Enable it by swiping down from upper right/left corners of the screen in gaming mode)
    • Newly added mis-touch prevention feature. Enable it, swipe down from the top of the screen, click and the notification bar will pop out

    Explore what's new on Android 10 here.

    This OTA will have a staged rollout. The OTA will be received by a limited number of users today and will have a broader rollout in a few days after making sure there are no critical bugs. Using VPN to download this build might not work as the rollout Is not based on regions and is randomly pushed out to a limited number of devices.

    For those who were on previous versions for OnePlus 6 and OnePlus 6T, we appreciate your active feedback and for reaching out to us. With your help, we have been able to better optimize and improve several key areas. Thank you for your patience and as always, we look forward to getting your continued feedback via the Community app.

    If you don't have the Community app installed on your device, feel free to download it HERE. You can check here for more information on the integrated Feedback tool. Make sure to let us know how you feel about the build here in the thread too, we look forward to reading your feedback.

    Downloads



    Full Update

    Stock Boot Image
    • 10.3.7 boot.img: Unofficial Link
    • MD5 Hash: 7d5cc8000e941d7b82a252bde6a70c29

    Magisk Patched Boot Image
    • 10.3.7 boot.img: Unofficial Link
    • MD5 Hash: 6c88998aa54ffbdcf12ecc7fc63aeb1f

    Previous Updates along with boot images:

    Custom Recoveries

    Root

    Warning: Do not flash partial update OTAs (under 1 GB) on a modified/rooted device! If you want to use partial OTAs, you must first flash the full OxygenOS zip that it applies to, and then flash the partial OTA from stock recovery. Flashing partial OTAs from TWRP will either fail or soft brick your device. You can return to a usable state by flashing one of the above full zips in recovery.



    Installation Instructions

    Download the necessary files from the section above and follow the steps below:

    Note: Dirty flashing is fine if you are running an old OxygenOS version or a ROM based on OxygenOS. If you are, however, coming from a Custom ROM, you must clean flash.

    Caution: Please remove your existing screen lock/pin/pattern/password and set it to swipe before starting the update process.



    For Non-Rooted Users with a Locked Bootloader and Stock Recovery

    1. Download the full ROM zip from the downloads section above and place it in the root of your internal memory
    2. Reboot to Stock Recovery > Shutdown device > Press Volume Down + Power buttons together
    3. Select Language > Install menu > Install from internal > Select the full zip > Flash
    4. Reboot to System
    Note: First boot may take some time, so please be patient and wait for it to boot.



    [Dirty Flash] For Users with an Unlocked Bootloader and TWRP Recovery coming from Stable OxygenOS, OxygenOS Open Beta

    1. Download the full ROM zip and TWRP recovery from the downloads section above
    2. Transfer the full ROM zip and TWRP recovery to the root of your device's internal storage
    3. Reboot to TWRP recovery and take a nandroid backup of your existing ROM
    4. From the TWRP menu, Install > Select full ROM zip > Swipe to flash
    5. From the TWRP menu, Install > Select TWRP recovery zip > Swipe to flash
    6. Reboot to TWRP recovery
    7. Flash the latest stable Magisk in case you want to root
    8. Reboot to System
    Note: First boot may take some time, so please be patient and wait for it to boot.

    Warning: Dirty flashing (update) can be risky! Remember that if you face issues after dirty flashing, you will have to clean flash.



    [Clean Flash] For Users with an Unlocked Bootloader and TWRP Recovery

    1. Download the full ROM zip and TWRP recovery from the downloads section above
    2. Transfer the full ROM zip and TWRP recovery to the root of your device's internal storage
    3. Reboot to TWRP recovery and take a nandroid backup of your existing ROM
    4. From the TWRP menu, Install > Select full ROM zip > Swipe to flash
    5. From the TWRP menu, Install > Select TWRP recovery zip > Swipe to flash
    6. Reboot to TWRP recovery
    7. From the TWRP menu, Wipe > Swipe to wipe
    8. Flash the latest stable Magisk in case you want to root
    9. Reboot to System
    Note: First boot may take some time, so please be patient and wait for it to boot.

    Never Settle.

    XDA:DevDB Information
    [Discussion & Feedback] OxygenOS 10.3.7 OTA for OnePlus 6T, ROM for the OnePlus 6T

    Contributors
    Funk Wizard, Akhil701
    ROM OS Version: Android 10
    ROM Kernel: Linux 4.x

    Version Information
    Status: Stable
    Current Stable Version: 10.3.7
    Stable Release Date: 2020-11-25

    Created 2019-02-04
    Last Updated 2020-11-25
    106
    Downloads to be moved to post 1

    Thread Maintainer assigned: @Akhil701
    89
    Flashing instructions moved to OP

    Thread Maintainer assigned: @Akhil701
    70
    Hello XDA,

    I would like to thank you all for your patience and for maintaining your cool keeping the thread under control. I had to close my 5/5T update threads at the time of Pie release delays and there was lot of drama. None the less the build should pass CTS soon and should be ok to roll out thereafter.

    I had to close the official thread once and multiple clean-ups were required over the last few days. I am glad that there is no such escalation here and would like to once again appreciate the level of patience and understanding.

    Having said all this, the update should be on its way in the coming days, so all we ask for is a little more patience.

    We are Almost there ...

    Thank you for your patience and cooperation,

    Funk Wizard
    Forum Moderator
    48
    Stable 10.3.1 is up - Link

    Mirror to AFH - AFH

    md5 - 0652ca5ac8fb83e170700248502a93ad

    Stock boot image - Stock

    Magisk patched image - Patched

    Changelog
    System:
    • Fixed the issue with a black screen appearing after unlocking device using fingerprint
    • Fixed the issue with the animation logo while rebooting device
    • Fixed the issue with the device heating up while charging
    • Fixed the random disconnection issue with 5Ghz hotspot
    • Improved system stability and fixed general bugs
    • Updated Android security patch to 2019.12

    Camera :
    • Optimised the image preview time in the Pro mode
    • Fixed the camera crash issue

    Gallery :
    • Fixed the issue with video and images not displaying in Gallery