Evira Kernel Redminote 7

[LionHeart90]

In 2.8, i selected zzmoove and i added zzmod as profile buh shows custom, is it working??

I think yes bro, but i selected as always "ybatext"; why do u use zzmod profile? what is the difference?

 

[Oleggluk]

I saw new Avira 2.9 screenshots in telegrams, 300 MHz it looks beautiful, but without adjusting the voltage, it does not make sense. (Google translator)

 

[whalesplaho]

I think yes bro, but i selected as always "ybatext"; why do u use zzmod profile? what is the difference?

Its moderate dats why i choose it... I dnt know which is better tho.

 

[@PAIN$]

I think yes bro, but i selected as always "ybatext"; why do u use zzmod profile? what is the difference?

Zzmod for balance between battery and performance

 

[xcrpt]

I think maybe -OP- is need to be update? @resurrect

 

[arielsoyyo]

k_cal does not work? every time I turn off the screen, the color settings are erased.

 

[whalesplaho]

k_cal does not work? every time I turn off the screen, the color settings are erased.

Did yhu select apply on boot... It works good here

 

[airidosas252]

I saw new Avira 2.9 screenshots in telegrams, 300 MHz it looks beautiful, but without adjusting the voltage, it does not make sense. (Google translator)

Why do you think so? Less clock speed usually results in better power consumption than, let's say, 500 MHz clock speed. And since CPU is working slower (let's put it this way - for 144 Hz monitor you would need more power to drive it comfortably, whereas 60hz will put less strain on hardware, thus better power efficiency). So your argument is vastly inaccurate.
Moreover, it depends on CPU, how much voltage at the very least is required to work on specific frequencies. One could run on basically little to no voltage, where some random CPU would require more voltage at the start, but slope wouldn't be so steep, in regards of voltage vs clockspeed scenario. Hope that makes sense.

 

[whalesplaho]

2.9 seems to be draining battery... For me tho dnt know about others!

 

[@PAIN$]

Hi sir..great update for evira kernal..I installed it and noticed massive difference in battery considering that it has lowest frequency of 300mhz for me tbh this is the best kernel for battery rn ..as always thanks for continously developing evira kernel ps:i only tested the battery drain and will test bb later :good::good:

---------- Post added at 05:37 PM ---------- Previous post was at 05:34 PM ----------

2.9 seems to be draining battery... For me tho dnt know about others!

Try adjusting the governor/io settings using kernel manager..

---------- Post added at 05:42 PM ---------- Previous post was at 05:37 PM ----------

@resurrect, can i ask if its ok to have 2.4 ghz(overclock) for big cluster..? Will it cause overheating or possible damage to the device or should i stick to lower frequencies?thank you

 

[whalesplaho]

Hi sir..great update for evira kernal..I installed it and noticed massive difference in battery considering that it has lowest frequency of 300mhz for me tbh this is the best kernel for battery rn ..as always thanks for continously developing evira kernel ps:i only tested the battery drain and will test bb later :good::good:

---------- Post added at 05:37 PM ---------- Previous post was at 05:34 PM ----------


Try adjusting the governor/io settings using kernel manager..

---------- Post added at 05:42 PM ---------- Previous post was at 05:37 PM ----------

@resurrect, can i ask if its ok to have 2.4 ghz(overclock) for big cluster..? Will it cause overheating or possible damage to the device or should i stick to lower frequencies?thank you

I did.... Used zzmoove and alucardsched plus zen and anxiety... Back to 2.8 and battery drain normal. Dnt know why. Using PE by nickinfinity.

 

[Eddywarez]

In MIUI 10.3.5 Global it is performing good, didn't see battery drain 'till now, everything works like a charm. Thanks for the great work.

:good:

Screenshot:

 

[Gueztar]

In MIUI 10.3.5 Global it is performing good, didn't see battery drain 'till now, everything works like a charm. Thanks for the great work.

:good:

So, i just bought lavender. Does instal custom recovery & evira custom kernel on MIUI global stable make safetynet fail? No need to disable verity (vbmeta) thingy right?

 

[Eddywarez]

So, i just bought lanvender. Does instal custom recovery & evira custom kernel on MIUI global stable make safetynet fail? No need to disable verity (vbmeta) thingy right?

There is no need.

:good:

 

[biomax88]

2.9 big claster very big Mhz all time, change profile not get result, big claster is crazy) back 2.8 all normal

Found a pest, it was a magic module thermo config, now 2.9 work nice

 

[M7mD.Sa3eD]

Evira Kernel break PROXIMITY SENSOR

REBO...... DON'T SAY IT, DON"T ****IN SAY IT, I rebooted like 3000 times, only the one after flashin the kernel no more

Tested on Havoc (19 June 2019) build
Tested also with Genom, everything is good

 

[Nighttor]

Evira Kernel break PROXIMITY SENSOR

REBO...... DON'T SAY IT, DON"T ****IN SAY IT, I rebooted like 3000 times, only the one after flashin the kernel no more

Tested on Havoc (19 June 2019) build
Tested also with Genom, everything is good

I used this app "play.google.com/store/apps/details?id=com.mobiledirection.proximitysensorreset"
follow the instructions and restart the phone. Fixed in miui.eu

 

[Eddywarez]

Evira Kernel break PROXIMITY SENSOR

REBO...... DON'T SAY IT, DON"T ****IN SAY IT, I rebooted like 3000 times, only the one after flashin the kernel no more

Tested on Havoc (19 June 2019) build
Tested also with Genom, everything is good

It happens in some custom roms, it happened to me in crDroids, but didn't in Bootleggers.

:good:

 

[aron11195]

add spectrum support pls

 

[Rahmanwasi]

Why do you think so? Less clock speed usually results in better power consumption than, let's say, 500 MHz clock speed. And since CPU is working slower (let's put it this way - for 144 Hz monitor you would need more power to drive it comfortably, whereas 60hz will put less strain on hardware, thus better power efficiency). So your argument is vastly inaccurate.
Moreover, it depends on CPU, how much voltage at the very least is required to work on specific frequencies. One could run on basically little to no voltage, where some random CPU would require more voltage at the start, but slope wouldn't be so steep, in regards of voltage vs clockspeed scenario. Hope that makes sense.

I agree with you. I have found that changing to 300mhz dropped my battery usage around 50mV. Which is to my estimation 28% less usage of battery power from before. Performance difference is negligible. As stated by dev zzmoove cluster 2 should be 1114mhz otherwise noticeable lag is felt. So I switched to others to avoid it.